Yetter TITAN Series User manual

TITANSERIES
2967-013B /2967-014B
NARROW ROW SHORT U.N.T. ™
RESIDUE MANAGER
OPERATOR’S MANUAL
PART IDENTIFICATION
2565-748_REV_J 07/2021
YETTER MANUFACTURING CO.
FOUNDED 1930
Colchester, IL 62326-0358
Toll free: 800/447-5777
309/776-3222 (Fax)
Website: www.yetterco.com
E-mail: [email protected]

2
FOREWORD
You’ve just joined an exclusive but rapidly
growing club. For our part, we want to
welcome you to the group and thank you for
buying a Yetter product.
We hope your new Yetter products will help
you achieve two goals: increase your
productivity and increase your efficiency so
that you may generate more profit.
This SAFETY ALERT SYMBOL
indicates important safety
messages in the manual. When
you see this symbol, be alert to
the possibility of PERSONAL INJURY and
carefully read the message that follows.
The word NOTE is used to convey
information that is out of context with the
manual text. It contains special information
such as specifications, techniques, and
reference information of a supplementary
nature.
The word IMPORTANT is used in the text
when immediate danger will occur to the
machine due to improper technique or
operation.
It is the responsibility of the user to read the
owner’s manual, comply with safe and
correct operating procedure, and to
lubricate and maintain the product
according to the information listed in this
owner’s manual.
The user is responsible for inspecting their
machine and for having parts repaired or
replaced when it is damaged or worn.
Continued use of a damaged or worn part
can cause injury or more extensive damage
to the machine.
If you have any questions regarding the
information given in this manual, consult
your local Yetter dealer or contact:
Yetter Manufacturing Co.
[phone]
[phone]
Website: www.yetterco.com
Email: in[email protected]m
WARRANTY
Yetter Manufacturing warrants all products manufactured and sold by it against defects in material. This
warry being expressly limited to replacement at the factory of such parts or products that appear to be
defective after inspection. The warranty does not obligate Yetter Manufacturing to bear the cost of labor
in replacement of parts. It is the policy of the Company to make improvements without incurring
obligations to add them to any unit sold prior. No warranty is made, or authorized to be made, other than
herein set forth. This warranty is in effect for one year after purchase.
Dealer:__________________________
Yetter Manufacturing warrants its own products and cannot be held responsible for damages to
equipment on which they are mounted.

3
TABLE OF CONTENTS
SAFETY INFORMATION ...........................................................................4
BOLT TORQUE..........................................................................................3
INSTALLATION INSTRUCTIONS...........................................................5-6
OPERATION ...........................................................................................7-9
PART IDENTIFICATION .....................................................................10-15
BOLT TORQUE
Important: Over tightening hardware can cause as much damage as under tightening.
Tightening hardware beyond the recommended range can reduce it shock load
capacity.
All hardware used on the TitanTM Residue Manager is Grade 5 unless otherwise
specified. If hardware must be replaced, be sure to replace it with hardware of equal
size, strength, and thread type.
The chart below is a guide for proper torque. Use it unless a specified torque
value is given elsewhere in the manual.
Torque is the force you apply to the wrench handle times the length of the handle.
Use a torque wrench wherever possible
The following table shows torque in ft-lbs for coarse thread hardware.

4
SAFETY INFORMATION
BE ALERT!
YOUR SAFETY IS INVOLVED
It is the responsibility of the owner, operator, or supervisor to know and instruct
everyone using this machine at the time of initial assignment and at least annually
thereafter, of the proper operation, precautions, and work hazard which exist in the
operation of the machine in accordance with OSHA regulations.
SAFETY IS NO ACCIDENT
The following safety instructions combines with common sense will save your
equipment from needless damage and the operator from unnecessary exposure
to personal hazard. Pay special attention to the caution notes in the text. Review
this manual each year and with new and experience operators.
1. Read and understand the operator’s manual before operating this machine.
Failure to do so is considered a misuse of the equipment.
2. Make sure equipment is secure before use.
3. Always keep children away from equipment while in operation.
4. Make sure everyone that is not directly involved with the operation is clear of the
work area before use.
5. Be sure all safety devices, shield, and guards are in place and functional before
beginning operation
6. Shut off all power to the unit prior to adjustment, servicing, or cleaning.
7. Keep hands, feet, and clothing away from moving parts. It is a good idea to
remove all jewelry before starting the operation.
8. Visually inspect the machine periodically during operation for signs of excessive
vibration, loose fasteners, and unusual noises.
WARNING: Never work around the toolbar/implement while in a raised position
without using safety lockups.
CAUTION: The TitanTM Residue Manager attachments are very heavy. Pay extra
attention to lifting techniques while handling and/or maneuvering the opener
during assembly. Failure to do so may lead to personal injury.

