World Market Jagger 626728 User manual

R
Jagger Record Cabinet 36''W
SKU 626728
PAGE 1
2023.07.27
Assembly Instructions
ALL PRODUCTS SOLD AT WORLD MARKET ARE NOT
FOR COMMERCIAL USE AND ARE INTENDED FOR
RESIDENTIAL USE ONLY
Thank you for your purchase. If you have any questions pertaining to the assembly of this
furniture piece, please contact the nearest World Market store. If you are not near a store,
please call our customer service call center toll free at 877-967-5362 for assistance.

LABEL DESCRIPTION Q.TY
PICTURE
Component List
1
Top Frame
A
Bottom Frame
Left Side Frame
Right Side Frame
1
1
B
1
C-1
C-2
D-1
D-2
Left Divider Frame 1
Right Divider Frame
Fixed Shelf
1
Mid Back Rail 1
E
F
Back Panel
Leg
G
I
1
4
FRONT
FRONT
FRONT
FRONT
FRONT
FRONT
FRONT
FRONT
TOP
TOP
TOP
TOP
TOP
TOP
TOP
TOP
TOP
TOP
FRONT
1
PAGE 2

Anti Tip-kit
Lock Washer Ø8 x Ø13 x T2 mm
Nut M8 x 13 mm
14
Cam lock Ø15 mm
Pan head Screw M3.5 x 25 mm
Cam Screw
Connecting Screw M7 x 50 mm
LABEL DESCRIPTION Q.TY
PICTURE
Hardware List
H-1
Flat Washer Ø8 x Ø16 x T2 mm
Triangle
LABEL DESCRIPTION QTY
1
T-2
Phillips Screwdriver
(Not Included)
PICTURE
Allen Key
4 x 110 x 30 mm
Tool List
1
T-3
1
T-1
Wrench 13 mm
T-4
H-2
H-3
H-4
H-5
H-6
H-7
H-8
H-9
Wood Screw M4 x 35 mm
14
8
4
8
8
8
2
1
1
PAGE 3

Assembly Preparation
Before Beginning:
Read the assembly instructions, cover-to-cover. Save any Care and Maintenance instructions pages for
after the assembly has been completed.
In case of missing parts, please contact your nearest World Market store or call our customer service call
center at call 1-877-967-5362.
Assemble on a clean non-marring surface (such as the product's packing foam).
Unpack all hardware bags and components to ensure you have all parts. Take note of bolt hardware
size differences and components that may have directional labels (Example: TOP or FRONT).
It is always recommended to have 2 adults on hand for assembly.
Do not assemble on hard, abrasive flooring or carpeted surfaces that can damage or get caught in the
components during assembly.
Do not discard any packaging until the product has been fully assembled.
WARNING: Small parts are a choking hazard. Adult supervision is required before, during, and after
assembly.
PAGE 4

Step 1
(T-4) Phillips Screwdriver
(H-2) Cam Screw x 14
Assembly Steps
Step 1.1: Place Top Frame (A) upside down onto a padded, non-marring surface. Install Cam Screws (H-2) into the
pre-drilled holes on Top Frame (A) as shown. Fully tighten using a Phillips screwdriver (T-4, not included) per
illustration above.
Step 1.2: Place Left Side Frame (C-1) and Right Side Frame (C-2) upside down onto a padded, non-marring
surface. Install Cam Screws (H-2) into the pre-drilled holes on Left/ Right Side Frame (C-1/ C-2) as shown. Fully
tighten using a Phillips screwdriver (T-4, not included) per illustration above.
Step 1.3: Place Fixed Shelf (F) upside down onto a padded, non-marring surface. Install Cam Screws (H-2) into the
pre-drilled holes on Fixed Shelf (F) as shown. Fully tighten using a Phillips screwdriver (T-4, not included) per
illustration above.
Step 1.1:
x14
IMPORTANT:
Please make note of the different
hardware sizes and ensure you are
using the correct size hardware (bolts,
screws, and washers) for each step.
T-4
H-2
FRONT OF
PANELS
FRONT
Step 1.2:
Step 1.3:
A
F
C-1
C-2
TOP
Make sure Cam Screws are
tightened fully as shown
PAGE 5

Step 3
Step 2
F
E
H-8
(T-4) Phillips Screwdriver T-4
x2
TOP
FRONT
(H-8) Wood Screw x 2
Position Mid Back Rail (E) with Fixed Shelf (F) by inserting pre-installed dowels into the corresponding holes.
Secure Mid Back Rail (E) to Fixed Shelf (F) with Wood Screws (H-8) using Phillips Screwdriver (T-4; not
included). DO NOT OVER TIGHTEN.
Carefully position Left and Right Divider Frames (D-1 and D-2) with assembly from previous step as shown above.
Ensure the Divider Frames are oriented correctly with the front edge facing the same direction as the front edge of
the Fixed Shelf (F). Insert the Cam Screws (H-2) and dowels installed in the Fixed Shelf (F) into the corresponding
holes in the Left and Right Divider Frames (D-1 and D-2). Insert Cam Locks (H-1) into Divider Frames as
illustrated above. Ensure that the arrows of the Cam Locks (H-1) are pointing toward their corresponding Cam
Screws (H-2) upon insertion. Once placed, fully tighten Cam Locks (H-1) by turning clockwise using the provided
Allen Key (T-1) until snug. DO NOT over tighten.
D-2
D-1
F
x4
Follow arrow
direction
H-1
(H-1) Cam Lock x 4
(T-1) Allen key
FRONT
H-2
T-1
TOP
PAGE 6

