Wyrestorm EX-40-G2 User manual

PDF provided by Conference Room AV
WyreStorm EX-40-G2 1080P HDMI Thin Extender Kit with 2-Way IR - 131'

HDMI over UTP Low Prole Extender Set
with 2-way (40m/131ft)
EX-40-G2 Quickstart Guide
In the Box
1x EX-40-G2 Transmitter
1x EX-40-G2 Receiver
2x 12V DC 0.5A Power Supply
2x 2-pin Screw Down Phoenix Connectors
2x Wide-band IR Emitters
1x Wide-band IR Receivers (30-50KHz)
1x Dual-band IR Receivers
4 x Mounting Brackets (1pr for TX and 1pr for RX)
1x Quickstart Guide
Basic Wiring Diagram
IMPORTANT!
Do not connect or disconnect (hot plug) the HDMI or UTP connections
while the transmitter or receiver is powered on. Doing so may cause
damage to the units or connected devices.
Additional Information
This Quickstart Guide provides the basic steps for the common uses of
this product. Refer to the Installation Guide and other documentation on
the product page for additional information.
Installation
Before Beginning
WyreStorm recommends visiting the product page before installing this
product for updates to this Quickstart Guide as well as other information
about this product.
Verify that all items are included in the packaging per the In The Box list.
Pre Wire
1. Run a Cat5e/6/6a cable from the transmitter location to the receiver
location. Terminate the cable per the UTP Wiring section.
2. (Optional) If using IR emitters or 3rd party connecting blocks at either
the transmitter or receiver, run the wire and terminate per the IR TX
(Emitter) Wiring section.
3. (Optional) If using IR receivers or an IR control system at either the
transmitter or receiver, run the wire and terminate per the IR RX
(Receiver) Wiring section.
Transmitter Installation
1. Connect an HDMI source to the HDMI In on the transmitter using an
HDMI cable from a high quality brand such as WyreStorm Express.
2. Using the cable created in Pre Wire step 1, connect the 8-pin RJ-45
female plug to the UTP Out jack on the transmitter.
3. (Optional) Place an IR emitter onto the source device near the
device’s IR sensor and connect the 3.5mm (1/8in) Mono Plug to the
IR TX port.
4. (Optional) Connect the 3.5mm (1/8in) stereo plug from an IR receiver
to the transmitters IR RX port.
Note: Use the included IR receiver labeled dual-band for devices
that use dual-band IR.
· If using a control system, refer to IR RX (Receiver) Wiring for
important wiring guidelines.
5. Connect the included 12V DC 0.5A power supply to the DC 12V
jack.
Receiver Installation
1. Connect the HDMI Out on the receiver to an input on the display
using an HDMI cable from a high quality brand such as WyreStorm
Express.
2. Using the cable created in Pre Wire step 1, connect the 8-pin RJ-45
female plug to the UTP In jack on the receiver.
3. (Optional) Place an IR emitter onto the display device near the
device’s IR sensor and connect the 3.5mm (1/8in) Mono Plug to the
IR TX port.
4. (Optional) Connect the 3.5mm (1/8in) stereo plug from an IR receiver
to the receivers IR RX port.
Note: Use the included IR receiver labeled dual-band for devices
that use dual-band IR.
If using a control system, refer to IR RX (Receiver) Wiring for
important wiring guidelines.
5. Connect the included 12V DC 0.5A power supply to the DC 12V
jack.
Copyright © 2015 WyreStorm Technologies | wyrestorm.com
EX-40-G2 Quickstart Guide | 151013
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
HDMI over UTP extender set, allowing extension of HDMI and IR control over 40m/131ft of Cat6 cable.
IR Emitter
IR EmitterIR Receiver
HDMI Source
HDMI Display
KEY
HDMI
UTP Cat5e/6
IR TX and RX
Power
EX-40-G2 Transmitter (TX)
EX-40-G2 Receiver (RX)
12V DC 0.5A
Power Supply
HDMI
UTP
Cat5e/6/6a IR to Control System
CAB-IR-LINK (Sold Separately)
HDMI

Copyright © 2015 WyreStorm Technologies | wyrestorm.com
EX-40-G2 Quickstart Guide | 151013
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
2 of 4
Front Panel (TX/RX)
EX-40-G2 TX EX-40-G2 TX
EX-40-G2 RX EX-40-G2 RX
Rear Panel (TX/RX)
Power LED Solid: The transmitter is powered On
O: The transmitter is powered O
Status LED
Flashing: The transmitter is operating
normally
O: The transmitter is Not operating
normally
Power In
5.5mm Male Barrel Jack
2-pin Screw Down Phoenix Connector
Connect to the included 12V DC 0.5A
power supply. See Power Supply Wiring.
UTP Out (TX)
UTP In (RX)
8-pin RJ-45 female
Connect the transmitter UTP Out to
receiver UTP In using the cable created in
Pre Wire step 1.
IR TX/RX
3.5mm (1/8in) Mono Plug
IR TX: Connect to the supplied IR emitter
to control a local device from the remote
display location via HDBaseT.
IR RX: Connect to the supplied IR receiver
to send IR to the remote display via
HDBaseT.
See IR Wiring for important connection
information.
HDMI In (TX)
HDMI Out (RX)
19-pin type A HDMI female digital video/
audio: Supports HDMI and DVI/D (requires
adapter-not included). Limited to 297MHz
pixel clock
EDID Settings (TX)
EQ (RX)
Rotary Dial:
EDID: Used to set EDIDs to correct
resolution conicts between the source
and the display. See EDID Settings.
EQ: Used to ne tune the performance of
the UTP signal based on the length of the
cable. See UTP Distance Settings.