5
INSTALLATION INSTRUCTIONS
2967-013A
STEP 1. Attach the Residue Manager Assembly to the planter unit using 3) ½” bolts
and lock nuts.
2967-014A
STEP 1A.Attach the 2966-293 adapter to the CIH row unit using the 1/2” x 3-1/2” bolts
and lock nuts then install the Residue Manager Assembly to the adapter using the 1/2” x
1-1/2” carriage bolts and flanged lock nuts.
INSERT 1/2” X 1” BOLT THROUGH
THE LOWER RIGHT HOLE IN ROW
UNIT FROM REAR AND THREAD
INTO THE MOUNT BRACKET
INSERT 1/2” X 1” BOLT
THROUGH THE LOWER LEFT
HOLE IN ROW UNIT FROM THE
REAR AND THREAD INTO THE
MOUNT BRACKET

6
INSTALLATION INSTRUCTIONS
STEP 2. Choose the hole in which to attach the R.M. wheel assemblies. Attach the R.M.
wheel/hub assemblies to the combo arm using 5/8” lock washers and hex nuts. Torque to 150
ft. lbs.
Step 3: ONLY FOR 2967-014B MOUNTING ON CNH RU
Attach the up-stop to the planter row unit parallel arms using the provided
hardware.
UP-STOP

7
OPERATION
CAUTION: Where rocks are present the residue manager should be set in the “float”
position, not locked down.
Adjust the residue manager to move crop residue aside and not move any soil. Adjustments to the residue manager
may have to be made when changing field conditions and type and amount of residue. Use the handle for leverage
when changing depth settings.
“FLOAT SETTINGS”
Install the adjustment pin below the combo arm.
To raise the wheels, lift the 2966-201 and move the adjustment pin up.
To lower the wheels, move the adjustment pin down.
“RIGID SETTING”
Install the adjustment pin through the combo arm.
To raise the wheels, lift the 2966-201 combo arm to the desired position and insert the pin.
To lower the wheels, lower the combo arm to the desired position and insert the pin.
ROW CLEANER DO’S AND DON’TS
1. DO NOT move soil; Residue Managers are designed to move crop residue only.
2. DO NOT operate planter at slow speeds, ground speed affects how aggressive the spoke
wheels are; operate at sufficient speed (4-6 mph) to maintain good residue flow.
3. DO NOT expect 100% of crop residue to be cleared, it is not necessary and would
necessitate engaging the soil. The width of path cleared depends on ground conditions,
depth setting and ground speed.
4. DO expect to see wheels occasionally quit turning, indicates ideal (shallow) setting which
is not moving soil.
5. DO adjust toolbar frame height 20”-22” and drawbar to “level” correctly. Very important to
ensure planter opener will follow ground contours properly.

8
OPERATION PRECAUTIONS
STOP
Read this before using the Yetter product.
-MACHINE OPERATION
IMPORTANT: failure to properly set the planter frame height and
levelness can result in less than successful operation of the planter
and the Yetter product and may result in damaged equipment. All
operators should read and thoroughly understand the instructions
given prior to using the Yetter product.
NOTE: DO NOT use this product if the planter is not adjusted properly!
Leveling the planter:
With the planter lowered to proper operating height (Usually 20”-22”).
Read the planter operator’s manual for recommended setting. Check
to be sure the toolbar and row unit parallel arms are level fore and aft. Re-
check when the planter is in the field and has been fully loaded with
seed, fertilizer, granular chemicals, etc. Also, a field check with a bubble
level on the frame should be made of the hitch height to ensure level
operation front to back.
It is important for the planter to operate level laterally. Tire pressure must
be maintained at pressures specified by the manufacturer.
Field and actual planting conditions change and will dictate planter frame
heights. You must ensure that the row unit parallel arms are
approximately parallel with the ground.
IMPORTANT: For proper operation of the planter attachments and row
units, it is imperative that the planter toolbars and row unit parallel arms be
level side-to-side and front-to-rear. The toolbar frame should operate at a
20”-22” height from the planting surface. Check the manufacturer’s
operator’s manual for instructions on how to adjust the frame height and
levelness.

9
PLANTER ADJUSTMENT

10
PART IDENTIFICATION
2967-013B

11
PART IDENTIFICATION
2967-013A-SUB ASSEMBLY

12
PART IDENTIFICATION
2967-014B

13
PARTS IDENTIFICATION
2965-135 UP-STOP KIT
ITEM
PART #
DESCRIPTION
QTY
1
2502-244
3/8-16 x 1-1/4 HHCS GR 5
2
2
2960-223
UP-STOP
2
3
2520-255
3/8-16 HEX LOCK NUT
2
4
2526-253
3/8 SAE FLATWASHER
2

14
PARTS IDENTIFICATION
2966-140-ST-FW
RIGHT HAND SHARK TOOTH WHEEL ASSEMBLY
PARTS IDENTIFICATION
2966-140-BW-FW
RIGHT HAND BEVEL WHEEL ASSEMBLY

15
PARTS IDENTIFICATION
2966-141-FW
LEFT HAND SPOKE WHEEL ASSEMBLY

16
2565-748_REV_J ● 07/2021