Step 4
Step 5
(H-1) Cam Lock x 4
(T-1) Allen key
Follow Arrow
direction
x4
H-1
T-1
G
D-1
D-2
F
C-2
C-1
H-2
GC-2
Position Left and Right Side Frames (C-1 and C-2) to assembly by inserting pre-installed Cam Screws (H-2) and
dowels into corresponding holes. Once positioned, insert Cam Locks (H-1) into holes in Fixed Shelf (F), ensuring
that the arrows of the Cam Locks (H-1) are pointing toward their corresponding Cam Screws (H-2) upon insertion.
Once placed, fully tighten Cam Locks (H-1) by turning clockwise using the provided Allen Key (T-1) until snug.
DO NOT over tighten.
NOTE: Ensure the Back Panel (G) is resting in the grooves of the Left and Right Side Frames (C-1 and C-2).
Using a second person to assist you, carefully turn assembly as shown above. Install Back Panel (G) into the inner
groove of the Fixed Shelf (F) and make sure Back Panel (G) is oriented correctly.
F
G
E
D-1
D-2
E
G
F
TOP
FRONT
FRONT
TOP
PAGE 7

Step 7
Step 6
Follow arrow
direction
x4
(H-1) Cam Lock x 4 (T-1) Allen key
A
B
(T-3) Triangle
H-1
T-1
Triangle
90°
C-2
C-1
D-2
D-1
(T-1) Allen key
(H-3) Connecting Screw x 8
T-1
x8
H-3
C-2
C-1
D-2
D-1
B
B
G
T-3
Carefully position Bottom Frame (B) with assembly, making sure it is oriented correctly. Secure Bottom Frame (B)
to assembly by first engaging all Connecting Screws (H-3) then fully tightening each one using provided Allen Key
(T-1). DO NOT OVER TIGHTEN.
NOTE: Ensure the Back Panel (G) is resting in the groove of the Bottom Frame (B).
F
Carefully position the Top Frame (A) with assembly, making sure it is oriented correctly. Align all previously
installed Cam Screws (H-2) and dowels with their corresponding holes in the Left and Right Side Frames (C-1 and
C-2). Once positioned, insert Cam Locks (H-1) into holes in both side frames, ensuring that the arrows of the Cam
Locks (H-1) are pointing toward their corresponding Cam Screws (H-2) upon insertion. Once placed, fully tighten
Cam Locks (H-1) by turning clockwise using the provided Allen Key (T-1) until snug. DO NOT over tighten.
NOTE: Check that the cabinet is square (90°) using the provided Triangle (T-3). If gaps are observed between either
side of the triangle and the assembly when placed in a corner, adjust the cabinet until no gaps are observed.
H-2
FRONT
TOP
FRONT
TOP
PAGE 8

(T-2) Wrench
Step 8
Step 9
(H-1) Cam Lock x 2
(H-4) Pan Head Screw x 4
(T-1) Allen key (T-4) Phillips Screwdriver
T-1
x2 H-1
Follow arrow
direction
C-2 B
G
x4 H-4
T-4
Step 8.1:
Step 8.2:
Using a second person to assist you, carefully turn the assembly upside down onto a padded, non-marring surface.
Install and secure Legs (I) to Bottom Frame (B) with Flat Washers (H-5), Lock Washers (H-6) and Nuts (H-7)
using provided Wrench (T-2), stacking the hardware in the order as shown. Engage all Nuts (H-7) first, then fully
tighten. DO NOT over tighten.
(H-5) Flat Washer x 8
(H-6) Lock Washer x 8
(H-7) Nut x 8 H-5
H-6H-7
T-2
TOP G
I
I
C-1
FRONT
Step 8.1: Using a second person to assist you, carefully position assembly with the back facing up. Insert Cam
Locks (H-1) into holes in Mid Back Rail (E), ensuring that the arrows of the Cam Locks (H-1) are pointing toward
their corresponding Cam Screws (H-2) upon insertion. Once placed, fully tighten Cam Locks (H-1) by turning
clockwise using the provided Allen Key (T-1) until snug. DO NOT over tighten.
Step 8.2: Secure Back Panel (G) to assembly with Pan head Screws (H-4) using a Phillips Screwdriver (T-4; not
included). DO NOT OVER TIGHTEN.
E
TOP
FRONT
PAGE 9

Step 10
ADJUSTABLE LEVELER
Levelers are located on the bottom of
each Leg and may be used for
additional adjustment if needed for
uneven surfaces.
Using a second person to assist you, carefully turn The Assembled Unit upright.
Assembly is now complete and the product is ready for use. Adjustable levelers are located on the bottom of each
leg and may be adjusted by turning outwards, counter-clockwise to help account for uneven surfaces.
NOTE: Hardware may loosen over time. Periodically check that all connections remain tight and adjust as needed.
PAGE 10