YOKOGAWA UV700G User manual

User’s
Manual UV700G
UV Analyzer
(ORGANIC POLLUTANT MONITOR)
IM 12K01B02-01E
IM 12K01B02-01E
6th Edition

i
IM 12K01B02-01E
<INTRODUCTION>
INTRODUCTION
This manual describes the operation of the UV700G.
Be sure to read this manual before using the product to ensure proper and safe operation of the
instrument. Also safely store the manual so it is readily available whenever necessary.
Product specications and appearance, as well as the contents of this manual are subject to
change without notice.
nWarranty and Responsibility
Yokogawa warrants that the Product shall be free from defects in material and workmanship and
agrees to repair or replace free of charge, at Yokogawa’s option, any malfunctioned or damaged
Product attributable to Yokogawa’s responsibility for a period of one (1) year from the delivery
unless otherwise agreed with a written agreement. In any one of the following cases, none of the
warranties set forth herein shall be extended;
• Any malfunction or damage attributable to improper operation
• Any malfunction attributable to repair or modication by any person not authorized by
Yokogawa
• Any malfunction or damage attributable to the use in an environment not specied in this
manual
• Any malfunction or damage attributable to violation of the instructions in this manual or
operations in the manner not specied in this manual
• Any malfunction or damage attributable to any cause or causes beyond the reasonable
control of Yokogawa such as natural disasters
• Any deterioration in appearance attributable to corrosion, rust, and so on
• Replacement of consumables
YOKOGAWA SHALL NOT BE LIABLE FOR ANY DAMAGES RESULTING FROM ANY MAL-
FUNCTIONS OF THE PRODUCT, ANY ERASURE OF DATA, OR ANY OTHER USES OF THE
PRODUCT.
nNotes on Handling User’s Manuals
• Please hand over the user’s manuals to your end users so that they can keep the user’s
manuals on hand for convenient reference.
• Please read the information thoroughly before using the product.
• The purpose of these user’s manuals is not to warrant that the product is well suited to any
particular purpose but rather to describe the functional details of the product.
• No part of the user’s manuals may be transferred or reproduced without prior written con-
sent from YOKOGAWA.
• YOKOGAWA reserves the right to make improvements in the user’s manuals and product at
any time, without notice or obligation.
• If you have any questions, or you nd mistakes or omissions in the user’s manuals, please
contact our sales representative or your local distributor.
Media No. IM 12K01B02-01E 6th Edition : Feb. 2021 (YK)
All Rights Reserved Copyright © 2007, Yokogawa Electric Corporation

ii
IM 12K01B02-01E
<INTRODUCTION>
Safety Precautions
n Safety,Protection,andModicationoftheProduct
• In order to protect the system controlled by the product and the product itself and ensure
safe operation, observe the safety precautions described in this user’s manual. We assume
no liability for safety if users fail to observe these instructions when operating the product.
• If this instrument is used in a manner not specied in this user’s manual, the protection
provided by this instrument may be impaired.
• If any protection or safety circuit is required for the system controlled by the product or for
the product itself, prepare it separately.
• Be sure to use the spare parts approved by Yokogawa Electric Corporation (hereafter
simply referred to as YOKOGAWA) when replacing parts or consumables.
• Modication of the product is strictly prohibited.
• The following safety symbols are used on the product as well as in this manual.
CAUTION
This symbol gives information essential for understanding the operations and functions.
NOTE
This symbol indicates information that complements the present topic.
nWarning and Disclaimer
The product is provided on an “as is” basis. YOKOGAWA shall have neither liability nor respon-
sibility to any person or entity with respect to any direct or indirect loss or damage arising from
using the product or any defect of the product that YOKOGAWA can not predict in advance.

