YOKOGAWA Field Mate 3 Instruction Manual

Volumetric Displacement
ontrolC System
Fertilizer
Users Guide
and
Installation Manual
1

Ver 1.0
FIELD MATEtm USER MANUAL
Copyright
All information contained in this user's guide is the
property of G-Tech NZ td. All rights reserved. This
user's guide may not be , in whole or in part, be copied,
photocopied, reproduced, stored, or reduced to any
electronic medium or machine readable form, without
permisssion from G-Tech NZ td.
If you Need to Call Customer Service
Please complete the following information for future
reference:
Field Mate Model* :............................................................
Serial Number * :................................................................
Date Purchased :.................................................................
Place of Purchase:...............................................................
* The Serial/Model Number is displayed in the
Information Screens of the meter.
2

Warranty :
EMI Emmisssion Certification:
1 Year return to factory Warranty on Electric Drive components, sensors and Downloading support hardware.
Please ensure you agree to the warrantry conditions before proceeding to purchase this product, read the warranty form
at the end of this user guide. Installation wiring to sensors and wear and tear on connectors not covered
NOTE:
The
We question. smallest the even have you if 'Anytime'upport s dealer your Call help. to here are
system. the by released being is amounts correct the ensure to
system metering the on bag a ithw runs test drill needed if and system the understand should operator
issue. out with operating is it ensure to system the monitor
to and correctly up system drive Electric the set dealer toor operator the of responsibilty sole the is t I
product. this using from result
that irregularities planting mishaps, any for responsible or liable way no in is Limited Zealand New Gtech
.
Electro magnetic interference emmission certification are a series of tests that required to be passed beforean
electronic device can be sold. These test are related to how much electron magnetic radiation is emmitted by
an electronic device.
The Area meter has the following certifications and is suitable for sale in the following countries:
Certification Countries
C-Tick Z874 Class B New Zealand, Australia
Europe
CE
3

Specifications:
Features:
SPECIFICATI NS
Supply volts : 5 – 15 Volts
Monitor Current : 75ma
Temperature : -5 to 55 degree/C
Input voltages : 0 to 30 Volts
Max Width : 99.99 Meters
Distance : 999.99 km
Max Speed : 20 km/Hr
Wheel Size : 999.9 cm
Max Motor Amps : 20 amps per motor
- Up to 4 metering unit motors
- Fan speed monitoring
- Hardware fault monitors on all motor channels
- Real time motor RPM displayed to give real world
proformance measurment ott he users.
- Fast drill calibration
- Instant feed back on system operation when setting the
drilling rate
- Can be set up to work in KG/Hect mode or precision
seeder control mode.
- Prestart mode available for air seeder
- ow bin feature available
- Auto greaser control available
- All information retained on monitor.
- Report feature available
- All inputs high voltage protected.
4

Wiring Connections:
12 Pin Connector
1- Ground Black Ground signal to all sensors
6-
Speed
Yellow Speed pulse (Switch to GND to trigger)
5- Hold
GPS nc
Speed
Sy
White Hold signal (Switch to GND to trigger)
3-
PumpPaint
Distance Green GPS Sync Pulse
(Switch to GND to trigger)
2- Brown
7- Red
4- Blue
Pump Supply
Solenoid
solenoid
Gnd
P wero
power
Power
8- rive
D
Brown Green Pai t
Paint
Displacement
n
9- Drive Paint Solenoid
White Blue
10- Drive Displace Solenoid Black Yellow
11-
Power
Brown Red
12- Ground Black rSotoMolenoid/Pump
8

ain Screen M
9
Last distance travelled from sync pulse
Sync pulse spacing
Current distance
travelled from sync
pulse
State machine status.
Relects fert release
function control
Ground speed
system voltage
plant counter
The fert distance counts
down here.
paint pump status
paint solenoid
time in milli
seconds

Job Screen details
(Enter the J B screens by Quick pressing the P WER key)
Inside the J B menu...
Change the job
Hold ARROW key to select
Bin1 libary select .
Currently set to 1
Bin2 libary select .
Currently set to 1
Move to new job if
required
Current JOB. To reset
or view details hold any
ARROW key.
Start Job1
RESET Job1
View Job1 Report
13

ption Screen details
(Enter the PERATE screens by Quick pressing the P WER key)
Inside the PERATE menu...
(Move through the PERATE screens using the ARR W keys - Quick Press!)
Quick Press the
POWER key to enter
the OPERATE mode.
Area Drill for the
current job
SUB AREA drilled for
this job. This total can
be cleared by holding
down any ARROW key.
If reset no other totals
are effected.
Speed of the drill in KM/HR.
NOTE!! get this number right so the true
speed of teh drill is seen here!!
If the monitor is not displaying the true
ground speed then the drilling rates
will not be as expected.
IT IS THE SO E RESPONSIBI TY OF THE USER
TO GET THIS RIGHT.!
FIE DMATE SUPPORT IS HERE TO HE P,
CONTACT US ANYTIME FOR SETUP SUPPORT.
14

