Worx WX858.9 User manual

WX858.9
20V Cordless random orbital waxer/polisher
20V בכרל תשטלמ


7 6
3
4
5
21

2
1
ONOFF
D1
B
C
E1D2
A2A1
A3
E2 E3
F G

2
1
ONOFF
D1
B
C
E1D2
A2A1
A3
E2 E3
F G

6
20V Cordless random orbital waxer/polisher EN
PRODUCT SAFETY
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat,
oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger on
the switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair and clothing
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become
complacent and ignore tool safety
principles. A careless action can cause severe
injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or remove the battery pack,
if detachable, from the power tool before
making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.

7
20V Cordless random orbital waxer/polisher EN
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools and accessories.
Check for misalignment or binding of
moving parts, breakage of parts and any
other condition that may affect the power
tool’s operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may create
a risk of fire when used with another battery
pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to
fire or excessive temperature. Exposure
to fire or temperature above 130 °C may cause
explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside
the temperature range specified in the
instructions. Charging improperly or at
temperatures outside the specified range may
damage the battery and increase the risk of fire.
6) Service
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts.This will ensure that the
safety of the power tool is maintained.
b) Never service damaged battery packs.
Service of battery packs should only be
performed by the manufacturer or authorized
service providers.
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open or shred cells or
battery pack.
b) Do not short-circuit a battery pack. Do
not store battery packs haphazardly in
a box or drawer where they may short-
circuit each other or be short-circuited
by conductive materials. When battery
pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that
can make a connection from one terminal to
another. Shorting the battery terminals together
may cause burns or a fire.
c) Do not expose battery pack to heat or fire.
Avoid storage in direct sunlight.
d) Do not subject battery pack to mechanical
shock.
e) In the event of battery leaking, do not
allow the liquid to come into contact
with the skin or eyes. If contact has been
made, wash the affected area with copious
amounts of water and seek medical
advice.
f) Seek medical advice immediately if a cell
or battery pack has been swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a
clean dry cloth if they become dirty.
i) Battery pack needs to be charged before
use. Always refer to this instruction and
use the correct charging procedure.
j) Do not maintain battery pack on charge
when not in use.
k) After extended periods of storage, it may
be necessary to charge and discharge
the battery pack several times to obtain
maximum performance.
l) Battery pack gives its best performance
when it is operated at normal room
temperature (20 °C ± 5 °C).
m) When disposing of battery packs, keep
battery packs of different electrochemical
systems separate from each other.
n) Recharge only with the charger specified
by Worx. Do not use any charger other
than that specifically provided for use

8
20V Cordless random orbital waxer/polisher EN
with the equipment. A charger that is suitable
for one type of battery pack may create a risk of
fire when used with another battery pack.
o) Do not use any battery pack which is not
designed for use with the equipment.
p) Keep battery pack out of the reach of
children.
q) Retain the original product literature for
future reference.
r) Remove the battery from the equipment
when not in use.
s) Dispose of properly.
t) Do not mix cells of different manufacture,
capacity, size or type within a device.
u) Do not remove battery pack from its
original packaging until required for use.
v) Observe the plus (+) and minus (–) marks
on the battery and ensure correct use.
SYMBOLS
To reduce the risk of injury, user
must read instruction manual
Wear ear protection
Wear eye protection
Wear dust mask
Batteries may enter water cycle
if disposed improperly, which
can be hazardous for ecosystem.
Do not dispose of waste
batteries as unsorted municipal
waste.
Do not burn
Li-Ion
Li-Ion
Li-Ion batteryThis product has
been marked with a symbol
relating to ‘separate collection’
for all battery packs and battery
pack. It will then be recycled or
dismantled in order to reduce
the impact on the environment.
Battery packs can be hazardous
for the environment and for
human health since they contain
hazardous substances.
COMPONENT LIST
1. ON/OFF SWITCH
2. BATTERY PACK RELEASE BUTTON *
3. BATTERY PACK *
4. HANDLE
5. FOAM PAD
6. ELASTIC APPLICATOR BONNET
(TERRY CLOTH BONNET)
7. ELASTIC BUFFING BONNET (WOOL
BONNET)
* Not all the accessories illustrated or
described are included in standard delivery.
TECHNICAL DATA
WX858.9
Voltage 20VMax.**
No load speed 3800 /min
Run time 40 mins
Base plate size 178 mm
Machine weight
(bare tool) 1.5 kg
** Voltage measured without workload. Initial
battery voltage reaches maximum of 20 volts.
Nominal voltage is 18 volts.

