World Market Brinley Fixed Table User manual

Brinley Fixed Table
SKU - 534979
Assembly Instructions
THANK YOU FOR YOUR PURCHASE. IF YOU HAVE ANY QUESTIONS
PERTAINING TO THE ASSEMBLY OF THIS FURNITURE PIECE, PLEASE CONTACT
THE NEAREST COST PLUS WORLD MARKET STORE.
IF YOU ARE NOT NEAR A STORE, PLEASE CALL OUR CUSTOMER SERVICE CALL
CENTER TOLL FREE AT 877-967-5362 FOR ASSISTANCE.
Page 1

Page 2
Component
LABEL
A
B
Table Top 1
H-1 Dowel (Ø10x30mm) 8
Leg 2
DESCRIPTION QTY
List
Hardware List
Tool List
CSupport 2
DStretcher 1
EWedge 2
LABEL DESCRIPTION
H-2 Hanger Bolt (Ø8x80mm) 4
H-3 Nut (M8x7mm) 4
H-4 D Washer (29x15x8mm) 4
H-5 Long Bolt (M8x70mm) 6
QTY
T-1 Spanner (M13mm) 1
T-2 Ball Allen Key (M4x30x110mm) 1
LABEL DESCRIPTION QTY
H-7 Spring Washer (Ø8xØ14x2mm) 22
H-6 Short Bolt (M8x35mm) 12
H-8 Flat Washer (Ø8xØ20x2mm) 18

Page 3
Assembly Preparation
Read instructions, cover to cover.
Have 2 adults on hand for assembly.
Save all packaging until
Assemble on a clean non-marring surface (packing foam).
Do not assemble on ooring or carpet.
In case of missing parts contact your nearest Cost Plus World Market store or our
customer service call center 877-967-5362.
Unpack all hardware bags and components to ensure you have all parts.
Before Beginning:
C
D
E

Page 4
Assembly Steps
Step 1
Connect Hanger Bolt (H-2) with the Leg (B) as shown in the picture below.
Step 2
1. Insert 2 Dowels (H-1) into each end of Support (C) as shown.
2. Attached Supports (C) and Stretcher (D) to the Legs ((B). Secure Nut (H-3),
D Washer (H-4), Spring Washer (H-7) with the Spanner (T-1) as shown in the picture below.
Do NOT tighten any hardware yet.
B
C
B
H-2
H-1
H-1
C
B
H-2
H-4H-7H-3
T-1
B
C
D
4x
4x
4x
-

Page 5
Assembly Steps
Step 3
Step 4
Secure and Level Table
Gently tap the
wedge down into the slot
as necessary
to secure table stretcher.
Adjust levelers if
needed for stability.
A
E
B
H-5
H-7
H-8
T-2
1. Assemble Supports with Table Top. Position Table Top (A) up side down on non
marring padded surface. Secure the Supports (C) using Long Bolt (H-5),
Spring Washer (H-7) and Flat Washer (-8) onto the underside of Table Top (A).
2. Assemble Legs to Table Top. Secure Legs (B) to Table Top (A) as shown with
Short Bolt (H-6), Spring Washer (H-7) and Flat Washer (H-8).
Tighten all bolts with Ball Allen Key (T-2) once ALL hardware are engaged.
H-8
H-6
H-7
T-2
C
12x 6x

Care & Maintenance
• Do not put hot items direct ly on furniture surface.
• Do not clean furniture with harsh cleansers or polish.
• Do not place furniture in direct sunlight.
• Do not place furniture near
• Do not write on furniture without a padded barrier to protect the surface.
• Do not place furniture out side. For indoor use only.
• Dust and pick-up spills using a clean, non-colored, lint-free cloth.
• Stains may be removed with mild soap solution and damp cloth.
• Not for commercial use. For residential use only.
Page 6
heating or cooling vents.