Xylem IQ SensorNet User manual

IQ SensorNet MIQ/IC2 Module
QUICK START GUIDE
Quick Start Guide
YSI Municipal Water •XA00166
Overview
The MIQ/IC2 current input module provides two 0/4 - 20 mA current
inputs for IQ SensorNet and thus enables to connect external sensors
via their current output. Measured values of the external sensors can
be displayed, recorded and processed like the measured values from
IQ SensorNet.
Examples:
• Connecting flow meters to IQ SensorNet
• Connecting level meters to IQ SensorNet
• Connecting analyzers to IQ SensorNet
• Connecting pressure sensors to IQ SensorNet
Scope of Delivery:
• MIQ/IC2 module
• 4 x cable glands (clamping range 4.5-10 mm) with seals and blind
plugs
• 4 x ISO blind nuts M4 with suitable cheese-head screws and plain
washers
• 2 x countersunk screws M3x6 to close the module lid (+ 2
replacement screws)
• 1 x contact base with fixing screws
Materials Required
To set up the MIQ/IC2 module you will need the following tools:
• Cable stripping knife
• Wire stripper
• Phillips screw driver
• Small screw driver
• Cable
TABLE OF CONTENTS:
1. Setup
2. Wiring
3. Configuration
Figure 1: MIQ IC2 Module

2
Warning
This document is not intended to replace the MIQ/IC2
module operation manual. Please use the operating
manual as a reference during the following functions;
installation, operation, cleaning, maintenance and
troubleshooting.
Step By Step Instructions
1Install all cable glands to the bottom of the MIQ/IC2 module as shown below
2Connect the cable to the terminal strip
1. Open the MIQ/IC2 module.
2. Open the cable gland fitting under the required input. Keep the blind plug fitting for later. modifications,
if necessary.
3. Loosen the coupling ring.
4. Feed the cable through the cable gland in the module housing.
5. Open the terminal strip with a small screw driver.
6. Connect the cable to the terminal strip with a small screw driver. Make sure to connect the first device to
“REC 1”.
7. Tighten the coupling ring to secure the cable in place.
8. Close the module.

3
Direct connection with powering the device: The - wire of the current outputs of external measuring sys-
tems need be directly connected to the current inputs (X10) of the MIQ/IC2 module. The + wire of the current
outputs of external measuring systems need be directly connected to the + 24V power supply (X8) of the MIQ/
IC2 module. A jumper cable needs to be ran from the - current inputs (X9) to the - 24V power supply (X7) of the
MIQ/IC2 to complete the loop.
Connect the cable to the device or an isolator.
3
Direct connection without powering the device: The current outputs of external measuring systems can be
directly connected to the current inputs of the MIQ/IC2 module. If the connection data of the external meter is
suitable.
Apply power to device.
Keep in mind the following information when
setting up the MIQ/IC2 Module and third party
devices.
IQSN Power Consumption: The power
consumption is 0.2 watts plus 2.2 watts per
connected power supply/isolator.
Loop Powered Devices: The 24V power supply
in the MIQ/IC2 is rated for 240mA. If powering
two devices make sure the current draw of
the entire 24V loop (the devices and isolators)
doesn’t exceed 240mA.
4
Figure 1: Press the “S” button on the IQ SensorNet controller

4
Scroll down to the “Setting of sensors and
diff. sensors” option and press “OK”.
Select the “Measuring range” column and
press “OK”.
7 Press “Continue” Customize the following settings to the
appropriate values
8
5 6

5
Measuring range Decimal places
11 Display value (0/4mA) Display value (20 mA) 12
9 10

6
Display unit Measured parameter
15 Error detection Error threshold 16
13 14

YSI.com/IQSN
YSI, a Xylem brand
1725 Brannum Lane
Yellow Springs, OH 45387
+1.937.767.7241
[email protected]
YSI.com/IQSN
© 2021 Xylem, Inc. XA00166 0621
QUICK START GUIDE XA00166
MIQ/IC2 REC 2
If only one device is connected to MIQ/IC2
module = Inactive
If two devices are connected to MIQ/IC2 module
= Active
Press “Save and quit”
1817