Wyrestorm SP-0108-SCL User manual

SP-0108-SCL
4K60 1:8 HDMI Splitter
Quickstart Guide
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
IMPORTANT! Installation
• Read through the Wiring and Connections section for important
wiring guidelines before creating or choosing premade cables.
• While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication.
• Visit the product page to download the latest rmware, document
version, additional documentation, and conguration tools.
Copyright © 2022 WyreStorm Pro AV Corporation |wyrestorm.com
SP-0108-SCL Quickstart Guide | 220518 1 of 2 INT: [phone] | US: 844.280.WYRE (9973) [email protected]
In the Box
1x SP-0108-SCL Splitter
1x DC 12V PSU (US/UK/EU/AU)
2x 3-Pin Terminal Block
2x Wall Mounting Brackets (with Screws)
1x Quickstart Guide (This Document)
Basic Wiring Diagram
Warranty Information
WyreStorm Technologies ProAV Corporation warrants that its products to be free from defects in material and workmanship under normal use
for a period of ve (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited
product warranty.
KEY
HDMI
Power
Digital Audio
Power Supply
UHD Source
UHD Display 1080p Display
UHD Display UHD Display
1080p Display UHD Display
1080p Display UHD Display
Amplier
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the device.
• Verify that all HDMI connections are not loose and are functioning properly.
• Verify that the output resolution of the source and display is supported by
this device.
• Congure EDID Settings to a lower resolution.
• If transmitting 4K, verify that the HDMI cables used are 4K rated.
No or Intermittent 3rd party Device Control
• Verify that the RS-232 cables are properly terminated.
Troubleshooting Tips
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.

IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable transmitters, kinks in cables, and
electrical or environmental interference will have an adverse effect on signal
transmission which may limit performance. Steps should be taken to
minimize or remove these factors completely during installation for best
results.
• WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its
entirety before running or terminating any wires to ensure proper operation and to avoid damaging the equipment.
Note: HDMI signal transmission distance can be increased to up to 50m/164ft
by using WyreStorm’s Hybrid Active Optical cables.
EDID Management
This device equips a 4-pin DIP switch for EDID management, including copy mode, xed mode and customized mode. The DIP Switch settings and the
corresponding functions are as follows:
Downscaler Settings
Downscaler dipswitches 1-8 correspond to HDMI outputs 1-8 respectively.
Up Position: The down scaler of the corresponding output is off.
Down Position: The down scaler of the corresponding output is on (default).
3-Pin Digital Audio
Copyright © 2022 WyreStorm Pro AV Corporation |wyrestorm.com
SP-0108-SCL Quickstart Guide | 220518 2 of 2 INT: [phone] | US: 844.280.WYRE (9973) [email protected]
3rd Party Device
Pin 1 L (Left Signal) ---> To ---> Left Signal (L+)
Pin 2 R (Right Signal) ---> To ---> Right Signal (R+)
Pin 3 GND (Ground) ---> To --->
Left Ground (L-)
Right Ground (R-)
WyreStorm Connector
RS-232 Wiring
The SP-0108-SCL uses a 3-pin RS-232 with no hardware flow control. Most
control systems and computers are DTE where pin 2 is RX, this can vary from
device to device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
Communication Connections
3rd Party Device
Pin 1 TX (Transmit) ---> To ---> RX (Receive)
Pin 2 RX (Receive) ---> To ---> TX (Transmit)
Pin 3 G (Ground) ---> To ---> G (Ground)
WyreStorm Connector
EDID Descriptions
Copy mode
(Default)
Default: Copy output 1.
Users can use EDID COPY buttons or API
commands to copy EDID of the displays connected
with any output port in this mode.
Fixed EDID:
4K@60Hz 4:4:4
7.1CH with HDR
Support HLG and HDR10;
Support PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby
Atmos, DTS-HD Master Audio and DTS:X.
Fixed EDID:
4K@60Hz 4:4:4
5.1CH with HDR
Support HLG and HDR10;
Support PCM 2.0/5.1, Dolby Digital and DTS 5.1.
Fixed EDID:
4K@60Hz 4:4:4
2.0CH with HDR
Support HLG and HDR10;
Support PCM 2.0 only.
Fixed EDID:
4K@60Hz 4:2:0
7.1CH with HDR
Support HLG and HDR10;
Support PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby
Atmos, DTS-HD Master Audio and DTS:X
Fixed EDID:
4K@60Hz 4:2:0
5.1CH with HDR
Support HLG and HDR10;
Support PCM 2.0/5.1, Dolby Digital and DTS 5.1.
Fixed EDID:
4K@60Hz 4:2:0
2.0CH with HDR
Support HLG and HDR10;
Support PCM 2.0 only.
Fixed EDID:
1080P@60Hz
7.1CH
Support PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby
Atmos, DTS-HD Master Audio and DTS:X.
EDID Descriptions
Fixed EDID:
1080P@60Hz
5.1CH
Support PCM 2.0/5.1, Dolby Digital and DTS 5.1.
Fixed EDID:
1080P@60Hz
2.0CH
Support PCM 2.0 only.
Fixed EDID:
1080i@60Hz
7.1CH
Support PCM 2.0/5.1/7.1, Dolby TrueHD, Dolby
Atmos, DTS-HD Master Audio and DTS:X
Fixed EDID:
1080i@60Hz
5.1CH
Support PCM 2.0/5.1, Dolby Digital and DTS 5.1.
Fixed EDID:
1080i@60Hz
2.0CH
Support PCM 2.0 only.
Fixed EDID: DVI
1920x1200@60
no audio
No audio
Fixed EDID: DVI
1280x1024@60
no audio
No audio
Customized EDID Users can upload their own EDID les through API
commands or PC tools. If no EDID is uploaded, a
default EDID (4K@60Hz 4:4:4 2ch with HDR/HLG
support) will be used in this mode.