9
20V Cordless random orbital waxer/polisher EN
ACCESSORIES
WX858.9
Wool bonnet 1
Terry cloth bonnet 1
We recommend that you purchase your accessories
from the same store that sold you the tool. Refer to
the accessory packaging for further details. Store
personnel can assist you and offer advice.
OPERATING
INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
Intended Use
The machine is intended for polishing floor, car and
other coated surfaces.
1. INSTALL/REMOVE THE BATTERY PACK
To install: Place the switch in the OFF (O) position.
Then, slide the battery pack into the polisher. (See
Fig.A1)
To remove: Place the switch in the OFF (O) position.
Then, press the button to remove the battery pack
from the polisher. (See Fig.A2)
2. ON/OFF SWITCH (SEE FIG.B)
Always start and stop the polisher against the car
surface. Slide switch to the ON (I) position to start
the polisher, pull backward to OFF (O) position to
stop it.
3. Polishing
3.1 Place the polishing bonnet (wool bonnet)
over the sponge pad (see Fig. C) (If no
polishing is needed, proceed with waxing
directly (4). Ensure the car is washed clean
before polishing or waxing
Set the switch to OFF (O) position and remove the
battery pack. Place the polishing bonnet (wool
bonnet) over the sponge pad and always make
sure that its elastic strip is securely adhered to the
sponge pad.
3.2 Spread the polish (car wax)
Spread about a teaspoonful of polish (car wax)
evenly over the surface of the pad cover. Do not
apply polish (car wax) directly to the car.
Most polish (car wax) is either a paste or liquid
form. Read all instructions for proper application
and use before operation
Spread polish paste (see Fig. D1)
Spread about a teaspoonful of polish evenly over
the waxing bonnet using a putty knife or other tool
with a broad flat blade. Do not apply it directly to
the surface to be polished.
Apply liquid polish (see Fig. D2)
Spread a small amount of polish in the size of about
half a coin around the center of the waxing bonnet
and then apply it in a circle, with each circle slightly
larger than the previous one.
Note: Do not apply too much polish at once.
Having it fully soaked will affect the duration and
effectiveness of the polish.
3.3 Polish with the car polisher
Hold the polisher against the surface and slide the
ON/OFF switch to the ON (I) position. First, use wide
sweeping strokes to polish larger surfaces such as
the front hood, trunk and roof. Do not apply excess
pressure on the polisher. After covering the plane
surfaces, polish the curved surfaces such as car
doors in cycles. When done with the entire surface,
turn off the polisher. Lift the polisher off from the
surface only after the sponge pad stops rotating.
(See Fig. E1)
Note: It is also convenient to polish the car roof
and side panels by one hand. (See Fig. E2)
Polishing a smaller surface area (see Fig. E3)
For hard-to-reach areas such as bottom of the
bumpers or the side mirrors, polish them by hand.
Wipe off the residual powder with clean towel after
finishing polishing.
4. Waxing
4.1 Place the waxing bonnet (terry-cloth bonnet)
over the sponge pad (see Fig. F)
Place the waxing bonnet (terry-cloth bonnet) over
the sponge pad and always make sure that its
elastic strip is securely adhered to the sponge pad.
4.2 Repeat steps 3.2 to 3.3 to finish waxing evenly.
5. BUFFING AND POLISHING - REMOVING
THE WAX FROM THE SURFACE (SEE FIG. G)
NOTE: Wait until wax has dried to an even haze on
vehicle. Remove wax in the same order in which it
was applied.
Turn the polisher to the ON position. Polish and buff
the entire surface until all dried wax is removed.
Remove the bonnet from time to time and shake
out the residue.The bonnet with excess residue
will cause streaking.You may need to replace the
bonnet if you can't get it clean enough to avoid
streaking. Final buffing and polishing use a clean
bonnet.
NOTE: For best results, use long, sweeping strokes
in a criss-cross pattern when removing wax.
WORKING TIPS FOR YOUR
POLISHER
1. For best results, the surface should be clean and
dry. Most high-gloss surfaces can be cleaned
with mild soap and water solution.To remove

