Woxcon CE-EX50 User manual

CE-EX50
1
CE-EX50
HDMI Extender over single
50m Cables with IR Control
User Manual
VER: 1.1

CE-EX50
2
Thank you for purchasing this product. For optimum performance and safety, please
read these instructions carefully before connecting, operating or adjusting this
product. Please keep this manual for future reference.
Table of Contents
1. Introduction ....................................................................................................... 3
2. Package Contents ............................................................................................... 4
3. Features ............................................................................................................. 4
4. Specifications ..................................................................................................... 5
5. Panel descriptions .............................................................................................. 6
5.1 Transmitting unit ........................................................................................ 6
5.2 Receiver unit .............................................................................................. 7
5.3 RX Equalizer distance adjust ....................................................................... 8
6. Connection diagram ........................................................................................... 9
7. Connect and Operate ........................................................................................ 10
8. Wideband IR (30KHz---60KHz) introduction ....................................................... 11

CE-EX50
3
1. Introduction
The HDMI Extender over Single Cat5e/6 with IR extends high definition video and
audio signals and IR, at a distance of up to 164ft/50m over a single Cat5e/6 cable.
Features EDID management, which allows and encourages source and display
“handshake” for seamless integration. With only one cost effective Cat5e/6 cable,
high definition sources with HDMI outputs can be connected to high definition
displays with HDMI inputs over long distances. Deep color video, DTS-HD or Dolby
TrueHD audio is supported and compatible with the extender. In addition, the
extender is also equipped with bi-directional IR pass-through which allows for source
or display control.
The extender includes two units: transmitting unit and receiving unit. The
transmitting unit is used to capture the HDMI input with IR signals and carries the
signals via one cost effective Cat5e/6 cable. The receiving unit is responsible for
equalizing the transmitted HDMI signal and reconstructing IR control signals. The
extender offers the most convenient solution for HDMI extension over a single
Cat5e/6 with long distance capability, and is the perfect solution for any application.

CE-EX50
4
2. Package Contents
◆ HDMI Transmitter...........................................................................................1PCS
◆ HDMI Receiver...............................................................................................1PCS
◆ Windband IR Tx cable....................................................................................1PCS
◆ Windband IR Rx cable....................................................................................1PCS
◆ 5V1A DC Power Supply Adaptor.....................................................................1PCS
◆ Product Manual..............................................................................................1PCS
3. Features
• Allows HDMI Audio/Video and IR signals to be transmitted over a single
Cat5e/6 cable.
• Supportcopy EDID from receiver display or loop out display.
• Allows for cascading via additional HDMI loop out port.
• Support Power over cable function.
• Transmission Range: Extends 1080p resolution up to 164ft/50m over a
single Cat5e or Cat6 cable.
• Works with HDMI and HDCP compliant devices.
• Supports up to 1080p High Definition resolution.
• Compact design for an easy and flexible installation.

CE-EX50
5
4. Specifications
Video Bandwidth: Single-link 165Mhz [ 4.95Gbps]
Video Support: 480i/480p/720p/1080i/1080p @60
Audio Support: Surround Sound (up to 7.1 ch) or stereo digital audio
Transmission Range: HD [1080p 24-bit color] – up to 50m [164ft]
Input TMDS Signal: 3.3 volts
Input DDC Signal: 5.0 volts/P-P
ESD Protection: Human Body model: +/- 8 kV (air-gap discharge)
+/- 4 kV (contact discharge)
HDMI connector: Type A 19 pin female
RJ-45 connector: WE/SS 8P8C
3.5mm connector: (TX and RX) IR Receiver/IR Blaster
MECHANICAL SPECS
Housing: Metal enclosure
Power Supply: (1) 5V1A DC
Power consumption:1.5 watts (TX); 1.0 watts (RX)
Operation temperature: 32~104 °F
Storage temperature: -4 ~140 °F
Relative humidity: 20~90 % RH (no condensation)

