12) 【set smart zone】：
12.1)【zone number】：【ENT + “ ”to clear old record+ XX + ENT】→“XX”： 2 digitals,
from 02~38
12.2)、【 active digital door sensor】：【 ENT +“▲▼” + ENT】factory default is NO
12.3)、【Door status】：【 ENT +“▲▼” + ENT】
12.4)、【 Active door chime】：【 ENT +“▲▼” + ENT】→factory default is NO
13)【program sensor】： pls check details from accessories part.
14) 【wireless code】：【ENT + “ ”to clear old record + XXXXX + ENT】→“XXXXX”： 5 digits，00000~99999
15)【check alarm record】：【ENT +“▲▼”+ ENT】
16)【checking working record】：
How to Revise Master code?
This setting is for changing the “Enter Code”of the host. The defaulted “Enter Code”is “888888”. If you desire to change, you
may do as below:
In standby mode, press “SET”, the screen will show ”Enter Code”, you can input “999999”(Fixed code), press ENT, the screen will
show “Enter New Code”, please input 6 new digits from keypad, then press “ENT”. Screen will show “Re-enter Code”, pls input
this new digits again, and press “ENT” to confirm. Meanwhile the host panel will be back to the standby mode.
Note: If input the codes 3 times by mistake, the host will be back to the standby mode automatically.
How to operate the Alarm Host?
Record：Slide the switch on the host panel side to “ON”，keep pressing“ ” and speak close to the speaker of host,
and then release, the voice recorded.
Play：Slide the switch on the host panel side to“DC，keep pressing“ ” and you will hear the previous record.
Arm：BY wireless remote：press the corresponding arm button and the host will beep once to successfully complete the
operation
By Host panel(Keypad):【0 + master code + ENT + “▲▼” + ENT】→ “▲▼”to choose “armed home” or “armed away”
Disarm: By wireless remote: press the corresponding disarm button and the host will beep twice to successfully
complete the operation
By Host panel(Keypad): 【ESC + master code + ENT 】→the host will beep twice to successfully complete the
operation
Emergency: By wireless remote: Press Emergency key and the host will alarm immediately;
By host panel(Keypad): press ，and the host will alarm immediately.
Telephone alarm: After receiving the call, you will hear the recorded voice message immediately, it can be played for
30 seconds repeatedly, then follow the below instruction:
1.3.2 Input “8” to enter into the listening status for 20 seconds automatically, you can hear the alarming event sounds
from phone.
1.3.3 Input”#” to play the recorded voice message for one time automatically
1.3.4 Input “*”, the host will end the call and stop dialing any auto dialer#.
1.3.5Directly hang off the telephone, the host will end the call and automatically dial the next auto dialer#.
Arm remotely by phone: 30 seconds after successfully dial the telephone number of host, enter the password of host
after the beep---enter 1 after beep—the host will automatically hang up after beep to successfully complete the
operation.
Notes: You can set “Armed Away” remotely by phone, but keep notes that you can’t set “Armed Home” by this way.
Disarm remotely by phone: 30 seconds after successfully dial the telephone number of host, enter the password of
host after the beep---enter 0 after beep—the host will automatically hang up after beep to successfully complete the
operation.
Check door status: if you try to arm system with door left open, alarm host panel will sound “di di di di”, and show you
below:
“XX”： zone number
“YYYYY”： sensor name
Note：1、This only valid for digital door sensor
