Yakima Landing Pad 15 User manual

LANDING PAD #15
1035589A-1/9
Refer to YAKIMA Control Tower instructions for important
warning and load limitations, and YAKIMA’s limited warranty.
CATCH MOUNT (DRIVER REAR)
(WITH SCREW)
CATCH MOUNT(PASSENGER FRONT)
(WITH SCREW)
BARE MOUNT (PASSENGER REAR)
BARE MOUNT (DRIVER FRONT)
COVER (4X)
(USE SUPPLIED M8 FASTENER
AND WASHER)
(USE SUPPLIED M6 FASTENER
AND WASHER)
INCLUDED TOOLS:
HEX WRENCH (1X)
SIX LOBE WRENCH (1X)
FASTENER (M6) FASTENER (M8)
WASHER (M6) WASHER (M8)

1035589A-2/9
Remove factory crossbars.
• Driver Side Rear & Passenger Side Front: Lift tab to release
crossbar. Reference your owner’s manual for more information.
• Passenger Side Rear & Driver Side Front: Use six lobe wrench
to remove factory installed fasteners.
• Store fasteners and factory crossbars in a safe place.
• Using the hex wrench fully open both Catch
Mounts by turning the screw counter-clockwise.
DO NOT DRIVE VEHICLE WITHOUT EITHER FACTORY
CROSSBARS OR YAKIMA LANDING PADS INSTALLED.
Prepare Catch Mount.

1035589A-3/9
2X
2X
Install Landing Pads.
Continue with Control Tower installation.
• Using the hex wrench install each Catch Mount and pad as pictured (Catch Mounts are located diagonally from one another). Fully tighten.
• Using the hex wrench install the fastener, washer, Bare Mount, and pad as pictured (Bare Mounts are located diagonally from one another).
To prevent screws from cross-threading start threading fastener using your fingers. Fully tighten.
• Use covers whenever Control Towers are not installed.
• Store covers in safe place whenever Control Towers are installed.
• Periodically remove landing pad and clean under pad.
• Periodically inspect pad for wear or cracking. Replace if damaged.
ATTACHMENT
HARDWARE CAN
LOOSEN OVER TIME.
CHECK AND TIGHTEN
AS NECESSARY,
BEFORE EACH USE.
RECOMMEND
INSTALLATION
TORQUE: 20 IN-LBS
(2.3Nm)
RECOMMEND
INSTALLATION
TORQUE: 20 IN-LBS
(2.3Nm)
CATCH MOUNT
BARE MOUNT
FASTENER (M6)
FASTENER (M8)

LANDING PAD #15
1035589A-4/9
On trouvera dans les instructions accompagnant les pieds Control Tower de YAKIMA les
avertissements importants et les limites de charge, en plus de la garantie limitée YAKIMA.
CACHE (x 4)
OUTILS INCLUS :
CLÉ HEXAGONALE (X 1)
CLÉ À SIX LOBES (X 1)
VIS (M6) VIS (M8)
RONDELLE (M6) RONDELLE (M8)
PATIN À BAÏONNETTE – CÔTÉ
CONDUCTEUR ARRIÈRE (AVEC VIS)
PATIN À BAÏONNETTE – CÔTÉ
PASSAGER AVANT (AVEC VIS)
PATIN SANS BAÏONNETTE
– CÔTÉ PASSAGER ARRIÈRE
(EMPLOYER LE BOULON M8 ET
LA RONDELLE FOURNIS)
PATIN SANS BAÏONNETTE
– CÔTÉ CONDUCTEUR
AVANT (EMPLOYER
LE BOULON M6 ET LA
RONDELLE FOURNIS)

1035589A-5/9
Enlever les barres transversales d’origine. • Côté conducteur arrière et côté passager avant : soulever le levier
pour libérer les barres transversales. Consulter le manuel du véhicule
pour plus de détails.
• Côté passager arrière et côté conducteur avant : employer la clé à
six lobes pour enlever les boulons installés à l’usine.
• Conserver soigneusement les vis et les barres transversales d’origine.
• À l’aide de la clé hexagonale, “ouvrir” les patins
à baïonnette en tournant la vis vers la gauche.
NE PAS CONDUIRE LE VÉHICULE SANS QUE NE
SOIENT EN PLACE SOIT LES BARRES TRANSVERSALES
D’ORIGINE, SOIT LES PATINS LANDING PAD YAKIMA.
Préparer les patins à baïonnettes.