10
20V Cordless random orbital waxer/polisher EN
stubborn dirt, such as road tar, grease, and bug
stains, use a mild ammonia solution, such as
one used in glass cleaners. Before using any
cleaning product, follow the instructions for
use.
2. Always let the polisher work and do not force
it or apply excessive pressure on the polisher.
Preferably, use a light circular motion. Random
orbital motion on this tool is better when less
pressure is applied. Pressing too hard will slow
down the machine's movement and affect the
quality of work.
3. However, the most common mistake is to use
too much wax. If pad absorbs too much wax, it
will not last long, and polishing is more difficult
and takes longer.
4. If bonnet continually comes off pad, please try
with a new bonnet.
5. If the wax seems difficult to polish, you may
have used too much wax. Apply wax in a
thin, even coat.Too much wax does not add
any more protection and only makes the wax
removal more difficult
TROUBLESHOOTING
1. If the polisher does not abrade surface, checking
the bonnet. If the bonnet has been worn, replace
the new bonnet and try again.
2. If a fault can not be rectified, return the tool to an
authorized dealer for repair.
MAINTENANCE
Remove the battery pack from the machine
before carrying out any adjustment, servicing
or maintenance.
Your power tool requires no additional lubrication
or maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to
clean your power tool. Wipe clean with a dry cloth.
Always store your power tool in a dry place. Keep
the motor ventilation slots clean. Keep all working
controls free of dust. Occasionally you may see
sparks through the ventilation slots.This is normal
and will not damage your power tool.
FOR BATTERY TOOLS
The ambient temperature range for the use and
storage of tool and battery is 0℃-45℃.
The recommended ambient temperature range for
the charging system during charging is 0℃-40℃.
ENVIRONMENTAL
PROTECTION
DISPOSAL
The machine, its accessories and
packaging materials should be sorted for
environmentally friendly recycling.
The plastic components are labeled for categorized
recycling.

רוציי תנש
Check code (2 digits)
Serial No. (8 digits)
Month (2 digits)
Space (1 digit)
Year (4 digits)

4
20 בכרל תשטלמ HEV
תשטלמה רובע הדובעל םיפיט
ךלש
1
2
3
4
5
תויעב ןורתפ
1
2
הקוזחת
וא תורש תולועפ ,םינוויכ עוציב ינפל עקשהמ עקתה תא וקתנ
.הקוזחת
הללוס ילכ רובע
.45℃0℃
.40℃0℃
הביבסה לע הנגה
ןשי רישכמ קוליס
מ”עב סיסקל םוקימס :הרבחה םש
הדוהי ןבא 9090 .ד.ת המידק יברעמ ת”א :תבותכ
09-7611222 :ןופלט
www.semicom.co.il

20 בכרל תשטלמ HE
3
V
גופס תירכ .5
)ירט דב תפנצמ( תיטסלא רוטקילפא תפנצמ .6
)רמצ תפנצמ( תיטסלא גניפאב תפנצמ .7
חולשמב םילולכ םיראותמ וא םירייוצמה םירזיבאה לכ אל *
.ליגר
םיינכט םינותנ
WX858.9
** 20V
3800
40
178
1.5
(
20
.V 18V
רזיבא
WX858.9
1
1
הלעפה תוארוה
ינפל תוארוהה תרבוח תא בר ןויעב וארק :הרעה
.ילכב שומישה
דעוימ שומיש
הללוס זראמ תרסה\תנקתה תוארוה .1
ON (O:הנקתה
(A1
OFF (O:הרסה
(A2
)B רויא האר(ON/OFF גתמ .2
OFF (O
שוטיל .3
גופסה תירכ לעמ )רמצ תפנצמ(3.1
תורישי גניסקווה םע ךשמה ,שוטילב ךרוצ ןיא םא( )C רויא האר(
גניסקוו וא שוטיל ינפל יקנו ףוטש בכרהש אדוו .)4
OFF (O
)בכר תוועש( שילופה תחירמ 3.2
)D1 רויא האר( שילופ תחשמ תחירמ
)D2 רויא האר( ילזונ שילופ תייצקילפא
בכרל תשטלמה תרזעב שילופ 3.3
ON (I
)E1 רויא האר(
)E2 רויא האר(
)E3 רויא האר( רתוי ןטק םינפ חטש שוטיל
גניסקוו .4
4.1
(F
3.33.24.2
)G רויא האר( חטשמהמ הוועשה תרסה - שוטילו גניפאב .5
ON
:הרעה

