Yakima K117 User manual

K117
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 2 x 2 x 4
Revision No: 4D 1

Fitting Kit K117
MAX kgs (lbs)
W/P WHD
Toyota
Camry 20 Series, 5dr Wagon May 98-Aug 02 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Camry, 5dr Estate 97-01 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Camry, 5dr Wagon Sep 97-Sep 02 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Vienta, 5dr Wagon Aug 97-Oct 00 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K117
X
A B C 1 2 3
Camry 20 Series, 5dr Wagon May 98-Aug 02 (AU) -300mm 300mm - 844mm 835mm -
-11 -13/16ths" 11 13/16ths" - 33 1/4ths" 32 7/8ths" -
Camry, 5dr Estate 97-01 (EU) -300mm 300mm - 844mm 835mm -
-11 -13/16ths" 11 13/16ths" - 33 1/4ths" 32 7/8ths" -
Camry, 5dr Wagon Sep 97-Sep 02 (NZ) -300mm 300mm - 844mm 835mm -
-11 -13/16ths" 11 13/16ths" - 33 1/4ths" 32 7/8ths" -
Vienta, 5dr Wagon Aug 97-Oct 00 (AU) -300mm 300mm - 844mm 835mm -
-11 -13/16ths" 11 13/16ths" - 33 1/4ths" 32 7/8ths" -
3

Fitting Kit EN
K117
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K117
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K117
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 262B
B = 312B
6

Fitting Kit EN
K117
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pads (supplied with fitting kit) to
foot.
7

Fitting Kit EN
K117
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Clamps over rubber door frame mouldings.
●Press adjusting screw to adjust the leg
positions on the crossbar.
8

Fitting Kit EN
K117
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
9

Fitting Kit EN
K117
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10