World Market 585015 User manual

CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
Assembly Instructions
Kapari Chair Natural
SKU – 585015
THANK YOU FOR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
NOT FOR COMMERCIAL USE.
Page 1

Page 2
Component List
Hardware List
Tool List
LABEL PICTURE DESCRIPTION QTY
A Chair Back 1
B Seat Frame 1
1
1
1
1
1
C
D
E
F
G
Front Left Leg
Front Right Leg
Right Armrest
Cushion
Left Armrest
LABEL PICTURE DESCRIPTION QTY
H-1 Long Allen Bolt 2
H-2
(Ø5/16" x 1-3/8”)
(Ø5/16"x1-3/16”)
Medium Allen Bolt
Short Allen Bolt
2
H-3 8
LABEL PICTURE DESCRIPTION QTY
T-1 Allen Wrench 1
（Ø5/16"x 2"）

-877store or our customer service call center 1
Page 3
Assembly Preparation
Before Beginning:
Unpack all hardware bags and components to ensure you have all parts.
Read instructions, cover to cover.
Have 2 adults on hand for assembly.
Do not assemble on flooring or carpet.
Assemble on a clean non-marring surface (packing foam).
Save all packaging until finished.
In case of missing parts, please contact your nearest Cost Plus World Market
-967-5362.

Page 4
Step 2
(H-2) Medium Allen Bolt x 2
(T-1) Allen Wrench x 1
Place Seat Frame (B) down onto a padded, non-marring surface. Secure Chair Back (A) to Seat Frame (B) using
2 Medium Allen Bolts (H-2) as shown. Engage both bolts by hand, then fully tighten using Allen Wrench (T-1).
Do not overtighten allen bolts.
(H-2)
(H-2)
(H-2)
(T-1)
B
A
Assembly Steps
Step 1
Attach Left Armrest (E) to Front Left Leg (C) as shown. Secure using 2 Short Allen Bolts (H-3). Engage both bolts
by hand, then tighten using Allen Wrench (T-1). Do not overtighten allen bolts. Repeat the same procedure for
Right Armrest (F) and Right Front Leg (D).
NOTE: The angled support on both Front Legs (C/D) should face outwards once assembled, as illustrated.
H1
(T-1)
(H-3)
(H-3)
EF
C
D
(H-3)
(H-3)
(H-3) Short Allen Bolt x 4
(T-1) Allen Wrench x 1
AngleFaces
Outwards
FRONT

Page 5
Step 3
Using a second person to assist you, carefully lay the assembly from Step 2 on its right side as illustrated. Attach
Front Left Leg (C) to Seat Frame (B) using 2 Short Allen Bolts (H-3) from the inside. Engage bolts by hand then
fully tighten them using Allen Wrench (T-1). Next, attach Left Armrest (E) to Chair Back (A) using a Long Allen
Bolt (H-1). Engage the bolt by hand then fully tighten using Allen Wrench (T-1). Do not overtighten any of the
allen bolts.
(H-1)
(T-1)
A
C
E
B
(H-3)
(T-1)
(H-3)
(H-3) Short Allen Bolt x 2
(H-1) Long Allen Bolt x 1
(T-1) Allen Wrench x 1
FRONT
TOP

Page 6
Step 4
(H-1)
(H-3)
B
A
F
D
(H-3)
(T-1)
(T-1)
Using a second person to assist you, carefully rotate the assembly from Step 3 onto its left side as illustrated.
Attach Front Right Leg (D) to Seat Frame (B) using 2 Short Allen Bolts (H-3) from the inside. Engage bolts by
hand then fully tighten them using Allen Wrench (T-1). Next, attach Right Armrest (F) to Chair Back (A) using a
Long Allen Bolt (H-1). Engage the bolt by hand then fully tighten using Allen Wrench (T-1). Do not overtighten
any of the allen bolts.
(H-3) Short Allen Bolt x 2
(H-1) Long Allen Bolt x 1
(T-1) Allen Wrench x 1
TOP
FRONT

Page 7
Step 5
Step 6
Using a second person to assist you, carefully turn the chair assembly upright as shown. Insert Cushion (G) onto
Seat Frame (B) and use the cushion ties to secure the cushion to the chair.
Assembly is now complete and the chair is ready for use.
NOTE: Check that all bolts are fully tightened every 3 months to ensure stability.
G
B
WEIGHT LIMITS 275LBS

Page 8

Cushion and slip cover care:
· Remove the slip cover from the cushion insert.
· Do not wash the cushion insert.
· Machine wash in cold water with similar colors using delicate cycle only.
· Line dry or lay at.
· Warm iron if needed.
For minor spots wipe with a we cloth and mild detergent.
Slip covers can also be placed in a washing machine using cold water, mild detergent and
placed on gentle cycle. Do not use bleach. Remove the insert.
Line dry, do not place in the dryer.
We use a higher density foam to ensure the cushions do not break down in the
outdoor elements. Cushions will soften over time.
Flip the cushions to maintain the quality.
CAUTION: As with any wood, the color may fade if left in direct sunlight or
inclement weather. Minor cracking may occur with age. These are naturally
occurring features of wood and do not aect product performance.
We recommend using our Outdoor Wood Furniture Finish sold separately to help
preserve and protect the wood and nish.