2
20 בכרל תשטלמ HEV
הרוטרפמטל וא שאל ילכ וא תוללוס זראמ ףושחל ןיא .ו
130°C .הגירח
זראמ תא ןועטל ןיא .הניעטה תוארוה לכ לע דיפקהל שי .ז
ןיוצמה חווטהמ תגרוחה הרוטרפמטב ילכה וא תוללוסה
.תוארוהב
תוריש6(
יאנכט י"ע ןתניהל ילמשחה הדובעה ילכל תורישה לע .א
.םיירוקמ ףוליח יקלחב שמתשמה ךמסומ
.םימוגפ תוללוס יזראמ ןקתל תוסנל ןיא .ב
הללוסל תוחיטב תוארוה
וא הללוסה יאת תא וסרגת לאו וחתפת לא ,וקרפת לא .א
.הללוסה
זגראב הזפוחב תוללוס ונסחאת לא .הללוסה תא ורצקת לא .ב
וא היינשה תא תחא רצקל תולוכי ןה םהב הריגמב וא
.םיכילומ םירמוח י"ע רצקתהל
תכתמ יצפח םע עגמב אובת אל הללוסהש ורהזיה שומישה ןמזב
וא םיגרב ,םירמסמ ,תוחתפמ ,תועבטמ ,ריינ תוכיס ןוגכ
רצק .םיעקשה ינש ןיב רוביחל םורגל םילולעה םימוד םיצפח
.תויווכל וא הפירשל םורגל לולע םיעגמב לופכ
ןוסחאמ וענמיה .שאל וא םוחל תוללוסה תא ופשחת לא .ג
.רישי שמש רואב
.תוטבחל תוללוסה תא ופשחת לא .ד
וא רועה םע עגמב אובל טילורטקלאה לזונל ורשפאת לא .ה
תויומכב עוגנה רוזאה תא ופטש .הפילד לש הרקמב םייניעה
.יאופר עויס תלבקל ונפו עגמ לש הרקמב תולודג םימ
.העילב לש הרקמב יאופר עויס תלבקל דימ ונפ .ו
הללוסה יעגמ תא ובגנ .השביו הייקנ הללוס לע ורמש .ז
.ךולכל לש הרקמב השביו הייקנ תילטמב
תוארוהב דימת ונייע .שומישה ינפל הללוסה תא ןועטל שי .ח
לא .הניעטה תוארוהל םאתהב ולעפו הלעפההו שומישה
.שומישב הניאשכ הללוסה תא ונעטת
רחאל הקירפו הניעט ירוזחמ רפסמב ךרוצ היהיו ןכתיי .ט
םיעוציב תגשהל ,שומיש אלל תוכורא ןוסחא תופוקת
.םייבטימ
הליגר רדח תרוטרפמטב יבטימ ןפואב תלעופ הללוסה .י
.)C20 ±°C5°(
וניאש ןעטמב שומיש .דבלב קפוסמה ןעטמה תועצמאב ונעט .אי
.הקילד םורגל לולע הללוסה גוסל םיאתמ
םירחא תכתמ יצפחמ שומישב הניאשכ הללוסה תא וקיחרה .בי
יצפחו םיגרב ,םירמסמ ,תוחתפמ ,תועבטמ ,ריינ יבטא ןוגכ
.הללוסה יעגמ תא רצקל םילולעה םירחא םינטק תכתמ
.הקילד וא היווכ םורגל לולע הללוסה יעגמ רוציק
;התוא םיבקנמשכ הללוסהמ ףולדל לולע טילורטקלא לזונ .גי
תולודג םימ תויומכב עוגנה רוזאה תא ופטש .עגממ וענמיה
עגמ לש הרקמב יאופר עויס תלבקל ונפו עגמ לש הרקמב
וא יוריג םורגל לולע טילורטקלאה לזונ םע עגמ .םייניעה םע
.היווכ
.הללוסה תנקתה ינפל ילכה יעגמ תאו הללוסה יעגמ תא וקנ .די
ילכ םע שומישל תודעוימ ןניאש תוללוסב ושמתשת לא .וט
.ילמשחה הדובעה
.םידלי לש םדי גשיהמ הללוסה תא וקיחרה .זט
.דיתעב ןויעל ,חוטב םוקמב תרבוחה תא ורמש .זי
.שומישב וניאשכ ילכהמ הללוסה תא וריסה .חי
ביבסל יתודידי ןפואב הללוסה תא וכילשה .טי
םינוש גוס וא לדוג ,תלוביק ,רוציי לש תוללוס בברעל ןיא .א
.ןקתהה ךותב
דע תירוקמה ותזיראהמ תוללוסה זראמ תא ריסת לא .ב
.שרדייש
ידכ הללוסה לע )-( סונימו )+( סולפ םינמיסל בל םיש .ג
.ןוכנ שומיש חיטבהל
םילמס
Li-Ion
Li-Ion
ביכר תמישר
הלעפה -יוביכ גתמ .1
* הללוסה יזראמ רורחש ןצחל .2
הללוס .3
תידי .4

