World Tech Toys Nano Titan 34921 User manual

TITAN
NANO
3.5 CHANNEL IR HELICOPTER
AGES 14+
INSTRUCTION MANUAL
ITEM NO. 34921

• Be sure that Helicopter Battery is fully charged and Remote Control Batteries are fresh.
• Helicopter will fly best in low wind conditions.
• Fly Helicopter in a wide open area with no people, pets, and other objects in the way.
•
Do not fly in strong winds. This will make operation difficult and crash the Helicopter.
1: Parental Guidance is suggested for children operating Helicopter.
2: Multiple Helicopters operating simultaneously must be on different Frequency Bands.
• Unscrew cover and install 6x AA Batteries as shown.
• Please note polarity and orientation of batteries.
REMOTE CONTROL TRANSMITTER
PREFLIGHT CONDITIONS
BATTERY INSTALLATION
THROTTLE
CHANNEL SELECTOR
LIGHT BUTTON INFRARED EMITTER TURBO BUTTON
FORWARD/BACKWARD/
LEFT TURN/RIGHT TURN
POWER SWITCH
TRIM KNOB

UP DOWN
FORWARD BACKWARD
TURN LEFT TURN RIGHT
HELICOPTER TAKEOFF
FLIGHT CONTROLS
1: Place Helicopter on a flat surface. Turn on the Transmitter and the Helicopter
2: Check surroundings to be sure that it is clear of people, animals, and obstructions.
3: Slowly push the Throttle Stick up to increase blade speed for lift.
4: Adjust throttle input to maintain a steady hover.
The Left and Right Sticks will move the helicopter as follows:

If the Helicopter spins to the left or right
in flight without your input, you will
need to adjust the trim.
Switch between
High & Low Speed
Modes
LIGHT
BUTTON
Helicopter spins to the left.
Slowly twist the trim knob to
the right until the helicopter
stops spinning.
Helicopter spins to the right.
Slowly twist the trim knob to
the left until the helicopter
stops spinning.
ADJUSTMENTS
CHARGING
TROUBLESHOOTING
Helicopter can be charged from the USB Charger or Remote Controller
Charge Time is approximately 30 Minutes. Flight time is 5-7 minutes.
USB CONTROLLER
The Transmitter
indicator LED
does not work
No control
of the helicopter
Helicopter is
not flying high
enough
Batteries installed with the wrong polarity.
Point Transmitter at Helicopter or operate in conditions
with less sunlight.
Helicopter is not IR receiving signal from
transmitter.
Test the control functions of the helicopter in a
hover by applying light throttle and testing left and
right controls.
Helicopter is not receiving signal from
transmitter correctly.
Push Left Control Stick up for more rotor speed.Rotor speed is too slow.
Fully charge helicopter before use.Batteries are drained.
Fly helicopter in calm conditions.Windy Conditions.
Check the polarity of the batteries and install them
Correctly.
Batteries are drained. Install new batteries.
USB CHARGER:
1.) Make sure the helicopter switch is the in the off position.
2.) Plug the USB Charger to a USB port and connect the other
end to the bottom of the helicopter.
3.) The RED light on the USB Charger will turn on when the
helicopter is fully charged.
Transmitter Charger:
1.) Make sure the helicopter switch is the in the off position.
2.) Connect the Transmitter Charging Cord, located on the back of
the Transmitter, to the bottom of the helicopter.
3.) Turn on the Transmitter. The light on the Transmitter will be RED
when charging.
4.) The light on the Transmitter will turn GREEN when the helicopter
is fully charged.

Website: www.worldtechtoys.com
Email: [email protected]
Phone: [phone]
Monday - Friday / 9:00AM - 5:00PM / Pacific Time
WWW.WORLDTECHTOYS.COM
MADE IN CHINA
SPECIFICATIONS, COLORS AND CONTENT
MAY VARY FROM ILLUSTRATIONS
ATTENTION
READ THESE INSTRUCTIONS BEFORE OPERATING THE HELICOPTER
- Install only new batteries of the same
type in your product.
- Failure to insert batteries in the
correct polarity, as indicated in the
battery compartment, may shorten the
life of the batteries or cause batteries
to leak.
- Do not mix old and new batteries.
- Do not mix Alkaline, Standard
(Carbon-Zinc) or Rechargeable (Nickel
Cadmium) or (Nickel Metal Hydride)
batteries.
- Do not dispose of batteries in fire.
- Batteries should be recycled or
disposed of as per state and local
guidelines.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions.
1) This device may not cause harmful interference.
2) This device must accept any interference
received, including interference that may cause
undesired operation.