Xerox XC811 User manual

XC811/ XC822/ XC830/
XC855/ XC875/
XC1033/ XC1044/ XC1045/
XC1245

©1998 XEROX CORPORATION. XEROX®, The Document Company®,
the stylized X, and the identifying product names and numbers herein are
registered trademarks of XEROX CORPORATION. Xerox Canada Ltd. is
the licensee of all the trademarks. All non-Xerox brands and product
names are trademarks or registered trademarks of their respective
companies.

i
Table of Contents
Getting to Know Your Copier ................................................................ 1
Copier Equipment Listing......................................................................2
Installation.............................................................................................. 3
Power Reduction / Auto Clear ............................................................... 9
Control Panel........................................................................................ 10
Copy Paper Specifications .................................................................. 12
Loading Copy Paper ............................................................................ 13
Flashing .......................................................................................... 14
Making Copies...................................................................................... 16
Making Copies on the Set Document Feeder
(XC855/ XC875/ XC1044/ XC1045/ XC1245).......................................... 17
Copy Quality......................................................................................... 18
Reduction/Enlargement ....................................................................... 20
Copying Oversized Documents........................................................... 21
Bound Original Copying
(XC822/ XC830/ XC855/ XC875/ XC1033/ XC1044/ XC1045/ XC1245).. 21
Paper Tray Bypass (XC811/ XC822/ XC830/ XC855/ XC1033/ XC1044)22
Alternate Paper Tray (XC875/ XC1045/ XC1245).................................. 23
Two-Sided Copying.............................................................................. 25
Customising Your Copier .................................................................... 26
Programmable Features ..................................................................... 26
Programmable Feature Settings 0 – 9 and 12 ..................................... 28
Programmable Feature Setting 10 ...................................................... 29
Copier Care........................................................................................... 30
Cleaning the Document Glass and Cover............................................ 30
Cleaning the Transfer Corotron........................................................... 31

ii
Clearing the Paper Path............................................................. 32
A1 - A2 Set Document Feeder Misfeed................................................ 33
Toner Cartridge Replacement .................................................... 34
Toner Cartridge Yield........................................................................... 35
Drum Cartridge Replacement....................................................... 37
Problem Solving................................................................................... 38
Problem Solving Chart........................................................................ 38
Status Code Chart .............................................................................. 40
Packing the Copier............................................................................... 41
Technical Data...................................................................................... 43

iii
Safety Notes
Your copier and supplies have been designed and tested to meet strict
safety requirements. These include safety agency examination and
approval, and compliance to established environmental standards. Please
read the following instructions carefully before operating your copier and
refer to them as needed to ensure the continued safe operation of your
copier.
• FOLLOW all warnings and instructions marked on or supplied with the
product.
• SYMBOLOGY: = High Voltage, = Heated Surface.
• UNPLUG this copier from the wall outlet before cleaning. Always use
materials specifically designated for this copier. Use of other materials
may result in poor performance and could create a hazardous situation.
• DO NOT use aerosol cleaners. Follow the instructions in this User
Guide for proper cleaning methods.
• NEVER use supplies or cleaning materials for purposes other than
what they were intended. Keep all supplies and materials out of reach
of children.
• DO NOT use this copier near water, wet locations, or outdoors.
• DO NOT place this copier on an unstable cart, stand, or table. The
copier may fall, causing personal injury or serious damage to the
copier.
• YOUR COPIER is equipped with a 3-wire grounding-type plug (i.e., a
plug having a third grounding pin). This plug will only fit into a
grounding-type power outlet. This is a safety feature. To avoid risk of
electric shock, contact your electrician to replace the receptacle if you
are unable to insert the plug into the outlet. Never use a ground
adapter plug to connect the copier to a power source receptacle that
lacks a ground connection terminal.
• YOUR COPIER should be operated from the type of power source
indicated on the marking label. If you are not sure of the type of power
available, consult your local power company.
Required by IEC-950 (EN 60 950) Europe:
The equipment should be installed near an accessible socket outlet
for easy disconnection.

iv
Safety Notes
• YOUR COPIER is equipped with an energy saving device to conserve
power when the machine is not in use. The copier may be left on
continuously.
• DO NOT allow anything to rest on the power cord. Do not locate the
copier where persons will step on the cord.
• IF AN EXTENSION CORD is used with this copier, ensure that the total
of the ampere ratings of the products plugged into the extension cord
does not exceed the extension cord ampere rating. Also, make sure
that the total amperage of all products plugged into the wall outlet does
not exceed the outlet protection.
• SLOTS AND OPENINGS in the cabinet and in the back and bottom of
the copier are provided for ventilation. To ensure reliable operation of
the copier and to protect it from overheating, these openings must not
be blocked or covered. The copier should never be placed near or
over a radiator or heat register. This copier should not be placed in a
built-in installation unless proper ventilation is provided.
• NEVER push objects of any kind into the slots of the copier as they
may touch dangerous voltage points or short out parts that could result
in a risk of fire or electric shock.
• NEVER spill liquid of any kind on the copier.
• NEVER remove any covers or guards that require a tool for removal.
There are no casual operator serviceable areas within these covers.
• NEVER defeat interlock switches. Copiers are designed to not allow
operator access to unsafe areas. Covers, guards, and interlock
switches are provided to ensure that the machine will not operate with
covers opened.
• NEVER put your hands into the fuser area just inside the Exit Tray
area. This area is hot and could produce burns.
• AVOID direct viewing of the document lights. The lamps are bright
and, while not harmful, they may cause an annoying after image. It is
recommended that the Document Cover be kept closed.
• WARNING: In order to allow this equipment to operate in proximity to
Industrial, Scientific and Medical (ISM) equipment, the external
radiation from ISM equipment may have to be limited or special
mitigation measures taken.

v
Safety Notes
• OZONE: A small amount of ozone is produced within the copier during
operation. The amount of ozone emitted by the copier is below the
maximum emission level allowed under the International
Electrotechnical Commission 950 Standard.
This emission level is insufficient to cause any health hazard. However,
when the copier is performing below specification the ozone odor may be
objectionable. It is advisable to place the copier in a room of 1,000 cubic
feet minimum or in a well ventilated room.
This equipment complies with Council Directive 89/336/EEC,
approximation of the laws of the Member States related to
electromagnetic compatibility and Council DIrective 73/23/EEC
ammended by Council Directive 93/68/EEC, approximation of the laws of
the Member States related to low voltage equipment.

vi

1
Getting to Know Your Copier
F
user lever
F
user
T
ransfer corotron
cleaner
T
oner cartridge
D
rum cartridge
T
ransfer corotron
E
xit Tray
C
ontrol panel
D
ocument cover
A
lternate
P
aper Tray
P
aper guides
R
elease lever
Paper Tray Bypass
D
ocument
g
lass
P
ower switch
S
DF Original
G
uides
S
DF Exit Tray
S
DF Input Tray
S
erial Number

2
Copier Equipment Listing
Copier
Number
Paper Tray
Capacity
Paper Tray
Bypass
Alternate
Paper Tray
Bound
Original
Copying
Set
Document
Feeder
XC811 250 sheets single sheet — no no
XC822 250 sheets single sheet — yes no
XC830 100 sheets single sheet — yes no
XC855 250 sheets single sheet — yes yes
XC875 250 sheets — 50 sheets yes yes
XC1033 250 sheets single sheet — yes no
XC1044 250 sheets single sheet — yes yes
XC1045 250 sheets — 50 sheets yes yes
XC1245 250 sheets — 50 sheets yes yes