20 בכרל תשטלמ HE
1
V
רצומה תוחיטב
ילכל תויללכ תוחיטב תוארוה
םיילמשח הדובע
,תוארוהה ,תוחיטבה תורהזא לכ תא אורקל שי :הרהזא
.הז הדובע ילכל םיפרוצמה םיטרפמהו םירויאה
.דיתעב ןויעל ,חוטב םוקמב תרבוחה תא ורמש
הדובעה רוזאב תוחיטב1(
.בטיה ראומו יקנ הדובע רוזא לע ורמש .א
ןוגכ ,תוציפנ תוביבסב םיילמשח הדובע ילכ וליעפת לא .ב
.קבא וא םיזג ,םיקילד םילזונ תברקב
הדובע ילכ תלעפה תעב םירחא םישנאו םידלי וקיחרה .ג
.ילמשח
תילמשח תוחיטב2(
םיעקשל םיאתהל םיילמשחה הדובעה ילכ יעקת לע .א
.םיילמשחה
הדובע ילכ רוביחל םהשלכ םיעקת ימאתמב
.םיקראומ םיילמשח
,תורוניצ ןוגכ ,םיקראומ םיחטשמ םע עגממ וענמיה .ב
.םיררקמו לושיב ירונת ,םירוטאידר
.תוחלל וא םשגל םיילמשחה הדובעה ילכ תא ופשחת לא .ג
לבכב ושמתשת לא םלועל .הניזה לבכ לע חוכ וליעפת לא .ד
תא וקיחרה .ילמשחה עקשהמ וקותינל וא ילכה תאישנל
.םיענ םיקלחמ וא םידח תווצקמ ,ןמשמ ,םוחמ לבכה
הנבמל ץוחמ שומישל םיאתמה ךיראמ לבכב ושמתשה .ה
.הנבמל ץוחמ ילמשח הדובע ילכ תלעפה תעב
ילכ תלעפהמ ענמיהל ןתינ אלשכ תחפ קספמב ושמתשה .ו
.החל הביבסב ילמשח הדובע
תישיא תוחיטב3(
תעב ןויגיהב וגהנו םישוע םתאש המל בל ומיש ,םירע ויה .א
הדובע ילכב ושמתשת לא .ילמשח הדובע ילכ תלעפה
לוהוכלא ,םירודכ תעפשה תחת וא םיפייע םתאשכ ילמשח
.תופורת וא
.ןגמ יפקשמ דימת ושבל .ישיא ןגמ דויצב ושמתשה .ב
ינפל יובכ בצמב גתמהש ואדו .היופצ יתלב הלעפה וענמ .ג
.ותאישנ וא ילכה תמרה ,הללוס וא/ו חתמ רוקמל ילכה רוביח
ילכ תלעפה ינפל םיגרב תוחתפמ וא ןונווכ תוחתפמ וריסה .ד
.ילמשחה הדובעה
דימת ורמש .םיקחורמ תומוקמל עיגהל תנמ לע וחתמתת לא .ה
.הביצי הדימע לע
.םיטישכת וא םייופר םידגב ושבלת לא .םאתהב ושבלתה .ו
םיקלח ןיבל םידגבהו רעישה ןיב קחרמ לע דיפקהל שי
.םיענ
םהש אדוול שי קבא באוש רוביחל םימאתמ םיקפוסמשכ .ז
.יוארכ םהב םישמתשמו בטיה םירבוחמ
םילכב ףוכת שומיש בקע תורכיה ובש בצממ ענמיהל שי .ח
לש תוחיטבה תונורקעמ תומלעתהלו תוננאשל ליבות
.םילכה
הקוזחתו שומיש4(
ילכב ושמתשה .ילמשחה הדובעה ילכ לע חוכ וליעפת לא .א
.המישמל םיאתמה ילמשחה הדובעה
