Yaesu FTM-10R User manual

Memory Set Mode
Press and hold the key for one second to enter the Memory Channel Set Mode.
Clock/Timer Set Mode
Press and hold the [VOL/SEL]key for one second to enter to the Clock/Timer Set Mode while the clock/timer
function is activated.
Smart Menu Key
Top panel /keys, and the key select and enable operation of the following features.
Display
T 1 TIME ADJ
T 2 CLOCK BP
T 3 T FORMAT
T 4 12H/24H
T 5 TMR BEEP
T 6 APO
Function
Set up the Clock.
Set an alarm beep which will sound every “00” minutes.
Change the Clock Format.
Change the Time System.
Stop Watch Timer allows programming a timed interval when a beep will sound and
the white LED will flash.
Selects the Automatic Power Off time (time before power goes off).
Page
53
84
83
84
84
85
Page
25
26
27
27
27
27
27
28
28
29
29
30
31
30
32
32
32
Function
Press the key to activate the AF Dual function.
Press the key to activate the ARTS feature.
Press the key to enable adjustment of the display illumination level by the DIAL knob.
Press the PTT switch to activate the sound of a Gong Bell.
Press the PTT switch to activate the sound of a UFO in flight.
Press the PTT switch to activate the sound of a klaxon.
Press the PTT switch to activate the sound of a siren.
Press the key to activate the Intercom mode.
Press the key to disable noise and tone squelch.
Press the PTT switch to route your amplified voice through the PA speaker.
Press the key to activate the Reverse feature.
Press the key to activate the scanner.
Press the key to activate the Smart Search.
Press the key to enable adjustment of the noise squelch threshold level by the DIAL knob.
Press the key to activate the 1750 Hz Tone Burst.
Press the key to change the transmit power level.
Press the key to change the receiver audio level of the intercom receiver.
Display
AF DUAL
ARTS
DIMMER
HORN 1
HORN 2
HORN 3
HORN 4
INTERCOM
MONI
PA
REVERSE
SCAN
SQL LEVL
SSCH
TCALL
TX POWER
VOL.ITCOM
When one of the above features does not appear in the list, it is because that feature is not assigned to the top panel
/keys. Please insure the Smart Menu “F14 FKEY MOD” is set to “FNC” or “FNC+MSG”.
Display
M 1 GROUP
M 2 MEM CH
M 3 MEM SORT
M 4 MEM TAG
M 5 SCN TYPE
M 6 SKIPONLY
M 7 SQL LEVL
M 8 SQL TSQF
M 9 SQL DCS
M10 SQL TYPE
M11 TX SHIFT
M12 TX POWER
M13 DELETE
Page
36
37
37
38
39
39
40
40
41
41
42
43
43
Function
Assigns/Eliminates the memory channel to/from the Memory Group Memory bank.
Changes the memory channel number to the desired vacant memory channel number.
Sorts and renumbers the Memory Channels by frequency, from low to high.
Appends an Alphanumeric “Tag” (label) to a memory channel.
Sets the Scan Type (Skip Memory or Preferential Memory).
Set the Preferential Scan List.
Sets the Squelch Threshold Level.
Change the CTCSS Tone Frequency.
Change the DCS Code.
Change the Squelch Type (CTCSS or DCS).
Stores an independent (in band) transmit frequency (Odd Split).
Change the Transmitter Power Level.
Deletes memorized data (except CLUB memory channel).

EH027M401
Menu Mode
Press and hold the [VOL/SEL]key for one second to enter to the Menu Mode while the VFO mode or Memory mode.
Display Function Page
F 1 AF AUTO Enables/Disables the Automatic Audio Volume Controller. 56
F 2 AF DUAL Enables/Disables the AF DUAL operation. 25, 62
F 3 AF PITCH Select the Tone Pitch control for the received audio. 85
F 4 AF PREST Enable/Disable the Volume Setting Alert feature. 86
F 5 AF-VFO Select the DIAL knob and display function. 57
F 6 BEEP Enables/Disables the beeper. 77
F 7 BLU SAVE Enable/Disable the battery saver of the optional BH-1 Bluetooth®Headset. 61
F 8 BLU VOX Enables/Disables the Bluetooth® function (requires the optional BU-1 Bluetooth® Unit). 61
F 9 CLOCK Activates/Disables the Internal Clock/Stop Watch Timer. 53
F10 CLUB PRI Activates the Club Channel Monitor. 44
F11 DC VOLT Indicates the DC Supply Voltage. 83
F12 DIMMER Setting of the display’s illumination level. 94
F13 DTMF Programming of the DTMF Autodialer. 71
F14 FKEY MOD Selects the category which is recalled from the top panel /key. 94
F15 FKEY SEL Assigns a function to the Function Key. 77
F16 ID LIST Programming a Member List for the Message feature. 47
F17 ID REG Sets your Personal ID for the Message feature. 49
F18 MESSAGE Programming a Message for the Message feature. 46
F19 MIC GAIN Adjust the microphone gain level. 87
F20 MIC PRGM Select the function of the microphone’s [PGM]key. 79
F21 PAGER Enables/Disables the Enhanced CTCSS Paging & Code Squelch function. 66
F22 PTT LOCK Enables/Disables the locking of the PTT key when the LOCK mode is activated. 87
F23 PTT MODE Selects the PTT key function. 77
F24 RPT ARS Enables/Disables the Automatic Repeater Shift function. 74
F25 RPT MODE Sets the Repeater Shift Direction. 73
F26 RPT SFT Sets the magnitude of the repeater Shift. 73
F27 RX EXP Enables/Disables the band expansion. 74
F28 RX F CCL Shifting of the CPU clock frequency. 96
F29 RX M MOD Selects the receiving mode. 76
F30 SCN CVRG Selects the Scan range. 80
F31 SCN DRCT Select the Scan type. 81
F32 SCN MODE Selects the Scan Resume mode. 80
F33 SCN STRT Select the scan start direction which initiates the scanner using the scan command. 81
F34 SPEAKER Select the Speaker to be used. 86
F35 SQL BELL Selects the number of CTCSS/DCS/EPCS Bell ringer repetitions. 82
F36 SQL DCS Setting of the DCS code. 65
F37 SQL EXP Enables/Disables split CTCSS/DCS coding. 82
F38 SQL LEVL Set the squelch threshold level. 98
F39 SQL TSQF Setting of the CTCSS Tone Frequency. 64
F40 SQL TYPE Selects the Tone Encoder and/or Decoder mode. 64, 65
F41 STEP Setting of the synthesizer steps. 76
F42 STEREO Select the audio output. 87
F43 TOT Setting of the TOT time. 58
F44 TX POWER Selects the transmit power output level. 99
F45 VOL.ITCOM Sets the volume level of the intercom mode. 100
F46 VOX MIC Enables/Disables VOX operation. 57
F47 VOX SENS Sets the VOX sensitivity. 58
F48 WIRES Enable/Disable the Internet Connection feature. 68
F49 WX ALERT Enables/Disables the Weather Alert Scan feature. 100