Inside the PERATE menu. More..
Working RATE of the
Drill. Displayed in
Hectare/Hour.
15

Setup Screen details
(Enter the SETUP screens by Quick pressing the P WER key)
Inside the SETUP menu...
(Move through the SETUP screens using the ARR W keys - Quick Press!)
- Set the CD Contrast
- Set the Debounce for the
Speed sensor.
- HO D Mode. Extern OW for
ift switch. Use STITCH O
when using the rate Reducer.
- The distance travelled for ever
Speed sensor pulse.
- Working width of the drill.
Quick Press the
POWER key to enter
the SETUP mode.
NOTE: When exiting SETUP turn the
monitor OFF then ON. If not done
"CYC E POWER" will flash and the
motors will not run.
- Set Date used by REPORTS
- Support Phone number.
- Unit ID for REPORTS
- Set Time used by REPORTS
- PWM PO ING is the power
update rate for Motors. Setting
'04' is recommended
17
Fert release distance from
SYNC pulse
Paint solenoid on time. Activates
when SYNC pulse occurs
Distance travell between each
SYNC pulse

REPORT Screen details
(Enter the REP RT screens by Quick pressing the P WER key)
Inside the REP RT menu...
(Move through the REP RT screens using the ARR W keys - Quick Press!)
Quick Press the
POWER key to enter
the REPORT mode.
- Name of BIN1
- Name of BIN2
- Name of BIN3
- Name of BIN4
- Name of this monitor
- Area Drilled in Hectares
- Distance drilled
- Distance travelled in HO D
mode (Not Drilling)
20

Inside the REP RT menu. More..
- Time with the drill in RUN
mode and Drilling.
- Time with the drill in RUN
mode and stationary.
- Time with the drill in HO D
Mode, with the drill moving.
- Time with the drill in HO D
Mode, the drill is stopped.
21

Inside the REP RT menu. More..
- Date that the current Drilling
Job was started
- Time the current Drilling job
was started.
- Size of the DISTANCE
PU SE number used to calc
the area for this job.
- Size of the DRI WIDTH
number used to calc the area
for this job.
- Number of Speed pulses
counted while drilling.
- Number of speed pulses
counted while not drilling, in
HO D mode.
- Total time spent drilling. This
time includes all times, moving
and stopped.
22

INF Screen
(Enter the INF screen by quick pressing the P WER key)
Inside the INF menu...
(Move through the INF screens using the ARR W keys - Quick Press!)
Quick Press the
POWER key to enter
the INFO screen.
LOGO
24
HELP
Direct
International
use
0064211535759
callers
Zealand. New in with dial
number. DESKphone
Back
drill. of speed ground
calculation to number ground

25
Inside more menu... INFO the
-
-
-Time
- Time
- Life
- Backlight status and volatge
drilled hectare time
drilling been has moniotr
up powered been has monitor
version Firmware
Model Monitor
-
-
-
-
-
-
applied
rate drilling of % rate drill educedR
status sensor
bin owL
number
Serial
monitor into voltage Battery
units easurementM
temperature Monitor
-
These
-
counter. on/off Power
metrics.
proformance
system or detection error
these to vectors software thetime
every increment will counter
system. detection error ware oftS
Back
measurement
distance and timer back for
numbers calculation ground

26
Inside more menu... OINF the
- Real
- Run
support Time
support calculation Area
-
-
Status Hold
status Clock Time
- Buzzer
-
- numbers support Area Total
calculation
AREA the for numbers ground Back
status
- Rate Reduction feature status
Table of contents
Other YOKOGAWA Control System manuals
Popular Control System manuals by other brands

Balboa
Balboa 300F manual

Tigo
Tigo TS4-R Installation & quick start guide

Mitsubishi Electric
Mitsubishi Electric MELDAS 60 Series Programming manual

Whelen Engineering Company
Whelen Engineering Company PCCS9R installation guide

MLC
MLC LC100 user manual

CSP Products
CSP Products SENTRY BARRIER TL-4 Product and installation manual