1: Parental Guidance is suggested for children operating Helicopter.
2: Multiple Helicopters operating simultaneously must be on different Frequency Bands.
• Be sure that Helicopter Battery is fully charged and Remote Control Batteries are fresh.
• Helicopter will fly best in low wind conditions.
• Fly Helicopter in a wide open area with no people, pets, and other objects in the way.
• Do not fly in strong winds. This will make operation difficult and crash the Helicopter.
UP DOWN
FORWARD BACKWARD
ROTATE LEFT
If the Helicopter is rotating
on its own, slowly adjust
the Trim Control Knob
Switch between
High Speed & Low Speed
Modes
Switch LED
Light Modes
ROTATE RIGHT
HERCULES
NANO
3.5 Channel IR Helicopter
ITEM NO. 35939
• Unscrew cover and install 6x AA Batteries as shown.
• Please note polarity and orientation of batteries.
REMOTE CONTROL TRANSMITTER HELICOPTER TAKEOFF ADJUSTMENTS
FLIGHT CONTROLS
CHARGING
TROUBLESHOOTING
PREFLIGHT CONDITIONS
BATTERY INSTALLATION
1: Place Helicopter on a flat surface. Turn on the Transmitter and the Helicopter
2: Check surroundings to be sure that it is clear of people, animals, and obstructions.
3: Slowly push the Throttle Stick up to increase blade speed for lift.
4: Adjust throttle input to maintain a steady hover.
The Left and Right Sticks will move the helicopter as follows:
1: Helicopter can be charged from: USB, Controller,
or AC Charger
2: Move the Helicopter Power Switch to the OFF position
3: Connect Charging Adapter to Helicopter Charge Port.
4: Once charging is complete, disconnect Charging Plug
from Helicopter.
5: Helicopter is ready for flight.
USB CONTROLLER AC CHARGER
The Transmitter
indicator LED
does not work
No control
of the helicopter
Helicopter is
not flying high
enough
Batteries installed with the wrong polarity.
Point Transmitter at Helicopter or operate in conditions
with less sunlight.
Helicopter is not IR receiving signal from
transmitter.
Test the control functions of the helicopter in a
hover by applying light throttle and testing left and
right controls.
Helicopter is not receiving signal from
transmitter correctly.
Push Left Control Stick up for more rotor speed.Rotor speed is too slow.
Fully charge helicopter before use.Batteries are drained.
Fly helicopter in calm conditions.Windy Conditions.
Check the polarity of the batteries and install them
Correctly.
Batteries are drained. Install new batteries.
AGES 8+
1. Power Indicator LED
2. Power Switch
3. Throttle Control Stick
4. Channel Selector
5. Rudder Control Stick
6. Trim Adjustment Knob
7. Infrared Emitter
8. Throttle Speed Regulator
9. LED Light Control
Website: www.worldtechtoys.com
Phone: (877) 498-8697
Monday - Friday / 9:00AM - 5:00PM / Pacific Time
WWW.WORLDTECHTOYS.COM
MADE IN CHINA
SPECIFICATIONS, COLORS AND CONTENT MAY VARYFROM ILLUSTRATIONS
ATTENTION
READ THESE INSTRUCTIONS BEFORE OPERATING THE HELICOPTER
- Install only new batteries of the same type in
your product.
- Failure to insert batteries in the correct polarity,
as indicated in the battery compartment, may
shorten the life of the batteries or cause
batteries to leak.
- Do not mix old and new batteries.
- Do not mix Alkaline, Standard (Carbon-Zinc) or
Rechargeable (Nickel Cadmium) or (Nickel Metal
Hydride) batteries.
- Do not dispose of batteries in fire.
- Batteries should be recycled or disposed of as
per state and local guidelines.
BATTERY CHARGING INDICATORS:
RED light on USB charger will turn on when
plugged in and is not charging the helicopter.
Red light will turn off when the helicopter
battery is charging.
When charging from the remote, the
power/charge indicator LED light will turn yellow
when charging. The light will turn RED when
the helicopter is fully charged.
USB CHARGER
POWER SWITCH
CHARGING PORT
