Woxcon TPUH407-US User manual

TPUH407-US
4K HDBaseT 2.0 Extender
All Rights Reserved
Version: TPUH407-US_2018V1.0
User Manual

4K HDBaseT 2.0 Extender
Preface
Read this user manual carefully before using the product. Pictures shown in this
manual are for reference only. Different models and specifications are subject to real
product.
This manual is only for operation instruction, please contact the local distributor for
maintenance assistance. The functions described in this version were updated till July,
2018. In the constant effort to improve the product, we reserve the right to make
functions or parameters changes without notice or obligation. Please refer to the
dealers for the latest details.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.

4K HDBaseT 2.0 Extender
SAFETY PRECAUTIONS
To ensur e t h e b e s t performance from the pr o d u c t , p l ease read all i n s t r u c t i ons carefully
before using the device. Save this manual for further reference.
l Unpack the equipment carefully and save the original box and packing material for
possible future shipment.
l Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
l Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
l Using supplies or parts not meeting the products’ specifications may cause
damage, deterioration or malfunction.
l Refer all servicing to qualified service personnel.
l To prev e n t f i re or shock hazard, do not expose the unit to rain, moisture or install
this product near water.
l Do not put any heavy items on the extension cable in case of extrusion.
l Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
l Install the device in a place with fine ventilation to avoid damage caused by
overheat.
l Keep the module away from liquids.
l Spillage into the housing may result in fire, electrical shock, or equipment damage.
If an object or liquid falls or spills on to the housing, unplug the module immediately.
l Do not twist or pull by force ends of the optical cable. It can cause malfunction.
l Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
l Unplug the power cord when left unused for a long period of time.
l Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.

4K HDBaseT 2.0 Extender
Table of Content
1. Product Introduction ................................................................................................... 1
1.1 Features ............................................................................................................ 1
1.2 Package List ...................................................................................................... 2
2. Specification ............................................................................................................... 3
2.1 Transmitter ........................................................................................................ 3
2.2 Receiver ............................................................................................................ 4
3. Panel Description ....................................................................................................... 5
3.1 Transmitter Front Panel ..................................................................................... 5
3.2 Transmitter Rear Panel ..................................................................................... 6
3.3 Receiver Front Panel ......................................................................................... 7
3.4 Receiver Rear Panel ......................................................................................... 8
4. System Connection .................................................................................................... 9
4.1 Usage Precaution .............................................................................................. 9
4.2 System Diagram ................................................................................................ 9
5. Button Control ........................................................................................................... 10
5.1 Signal Switching .............................................................................................. 10
5.2 Display Control ................................................................................................ 10
6. RS232 Control ........................................................................................................... 11
6.1 RS232 Connection ........................................................................................... 11
6.2 RS232 Control Software .................................................................................. 14
6.3 RS232 Command ............................................................................................ 15
6.3.1 Signal Switching .................................................................................... 15
6.3.2 CEC Command ..................................................................................... 15
6.3.3 HDCP Command ................................................................................... 16
6.3.4 Button Control User-defined .................................................................. 16
6.3.5 Factory Default ...................................................................................... 17
7. Panel Drawing .......................................................................................................... 18
7.1 Transmitter ...................................................................................................... 18
7.2 Receiver .......................................................................................................... 18

4K HDBaseT 2.0 Extender
8. Troubleshooting & Maintenance ............................................................................... 19
9. Customer Service ..................................................................................................... 20