Copyright © 2015 WyreStorm Technologies | wyrestorm.com
EX-40-G2 Quickstart Guide | 151013
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
3 of 4
UTP Wiring
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables,
and electrical or environmental interference can have an adverse eect
on UTP transmission limiting performance. Steps should be taken to
minimize these factors (or remove completely) during installation for
best results.
Wiring for HDBaseT follows the EIA T568B standard.
Pin 1
Pin 8
Wire colors shown follow EIA/TIA-568B standard.
Pin 1:
Pin 2:
Pin 3:
Pin 4:
Pin 5:
Pin 6:
Pin 7:
Pin 8:
White/Orange
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
Supported Video Resolutions
The type of category cable used and the distance between the transmitter
and receiver can restrict the available video resolution.
Cable Type Range Supported Resolution
Cat5/5e/6 70m/230ft Up to 1080p@60Hz 3D
Power Supply Wiring
The power supply may be connected using the attached 5.5mm barrel
connector or using the supplied 2-pin Screw Down Phoenix Connector.
Wire colors shown are for pin identificaiton only and do not
represent any wiring standard.
Pin 1:
Pin 2:
PWR - (GND)
PWR + (Positive)
1 2
IR Wiring
IR TX (Emitter) Wiring
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
Tip: IR Signal
Sleeve: Ground (GND)
IR RX (Receiver) Wiring
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that
outputs +5V DC to power the included IR receiver.
IMPORTANT! IR TX Connection Guidelines
· 3rd party IR receivers may require a dierent voltage, refer to the
documentation provided with the IR receiver before making any
connections to avoid damaging the device.
· When connecting to an IR control system use the WyreStorm CAB-IR-
LINK stereo to mono cable to remove the sleeve +5V DC.
Tip:
Ring: IR Signal
+5V DC
Sleeve: Ground (GND)
EDID Settings
EDIDs can be congured to resolve issues with video output on displays
that may not accept the maximum resolution available from the source.
1080p 2ch 0
1080p 5.1ch 1
EDID Copy Mode
(Copy EDID from display) 2
1080i 2ch 3
1080p 2ch
Long Cable mode (LC mode) 4
1080p 5.1 LC mode 5
EDID Copy Mode LC mode 6
1080i 2ch LC mode 7
UTP Distance Settings
Adjust the dial based on the distance (cable length) between the
transmitter and receiver.
0-10m transmission distance 0 to 1
10-30m transmission distance. Default is 4. 2 to 5
30-40m transmission distance 6 to 7
Reserved 8 to F

Copyright © 2015 WyreStorm Technologies | wyrestorm.com
EX-40-G2 Quickstart Guide | 151013
North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343
[email protected]
Warranty Information
This product is covered by a 2 year limited parts and labor warranty. During this period there will be no charge for unit
repair, component replacement or complete product replacement in the event of malfunction. The decision to repair or
replace will be made by the manufacturer. This limited warranty only covers defects in materials or workmanship and
excludes normal wear and tear or cosmetic damage.
Visit the product page located at wyrestorm.com for additional information on this product including important
technical information not provided in this document and warranty terms & conditions.
4 of 4
Audio and Video
Audio Formats 2ch analog and Up to 7.1 DTS Master HD
and Dolby True HD
Video Resolution Up to 1080p@60Hz 3D
Color Depth 24bit
Maximum Pixel Clock 297 MHz
Communication and Control
UTP EDID | Bi-directional IR
HDMI EDID | DVI/D supported with adapter (not
included)
IR Bi-directional over UTP
Power
Power Supply Input: 100~240V AC 50/50Hz
Output: 12V DC 0.5A
Max Power
Consumption
5W
Environmental
Operating Temperature 32°F ~ 113°F (0°C ~ 45°C)
10% ~ 90%, non-condensing
Storage Temperature -4°F ~ 140°F (-20°C ~ 70°C)
10% ~ 90%, non-condensing
Dimensions and Weight
Height 17mm/0.67in
Width 127mm/5in
Depth 53.8mm/2.12in
Weight 0.3kg/0.66lbs
Regulatory
Safety and Emission CE | FCC
RoHS Compliant
Specications Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the transmitter and receiving
device and that both devices are powered on.
• Verify that the transmitter supports the output resolution of the source.
See Supported Video Resolutions.
• Verify that the receiving device and display support the output resolution
of the source.
- Congure EDID Settings to a lower resolution.
- Adjust UTP Distance Settings based on the length of the cable
between the transmitter and receiver.
• If transmitting 3D, verify that the HDMI cables used are 3D rated.
• Verify that the UTP cable is properly terminated per the UTP Wiring
section.
• Verify that all source and UTP connections are not loose and are
functioning properly.
No or Intermittent 3rd party Device Control
• Verify that the IR cable(s) is properly terminated. See IR Wiring.
• Verify that the IR emitter is located near the IR sensor on the device.
• Verify that the IR receiver labeled dual-band is being used with dual-
band IR devices.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable
to other devices to verify functionality.
• Use a ashlight to locate the IR receiver behind any tinted panels on the
device being control.