Wyrestorm NHD-0401-MV User manual

NHD-0401-MV
4-Input 4K60 Multiview Processor for NetworkHD™
Quickstart Guide
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
IMPORTANT! Installation Requirements
• Read through the Wiring and Connections section for important wiring
guidelines before creating or choosing premade cables.
• Visit the product pages to download the latest rmware, document version,
additional documentation, and conguration tools.
Copyright © 2022 WyreStorm Technologies | wyrestorm.com
NHD-0401-MV Quickstart Guide | 221021 1 of 2 INT: [phone] | US: 844.280.WYRE (9973) [email protected]
In the Box
1x NHD-0401-MV Switcher
1x 12V 2A Power Supply (US/UK/EU/AU)
1x IR Remote
1x IR Receiver Cable
2x Wall Mounting Brackets
2x Rack Mounting Brackets
1x Quickstart Guide (This Document)
Wiring Diagram - NetworkHD Solution
Wiring Diagram - Standalone Solution

Copyright © 2022 WyreStorm Technologies | wyrestorm.com
NHD-0401-MV Quickstart Guide | 221021 2 of 2 INT: [phone] | US: 844.280.WYRE (9973) [email protected]
RS-232 and IP Settings
Baud Rate: 115200
Data Bits: 8bits
Parity: None
Stop Bits: 1bit
Flow Control: None
Default IP Address: DHCP
Default IP Port: 23
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable transmitters, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken to
minimize or remove these factors completely during installation for best
results.
• WyreStorm recommends using pre-terminated VGA, HDMI, DP and USB
cables due to the complexity of these connector types. Using pre-
terminated cables will ensure that these connections are accurate and will
not interfere with the performance of the product.
RS-232 Wiring
The NHD-0401-MV uses a 3-pin RS-232 with no hardware flow control. Most
control systems and computers are DTE where pin 2 is RX, this can vary from
device to device. Refer to the documentation for the connected device for pin
functionally to ensure that the correct connections can be made.
Setup and Conguration
The NHD-0401-MV is designed to work natively with the NHD-CTL-PRO for
management, setup and congurations. However, the NHD-0401-MV can also
be used as a standalone multiview switcher.
Setup via the NHD-CTL-PRO
The NHD-CTL-PRO will automatically locate and display the NHD-0401-MV in
its web interface. Ensure that the NHD-CTL-PRO and NHD-0401-MV are in the
same IP address range.
Setup as a Standalone Switcher
The NHD-0401-MV contains a web interface that can be accessed directly by
entering it’s IP address into a web browser. The switcher can also be
controlled via API commands from a 3rd-party control system. Communication
settings are listed.
Communication and Connections
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its
entirety before running or terminating any wires to ensure proper operation and to avoid damaging the equipment.
Audio Connections
The audio connection uses a 3.5mm (1/8in) TRS stereo jack.
Tip:
Ring:
Left Channel
Right Channel
Sleeve: Ground (GND)
Warranty Information
WyreStorm Technologies ProAV Corporation warrants that its products to be free from defects in material and workmanship under normal
use for a period of ve (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our
limited product warranty.
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the switcher
• Verify that all HDMI connections are not loose and are functioning properly.
• Verify that the output resolution of the source and display is supported by
this switcher.
• Congure EDID Settings to a lower resolution.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
No or Intermittent 3rd party Device Control
Verify that the IR, LAN or RS-232 cables are properly terminated.
NHD-CTL-PRO Won’t Find Switcher
• Verify that both the switcher and controller are in the same IP address range
• Ensure rmware is update to date
3rd Party Device
Pin 1 TX (Transmit) ---> To ---> RX (Receive)
Pin 2 RX (Receive) ---> To ---> TX (Transmit)
Pin 3 G (Ground) ---> To ---> G (Ground)
WyreStorm Connector