ליעפמ וניא גתמה םא ילמשחה הדובעה ילכב ושמתשת לא .ב
.ותוא הבכמ וא
הללוסה תא ואיצוה וא/ו חתמה רוקממ עקתה תא וקתנ .ג
תפלחה ,םהשלכ םינוויכ עוציב ינפל ילמשחה הדובעה ילכמ
.ןוסחא וא םירזיבא
גשיהמ קחרה שומישב םניאש םיילמשח הדובע ילכ ונסחא .ד
םיאיקב םניאש םישנאל ורשפאת לאו םידלי לש םדי
ליעפהל הלא תוארוהב וא ילמשחה הדובעה ילכ תלעפהב
.ותוא
םיקלח רחא וקדב .םיניקת םיילמשח הדובע ילכ לע ורמש .ה
רחא יאנת לכו םירובש םיקלח ,םיפפוכמ וא םימוקע םיענ
וגאד .ילמשחה הדובעה ילכ תלועפ לע עיפשהל לולעה
.וב שומישה ינפל םוגפ ילמשח הדובע ילכ ןוקיתל
.םייקנו םידח ךותיח ילכ לע ורמש .ו
'דכו םיטיבב םירזיבאב ,ילמשחה הדובעה ילכב ושמתשה .ז
הדובעה יאנתב תובשחתה ךות ,הלא תוארוהל םאתהב
.עוציבל הדובעה תוהמבו
םייקנ ,םישבי הזיחאה יחטשמ לעו תוידיה לע רומשל שי .ח
.זירג וא ןמש אללו
ותקוזחתו הללוס לעפומ הדובע ילכב שומיש5(
.דבלב ןרציה י"ע קפוסמה ןעטמה תועצמאב ונעט .א
.דבלב ול תודעוימה תוללוס םע הדובעה ילכב ושמתשה .ב
םייתכתמ םיצפחמ ,שומישב הניאשכ ,הללוסה תא וקיחרה .ג
םיגרב ,םירמסמ ,תוחתפמ ,תועבטמ ,ריינ יבטא ןוגכ םירחא
ןיב עגמ רוציל םילולעה ,םירחא םינטק םייתכתמ םיצפח וא
.הללוסה יבטוק ינש
;הנממ ףולדל לולע הללוסה לזונ םיינוציק שומיש יאנתב .ד
.גגושב עגמ לש הרקמב םימב דימ ופטש .עגממ וענמיה
.םייניעה םע עגמ לש הרקמב יאופר עויס תלבקל ונפ ,ףסונב
רבעש וא םגפנש ילכב וא תוללוס זראמב שמתשהל ןיא .ה
.םייוניש

Copyright © 2020, Positec. All Rights Reserved.
www.worx.com
Table of contents
Languages:
Other Worx Sander manuals
Popular Sander manuals by other brands

HOLZMANN MASCHINEN
HOLZMANN MASCHINEN ZS640P user manual

DeWalt
DeWalt DW441 instruction manual

Dexter Power
Dexter Power PC280DS Legal and Safety Instructions

Drill Master
Drill Master 69487 Owner's manual & safety instructions

Black & Decker
Black & Decker RO410 instruction manual

Scheppach
Scheppach DS200 Translation of original instruction manual