4K HDBaseT 2.0 Extender
1
1. Product Introduction
Thanks for choosing the TPUH407-US HDBaseT2.0 extender, which consists of a
wallplate transmitter and a receiver. The extender is designed to transmit HDMI (1080P,
4K@60Hz 4:2:0), RS232 and USB signal up to 328ft/100m away by using a signal
CATx cable.
The wallplate transmitter features two HDMI inputs, and one of them can be selected
as the input source by the SOURCE/AUTO button on the front panel. It also features
Type-B USB port to connect a PC or other device which needs to be controlled by the
far-end HID devices (e.g. mouse, keypad and so on), which are connected to the Type-
A USB input ports of receiver. The transmitter supports CEC: the DISPLAY ON/OFF
button on the front panel is used to control the far-end display device, and it can be
programmed by RS232 command to ensure the compatibility with various display
devices. Moreover, 24V PoC allows the transmitter can be powered from the receiver,
and the transmitter has 12V DC output for powering other device.
1.1 Features
l Supports HDMI signal up to 4K@60Hz 4:2:0.
l HDMI 1.4 standard and HDCP 2.2 compliant.
l Automatically detect active input when source is connected.
l HDBaseT technology extends HDMI, USB and RS232 signal up to 328ft/100m
over CATx cable.
l Supports bi-directional RS232 pass-through with HDBaseT connection and local
control.
l Supports CEC to turn on/off display by the DISPLAY ON/OFF button.
l Ensures display of content-protected media and interoperability with other HDCP
compliant devices.
l Supports 24V PoC wide range, the transmitter can be powered from the receiver
by the CATx cable.
l Provides 12V power supply for other device like WP series Control Panel.
l Firmware upgrade by Micro-USB port.

4K HDBaseT 2.0 Extender
2
1.2 Package List
Wallplate
transmitter
l 1x TPUH407T-US Wallplate Transmitter
l 4x Mounting Screws
l 1x 2-pin Terminal Block
l 1x 3-pin Terminal Bl o c k
Receiver
l 1x TPUH452R Receiver
l 2x Mounting Ears
l 4x Mounting Screws
l 4x Plastic Cushions
l 1x RS232 Cable (3-pin to DB9)
l 1x Power Adaptor (24V DC 1.25A)
l 1 x User Manual
Note: Please contact your distributor immediately if any damage or defect in the
components is found.

4K HDBaseT 2.0 Extender
3
2. Specification
2.1 Transmitter
Input
Input
(2) HDMI
Input Connector
(2) Type-A female HDMI
Output
Output
(1) HDBT, (1) TO PC, (1) DC OUT
Output Connector
(1) RJ45, (1) Type-B USB, (1) 2-pin terminal block
Control
Control Port
(1) FIRMWARE, (1) RS232
Control Connector
(1) Micro-USB, (1) 3-pin terminal block
General
Bandwidth
10.2Gbps
HDMI Version
1.4
HDCP Version
2.2
Video Resolution
Up to 4K×2K@60Hz 4:2:0
Transmission Mode
HDBaseT
Transmission Distance
1080P/4K@60Hz ≤ 328ft/100m
Power Supply
Powered from the receiver by CATx cable.
Operation Temperature
-10℃ ~ +55℃
Storage Temperature
-25℃ ~ +70℃
Relative Humility
10%-90%
Dimension (W*H*D)
89mm x 104.5mm x 44mm
Net Weight
250g

4K HDBaseT 2.0 Extender
4
2.2 Receiver
Input
Input
(1) HDBT, (3) USB
Input Connector
(1) RJ45, (3) Type-A USB
Output
Output
(1) HDMI
Output Connector
(1) Type-A female HDMI
Control
Control port
(1) FIRMWARE, (1) RS232
Control Connector
(1) Micro-USB, (1) 3-pin terminal block
General
Bandwidth
10.2Gbps
HDMI Version
1.4
HDCP Version
2.2
Video Resolution
Up to 4K×2K@60Hz 4:2:0
Transmission Mode
HDBaseT
Transmission Distance
1080P/4K@60Hz ≤ 328ft/100m
AC Adapter Input Power
100V~240V AC, 50/60Hz
Input Power
24V DC 1.25A
Power Consumption
23W (Max, work with the transmitter)
Operation Temperature
-10℃ ~ +55℃
Storage Temperature
-25℃ ~ +70℃
Relative Humility
10%-90%
Dimension (W*H*D)
136mm x 25.5mm x 95mm
Net Weight
365g