CE-EX50
6
5. Panel descriptions
5.1 Transmitting unit
① HDMI in: This slot is where you connect the HDMI output port of your source
equipment such as DVD/Blu-ray players or Set-Top-Box with an HDMI cable.
② EDID: The switcher can switch copy EDID function,switch to right position,the
extender will copy hdmi loop out display EDID information to source. Switch to
left position,the extender will copy Receiver display EDID to sourc.
③ HDMI out:This slot is to connect the HDMI input of your display such as an HDTV.
④ IR out: Connect the IR Blaster cable included in the package for IR signal
transmission. Pace the IR blaster in direct line-of-sight of the equipment to be
controlled.
⑤ Power LED: This LED will illuminate when the device is connected with power
supply.
⑥ CAT:Connect the CAT output of the transmitter with the CAT input of the receiver
with CAT5E/6 cable.
⑦ Link LED: This LED will illuminate when the device is connected to HDMI source.
⑧ DC 5V: Connect from 5V DC power supply into the unit and connect the adaptor
to an AC outlet.

CE-EX50
7
5.2 Receiver unit
① EQ switcher: HDMI Receiver equalizer switcher.
② HDMI out: This slot is to connect the HDMI input port of your display such as an
HDTV.
③ IR in: Connect to the IR Receiver for IR signal reception. Ensure that remote
being used is within the direct line-of-sight of the IR receiver.
④ Power LED: This LED will illuminate when the device is connected with power
supply.
⑤ CAT:Connect the CAT input of the receiver with the CAT output of the transmitter
with CAT5E/6 cable.
⑥ Lock LED:This LED will illuminate when the HDMIsignal from the transmitter is
stable.

CE-EX50
8
5.3 RX Equalizer distance adjust
If you see flickering or blinking image on the display, adjust the EQ switch to
improve the cable skew. MAX stands for the strongest HDMI signal level for the
longest possible transmission length while MIN stands for the weakest HDMI signal
level for short transmission length. Adjust the signal level from MIN to MAX until
desired video quality is displayed.
Recommended EQ setting
Position
Cable Length
under 15m (49.5ft)
15-30m (49.5 ft - 99ft)
30-40m (99ft - 132ft)
40-50m(132ft – 164ft)

CE-EX50
9
6. Connection diagram

CE-EX50
10
7. Connect and Operate
1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or
Satellite Receiver, etc. to the HDMI input on the Transmitting unit.
2. Connect a display such as an HDTV or HD Projector to the HDMI output on the
Receiving unit.
3. Connect a single Category 5e/6 up to 164ft/50m to the output of the Transmitting
unit, and the other end to the input of the Receiving unit.
4. For power, plug both the Transmitting unit and Receiving unit with the included
power supplies.
5. Power on each device in the same sequence (receiver and transmitter will already
be powered when either unit is plugged in.)
At this point the display connected should display the source signal connected to the
extender set. If no signal is being displayed, check the receiver EQ swithcer. If a
display is having difficulty receiving a signal, see EDID section and perform EDID
learning or access the display’s menu and adjust the resolution (lowest to highest
until signal is displayed). A 24 Hz vertical refresh rate may work better than 60 Hz or
higher. Use the source remote at the receiver emitter to test IR functionality. If the
IR remote function is not responding, check the emitters to ensure they are placed
correctly and are plugged into the correct IR jacks on the Extender set receiving and
transmitting units.

CE-EX50
11
8. Wideband IR (30KHz---60KHz) introduction
IR BLASTER (TX)
To control the source: Plug IR Blaster into IR TX port of transmitter unit; place
blaster in front of the IR eye of the source.
To control the display: Plug IR Blaster into IR TX port of receiver unit; place blaster
in front of the IR eye of the display.
IR RECEIVER (RX)
To control the source: Plug IR Receiver into IR RX port of receiver unit; place
receiver at or near display.
To control the display: Plug IR Receiver into IR RX port of transmitter unit; place
receiver in position where it is able to receive remote signals

CE-EX50
12