Wyrestorm SP-0104-H2 User manual

PDF provided by Conference Room AV
WyreStorm SP-0104-H2 1x4 4K HDMI Splitter w/ HDMI 2.0 & HDCP 2.2

1x4 or 1x8 4K HDMI Splitter
with HDCP 2.2 Encryption
SP-0104-H2 | SP-0108-H2 Quickstart Guide
In the Box
1x SP-0104-H2 or SP-0108-H2 Splitter
1x 12V DC 1A Power Supply
1x 3-pin Screw Down Phoenix Connector
2x Mounting Brackets
1x Quickstart Guide
Basic Wiring Diagram
KEY
HDMI
Power
12V DC 1A
Power Supply
UHD Display
UHD Display UHD Display
UHD Display
HDMI to
display
HDMI to
display
UHD Source
HDMI to
display
IMPORTANT!
Do not connect or disconnect (hot plug) the HDMI connections while
the splitter is powered on. Doing so may cause damage to the units or
connected devices.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of
this product. Refer to the Installation Guide and other documentation on
the product page for additional information.
Before Beginning
• WyreStorm recommends visiting the product page before installing
this product for updates to this Quickstart Guide as well as other
information about the product.
• Verify that all items are included in the packaging per the In the Box
list.
Installation
1. Connect an HDMI source to the HDMI In on the splitter using an
HDMI cable from a high quality brand such as WyreStorm Express.
2. Connect HDTV displays to Output 1 using an HDMI cable from a
high quality brand such as WyreStorm Express.
3. Repeat step 2 for additional displays or additional splitters.
4. Connect the included 12V DC 1A power supply to the DC 12V jack.
5. Congure EDIDs per the EDID Settings section.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
SP-0104-H2 | SP-0108-H2 Quickstart Guide | 151023
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Pure HDMI 1x4 or 1x8 splitter with support for full 4K resolutions and HDCP 2.2.

Front Panel
Rear Panel
Input LED Solid: HDMI source is connected and powered On.
Off: HDMI source is not connected or is powered Off.
Output LEDs
SP-0104-H2: 1-4 | SP-108-H2: 1-8
Solid: Display is connected and powered On.
Off: Display is not connected or is powered Off.
Power LED Solid: The splitter is powered On
Off: The splitter is powered Off
Power In 5.5mm Male Barrel Jack
Connect to the included 100~240V AC 50/60Hz power supply.
HDMI Outputs
19-pin type A HDMI female:
SP-0104-H2: 1-4 | SP-108-H2: 1-8
Supports HDMI and DVI/D (requires adapter-not included). Limited to 600MHz pixel clock.
Input 19-pin type A HDMI female:
Supports HDMI and DVI/D (requires adapter-not included). Limited to 600MHz pixel clock.
EDID
Rotary Dial
Used to set EDIDs to correct resolution conflicts between the source and the display.
See EDID Settings.
RS-232 3-pin Screw Down Phoenix Connector
Used to update rmware on the SP-0104-H2. See RS-232 Wiring.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
SP-0104-H2 | SP-0108-H2 Quickstart Guide | 151023
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
2 of 4

HDMI Wiring
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables,
and electrical or environmental interference can have an adverse effect
on HDMI transmission limiting performance. Steps should be taken to
minimize these factors (or remove completely) during installation for
best results.
• WyreStorm recommends using HDMI cables from a high quality brand
such as WyreStorm Express.
• Active HDMI cables or extenders must be used for distances greater
than 10m between the splitter and connected devices in order to
maintain the highest level of video performance.
RS-232 Wiring
RS-232 Connection Guidelines
The following wiring diagram shows the pinouts for the extender set.
While not shown, connect the TX (transmit) to RX (receive) pins at the
control system or PC side of the cable.
Most control systems and computers are DTE where pin 2 is RX, this can
vary from device to device. Refer to the documentation for the connected
device for pin functionally to ensure that the correct connections can be
made.
Pin 1:
Pin 2:
Positive (+)
Negative (-)
Pin 3: Ground (GND)
Wire colors shown are for pin identificaiton only and do not
represent any wiring standard.
1 2 3
EDID Settings
EDIDs can be congured to resolve issues with video output on displays
that may not accept the maximum resolution available from the source.
Note:
• Ensure that a display is connected and powered On to the selected
output before copying EDIDs or the copy will fail. When this occurs,
EDID will be set to 4K@30Hz 2ch.
• Power to the splitter must be cycled (Off/On) after changing dip
switches in order for the setting to take effect.
Position Video Resolution and Audio
0Copy EDID from HDMI output1 (default setting)
1 1080i 2ch
21080i Dolby/DTS 5.1ch
3 1080i, HD Audio
4 1080p 2ch
51080p Dolby/DTS 5.1ch
61080p HD Audio
73D 2ch
83D Dolby/DTS 5.1ch
9 3D HD Audio
A 1280x1024 DVI
B 1920x1080 DVI
C 1920x1200 DVI
D 4K@30HZ 2ch
E 4K@60HZ 2ch
FCopy EDID from HDMI output2
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
SP-0104-H2 | SP-0108-H2 Quickstart Guide | 151023
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
3 of 4

Warranty Information
This product is covered by a 2 year limited parts and labor warranty. During this period there will be no charge for unit
repair, component replacement or complete product replacement in the event of malfunction. The decision to repair
or replace will be made by the manufacturer. This limited warranty only covers defects in materials or workmanship
and excludes normal wear and tear or cosmetic damage.
Visit the product page located at wyrestorm.com for additional information on this product including important
technical information not provided in this document and warranty terms & conditions.
Specications
Audio and Video
Inputs 1x HDMI 19-pin type A female
Outputs
4x HDMI 19-pin type A female
(SP-0104-H2)
8x HDMI 19-pin type A female
(SP-0108-H2)
Audio Formats 2ch and Up to Dolby/DTS 5.1ch
Video Resolution (Max) 1920x1080@60Hz (1080p60)
4096x2160p@60Hz 4:2:0 (4K)
Color Depth 1080p: 48bit Deep Color | 4K: 24bit
Maximum Pixel Clock 600MHz
Communication and Control
HDMI HDCP 2.2 | EDID DVI/D with adapter (not
included)
RS-232 1x 3-pin Phoenix Connector
Firmware Update Only
Power
Power Supply 12V DC 1A
Max Power Consumption SP-0104-H2: 4W (4K@60Hz)
SP-0108-H2: 6W (4K@60Hz)
Environmental
Operating Temperature 32°F ~ 113°F (0°C ~ 45°C)
10% ~ 90%, non-condensing
Storage Temperature -4°F ~ 140°F (-20°C ~ 70°C)
10% ~ 90%, non-condensing
Maximum BTU SP-0104-H2: 71.65 BTU/hr
SP-0108-H2: 95.53 BTU/hr
Dimensions and Weight
SP-0104-H2 SP-0108-H2
Height 18mm/0.71in 18mm/0.71in
Width 167.2mm/6.59in 257.2mm/10.13in
Depth 69.7mm/2.75in 89.7mm/3.54in
Weight 0.32kg/0.7lbs 0.58kg/1.28lbs
Regulatory
Safety and Emission CE | FCC | RoHS
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the splitter, sources, and display
devices.
• Verify that the splitter supports the output resolution of the source.
• Verify that the splitter and display devices support the output
resolution of the source.
• Congure EDID Settings to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K
rated.
• Verify that all source and HDBaseT connections are not loose and are
functioning properly.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable
to other devices to verify functionality.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
SP-0104-H2 | SP-0108-H2 Quickstart Guide | 151023
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
4 of 4