4K HDBaseT 2.0 Extender
5
3. Panel Description
3.1 Transmitter Front Panel
①
POWER LED: The LED illuminates red when power is applied.
②
LINK LED: The LED illuminates green when the transmitter is successfully
connected to the receiver are by a CATx cable.
③
HDCP LED:
l The LED illuminates green when the HDMI signal is transmitted with HDCP.
l The LED blinks green when the HDMI signal is transmitted without HDCP.
l The LED turns off when there is no HDMI signal input.
④
SOURCE SELECT: Press the button to select the next input source, or press and
hold it at least 3 seconds to enable auto-switching mode. For more details, please
refer to the 5.1 Signal Switching on the page 10.
⑤
DISPLAY ON/OFF: Press the button to turn on/off the display. For more details,
please refer to the 5.2 Display Control on the page 10.
⑥
TO PC: Type-B USB port to connect a PC or other device needs to be controlled.
LINK
RESET
FIRMWARE
HD MI IN 1
HD MI IN 2
TO PC
SO URC E S ELE C T
DI SPL AY ON / OFF
2
13
4
8
10
12 11
7
9
5
6

4K HDBaseT 2.0 Extender
6
⑦
HDMI IN 1 LED: The LED illuminates orange when the HDMI IN 1 port is
connected to a source device, and it will turn green once the device is selected as
input source.
⑧
HDMI IN 1: Type-A HDMI port to connect a HDMI source.
⑨
HDMI IN 2 LED: The LED illuminates orange when the HDMI IN 2 port is
connected to a source device, and it will turn green once the device is selected as
input source.
⑩
HDMI IN 2: Type-A HDMI port to connect a HDMI source.
⑪
RESET: Press the recessed button to reboot this unit.
⑫
FIRMWARE: Micro-USB port for firmware upgrade.
3.2 Transmitter Rear Panel
①
HDBT OUT (PoC IN): RJ45 HDBaseT output port to connect to the HDBT IN port
of the receiver by a CATx cable. It supports 24V PoC to enable the transmitter can
1
2
3

4K HDBaseT 2.0 Extender
7
be powered from receiver.
②
DC OUT: 2-pin terminal block to connect a compatible device which needs to be
powered.
③
RS232: 3-pin terminal block to connect a control device (such as PC) to send RS232
command to control this unit, or to connect a third party device which needs to be
controlled by RS232 pass-through. For more details, please refer to the 6. RS232
Control on the page 11.
3.3 Receiver Front Panel
①
POWER LED: The LED illuminates red when power is applied.
②
ON LED: The LED blinks green when the receiver is in the working status.
③
LINK: The LED illuminates green when the receiver is successfully connected to
the transmitter are by a CATx cable.
④
HDCP LED:
l The LED illuminates green when the HDMI signal is transmitted with HDCP.
l The LED blinks green when the HDMI signal is transmitted without HDCP.
l The LED turns off when there is no HDMI signal input.
⑤
FW: Micro-USB port for firmware upgrade.
12345

4K HDBaseT 2.0 Extender
8
3.4 Receiver Rear Panel
①
HDMI OUT: Type-A HDMI port to connect a display.
②
HDBT IN: RJ45 HDBaseT input port to connect to the HDBT OUT port on the
transmitter by a CATx cable.
③
USB IN: Three type-A USB ports to connect HID devices (e.g. mouse, keypad and
so on) to control the device which is connected to the TO PC port of the
transmitter.
④
RS232: 3-pin terminal block to connect a control device (such as PC), or to
connect a third party device which needs to be controlled by RS232 pass-through.
For more details, please refer to the 6. RS232 Control on the page 11.
⑤
DC 24V: Power port to connect the 24V DC power adaptor.
12345

4K HDBaseT 2.0 Extender
9
4. System Connection
4.1 Usage Precaution
l Make sure all components and accessories included before installation.
l System should be installed in a clean environment with proper temperature and
humidity.
l All of the power switches, plugs, sockets, and power cords should be insulated and
safe.
l All devices should be connected before power on.
4.2 System Diagram
The following diagram illustrates typical input and output connection that can be utilized
with the extender:
HDMI OUT HDBT IN USB IN
Tx Rx
RS232
DC 24V
FW
ON LINK HDCP
Rx Tx
RS23 2
PoC IN
HDBT OU T
12V
DC OUT
Transmitter
Power
PoC
HDMI Cable:
USB Cable:
Power Cable:
CATx Cabl e:
RS232 Cable:
Receiver
Projector
Projector Screen
Laptop PC

