Xantrex RS3000 User manual

RS3000 Sine Wave Inverter/Charger
Operation Guide
RS3000

RS3000 Sine Wave Inverter/Charger
Operation Guide

About Xantrex
Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from
50 watt mobile units to one MW utility-scale systems for wind, solar, batteries, fuel cells, microturbines, and backup
power applications in both grid-connected and stand-alone systems. Xantrex products include inverters, battery
chargers, programmable power supplies, and variable speed drives that convert, supply, control, clean, and distribute
electrical power.
Trademarks
RS3000 Sine Wave Inverter/Charger is a trademark of Xantrex International. Xantrex and Xanbus are registered
trademarks of Xantrex International.
Other trademarks, registered trademarks, and product names are the property of their respective owners and are used
herein for identification purposes only.
Notice of Copyright
RS3000 Sine Wave Inverter/Charger Operation Guide © December 2004 Xantrex International. All rights reserved.
Disclaimer
UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX TECHNOLOGY INC. (“XANTREX”)
(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY
TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.
(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT,
INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH
INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK.
Date and Revision
December 2004 Rev B
Part Number
975-0170-01-01
Contact Information
Telephone: [phone] (toll free North America)
1 360 925 5097 (direct)
Fax: [phone] (toll free North America)
1 360 925 5143 (direct)
Email: [email protected]
Web: www.xantrex.com

975-0170-01-01 iii
About This Guide
Purpose
The RS3000 Sine Wave Inverter/Charger Operation Guide provides
explanations and procedures for operating, configuring, and
troubleshooting the RS3000 Sine Wave Inverter/Charger (RS3000).
Scope
The guide provides safety guidelines and information about operating,
configuring, and troubleshooting the unit. It does not include information
for installing the inverter/charger. Refer to the RS3000 Sine Wave
Inverter/Charger Installation Guide.
The guide also provides general guidelines on batteries; it does not
provide details about particular brands of batteries. You need to consult
individual battery manufacturers for this information.
Audience
The guide is intended for users who need to configure and operate the
RS3000 Sine Wave Inverter/Charger.
Organization
This guide is organized into four chapters and three appendixes.
Chapter 1, “Introduction”, outlines the main performance and safety
features of the RS3000 Sine Wave Inverter/Charger. Reading this chapter
will give you a clear understanding of the inverter/charger’s capabilities.
Chapter 2, “Operation”, provides information about operating the
RS3000. Details are provided on how to read the front panel indicators to
monitor the RS3000.
Chapter 3, “Configuration”, explains how to configure the RS3000 from
the control panel.

About This Guide
iv 975-0170-01-01
Chapter 4, “Troubleshooting”, explains how to identify and solve
problems that can occur with the RS3000.
Appendix A, “Specifications”, provides electrical, physical, and
performance specifications for the inverter/charger.
Appendix B, “Battery Charging Reference”, provides information on
three-stage charging, two-stage charging, and charging times.
Appendix C, “Terminology”, provides a glossary and a listing of
commonly used abbrevations and acronyms.
“Warranty and Return Information” provides the product warranty,
explains how to return a product for service, and describes what to
prepare for a call to Xantrex Customer Service.
Conventions Used
The following conventions are used in this guide.
WARNING
Warnings identify conditions or practices that could result in personal injury or
loss of life.
CAUTION
Cautions identify conditions or practices that could result in damage to the
RS3000 or other equipment.
Important: Important notes provide information that is important for you
to know. They are not as critical as Cautions or Warnings.

About This Guide
975-0170-01-01 v
Symbols Used
The following symbols are used on the product labels or in this guide.
Related Information
For related materials on this product and its available accessories, see:
RS3000 Sine Wave Inverter/Charger Installation Guide (975-0171-01-01)
System Control Panel Owner’s Guide (975-0083-01-01)
Automatic Generator Start Owner’s Guide (975-0082-01-01)
Xanbus System Installation Guide (975-0136-01-01)
More information about Xantrex Technology Inc. as well as its products
and services, including a complete list of Xanbus-enabled devices, is
available at www.xantrex.com
Contact Information
!In this guide: Important information, warnings or cautions.
On the product: Important information, warnings or cautions with
further explanation in the product guides.
"AC – Alternating current
#DC – Direct current
$Warning: Hot surface. Do not touch.
%DC ground connection point
&AC safety ground connection point from incoming AC source
'AC safety ground connection point for AC output (to AC loads)
Telephone: [phone] (toll free North America)
1 360 925 5097 (direct)
Fax: [phone] (toll free North America)
1 360 925 5143 (direct)
Email: [email protected]
Web: www.xantrex.com

vi

975-0170-01-01 vii
Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS
The RS3000 Sine Wave Inverter/Charger Operation Guide contains
important safety instructions.
Before you install and use your RS3000 Sine Wave Inverter/Charger, be
sure to read, understand and save these safety instructions and those in the
other product guides.
Read all instructions and cautionary markings on the Inverter/Charger, the
batteries and all appropriate sections of this guide.
1. Use of accessories not recommended or sold by Xantrex Technology,
Inc. may result in a risk of fire, electric shock, or injury to persons.
2. The Inverter/Charger is designed to be permanently connected to your
AC and DC electrical systems. Xantrex recommends that all wiring
be done by a certified technician or electrician to ensure adherence to
the local and national electrical codes applicable in your application.
3. To avoid a risk of fire and electric shock, make sure that existing
wiring is in good condition and that wire is not undersized. Do not
operate the Inverter/Charger with damaged or substandard wiring.
4. To reduce risk of damage and injury, charge only rechargeable
lead-acid batteries (flooded, gel, or absorbed glass mat (AGM) types).
Other types of batteries may burst, causing personal injury and
damage.
WARNING: Risk of injury or loss of life
The RS3000 Sine Wave Inverter/Charger shall not be used in connection with life
support systems or other medical equipment or devices.
WARNING
The following warnings identify conditions or practices that could result in
personal injury or loss of life.

Safety
viii 975-0170-01-01
5. Do not operate the Inverter/Charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way. If the unit is
damaged, see the “Warranty and Return Information” section in the
RS3000 Sine Wave Inverter/Charger Operation Guide.
6. Do not disassemble the Inverter/Charger; it does not contain user
serviceable parts. Take it to a qualified service person when service or
repair is required. Incorrect reassembly may result in a risk of
electrical shock or fire. Internal capacitors remain charged after all
power is disconnected. For instructions on obtaining service, see the
“Warranty and Return Information” section in the RS3000 Sine Wave
Inverter/Charger Operation Guide.
7. Do not expose the Inverter/Charger to rain, snow, or water.
8. To reduce risk of electric shock, disconnect all sources of AC and DC
power from the Inverter/Charger before attempting any maintenance
or cleaning. Turning off controls will not reduce this risk.
9. The Inverter/Charger must be provided with equipment grounding
conductors connected to the AC input ground and chassis ground
terminals.
To reduce the risk of overheating, keep the ventilation openings clear and
do not install the Inverter/Charger in a compartment with limited airflow
or inadequate clearances around the unit. Refer to the RS3000 Sine Wave
Inverter/Charger Installation Guide for required clearance.
CAUTION
Cautions identify conditions or practices that could result in damage to the unit or
other equipment.