4K HDBaseT 2.0 Extender
10
5. Button Control
5.1 Signal Switching
1) Press the SOURCE SELECT button to switch to next source device, and then the
corresponding input LED will turn green.
2) Press and hold the SOURCE SELECT button at least 3 seconds to enable auto-
switching mode, and it abides by the following principles:
l New input:
Once a new input signal detected, the transmitter will automatically switch to this
new signal.
l Signal removing
Once removing the current display signal, the transmitter will automatically switch to
another active HDMI input.
l Rebooting device
The transmitter can save the last configuration before losing power. If the last
switching mode is auto-switching, the transmitter will automatically enter auto-
switching mode once rebooted, then detect all inputs and memorize their
connection status for future rebooting using. If the last selected input source is still
available, the transmitter will switch to this input. Otherwise, it will switch to the first
available active input source starting at HDMI IN 1.
l Exit auto-switching mode
The input source would remain the same when press and hold the SOURCE
SELECT button again to exit the auto mode.
5.2 Display Control
1) Press the DISPLAY ON/OFF button to turn on/off the display.
2) The DISPLAY ON/OFF can be customized by sending RS232 commands for
compatibility with various displays. For more details, please refer to the 6.3.4
Button Control User-defined on the page 16.

4K HDBaseT 2.0 Extender
11
6. RS232 Control
6.1 RS232 Connection
According the RS232 control mode, there are three types of RS232 connection for
different application.
①
When only control the local transmitter, please connect a control device (e.g. PC) to
the RS232 port of the transmitter, the connection diagram shown as below:
Po C IN
HD BT OU T
PC
Transmitter

4K HDBaseT 2.0 Extender
12
②
When control the far-end third party device from local control device (e.g. PC),
please connect the PC to the RS232 port of the transmitter, and then please
connect the third party device (e.g. projector) to the RS232 port of receiver. The
connection diagram shown as below:
PoC I N
HDB T OUT
Projector
RS232:
HDBT:
Receiver
Transmitter
PoC
PC
Power
RS232

4K HDBaseT 2.0 Extender
13
③
When control the local third party device from far-end control device (e.g. PC),
please connect the PC to the RS232 port of the receiver, and then please connect
the third party device to the RS232 port of transmitter. The connection diagram
shown as below:
PoC IN
HDBT O UT
PC
Third Party Device
RS232:
HDBT:
Receiver
Transmitter
PoC
Power
RS232

4K HDBaseT 2.0 Extender
14
6.2 RS232 Control Software
After set all needed input and output devices according to the RS232 connection
diagram, please install the RS232 control software into the control PC to send RS232
command.
l Installation: Copy the control software file to the control PC.
l Uninstallation: Delete all the control software files in corresponding file path.
Here take the software CommWatch.exe as an example.
First, please double-click the following icon:
Then, the interface of the control software is showed as below:
Parameter configuration area
Monitoring area, show the commands
and its feedback information.
Command sending area
Operation area

4K HDBaseT 2.0 Extender
15
Please set the parameters of COM number, bound rate, data bit, stop bit and the parity
bit correctly, then the RS232 commands can be sent in the Command Sending Area.
Baud rate: 2400, 4800, 9600, 19200, 38400, 57600 or 115200.
Data bit: 8.
Stop bit: 1.
Parity bit: none.
6.3 RS232 Command
Beside the button control on the front panel, the transmitter can be controlled by
sending the below commands.
Baud rate: 9600.
Data bit: 8.
Stop bit: 1.
Parity bit: none.
6.3.1 Signal Switching
Command
Function
Feedback Example
50701%
Switch to HDMI IN 1 input.
SWITCH TO HDMI1
50702%
Switch to HDMI IN 2 input.
SWITCH TO HDMI2
50710%
Enable auto-switching mode.
AUTO SWITCHING
50711%
Disable auto-switching mode.
MANUAL SWITCHING
50712%
Get the signal switching mode.
AUTO SWITCHING
MANUAL SWITCHING
6.3.2 CEC Command
Command
Function
Feedback Example
50730%
Volume up the display
CEC VOLUME INCREASE
50731%
Volume down the display
CEC VOLUME DECREASE
50732%
Mute the display
CEC VOLUME MUTE
50733%
Display ON
CEC DISPLAY ON
50734%
Display OFF
CEC DISPLAY OFF
Note: The display must support CEC.