iii
IM 12K01B02-01E
<INTRODUCTION>
After-sales Warranty
nDo not modify the product.
n During the warranty period, for repair under warranty consult the local sales representative
or service o󰀩ce. Yokogawa will replace or repair any damaged parts. Before consulting for
repair under warranty, provide us with the model name and serial number and a description
of the problem. Any diagrams or data explaining the problem would also be appreciated.
• If we replace the product with a new one, we won’t provide you with a repair report.
• Yokogawa warrants the product for the period stated in the pre-purchase quotation Yokoga-
wa shall conduct dened warranty service based on its standard. When the customer site is
located outside of the service area, a fee for dispatching the maintenance engineer will be
charged to the customer.
• Returned goods that have been in contact with process uids must be decontaminated and
disinfected prior to shipment. Goods should carry a certicate to this e󰀨ect, for the health
and safety of our employees. Material Safety Data sheets must be included for all compo-
nents of the process to which the sensor have been exposed.
n In the following cases, customer will be charged repair fee regardless of warranty period.
• Failure of components which are out of scope of warranty stated in instruction manual.
• Failure caused by usage of software, hardware or auxiliary equipment, which Yokogawa
Electric did not supply.
• Failure due to improper or insu󰀩cient maintenance by user.
• Failure due to modication, misuse or outside-of-specications operation which Yokogawa
does not authorize.
• Failure due to power supply (voltage, frequency) being outside specications or abnormal.
• Failure caused by any usage out of scope of recommended usage.
• Any damage from re, earthquake, storms and oods, lightning, disturbances, riots, warfare,
radiation and other natural changes.
n Yokogawa does not warrant conformance with the specic application at the user site.
Yokogawa will not bear direct/indirect responsibility for damage due to a specic application.
n Yokogawa Electric will not bear responsibility when the user congures the product into
systems or resells the product.
n Maintenance service and supplying repair parts will be covered for ve years after the pro-
duction ends. For repair for this product, please contact the nearest sales o󰀩ce described in
this instruction manual.

Blank Page

v
IM 12K01B02-01E
<CONTENTS>
UV700G
UV Analyzer
(ORGANIC POLLUTANT MONITOR)
CONTENTS
IM12K01B02-01E6thEdition
INTRODUCTION.............................................................................................i
Safety Precautions .......................................................................................ii
After-sales Warranty ...................................................................................iii
1. Overview.................................................................................................... 1-1
1.1 Introduction ....................................................................................................... 1-1
1.2 Description of Parts.......................................................................................... 1-2
1.2.1 Unit..................................................................................................... 1-2
1.2.2 Display ............................................................................................... 1-4
2. Specication ............................................................................................. 2-1
2.1 StandardSpecication..................................................................................... 2-1
2.2 Characteristics.................................................................................................. 2-3
2.3 ModelandSu󰀩xCodes ................................................................................... 2-4
2.4 OverhaulParts................................................................................................... 2-4
2.5 ExternalDimensionsandFlowDiagrams...................................................... 2-5
2.6 Connection Diagram....................................................................................... 2-10
2.7 Measurement Principle .................................................................................. 2-11
3. Installation................................................................................................. 3-1
3.1 Conditions for Installation ............................................................................... 3-1
3.2 InstallationMethod ........................................................................................... 3-2
3.3 Pipingconguration......................................................................................... 3-4
3.4 Wiring ................................................................................................................. 3-6
3.4.1 Grounding .......................................................................................... 3-6
3.4.2 Power Supply..................................................................................... 3-6
3.4.3 Connecting Signal Lines .................................................................... 3-6
3.4.4 Connecting Detector to Converter ..................................................... 3-7
3.4.5 Connecting Float Switch Cable of Overow Tank to Converter ........ 3-7
4. Operation................................................................................................... 4-1
4.1 Preparation for Operation ................................................................................ 4-1
4.2 Starting Operation ............................................................................................ 4-2
4.3 ShuttingDown................................................................................................... 4-3
4.3.1 For Shut Down within 7 Days............................................................. 4-3
4.3.2 For Shut Down over 7 Days............................................................... 4-3
4.4 Restarting Operation ........................................................................................ 4-3

vi
IM 12K01B02-01E
<CONTENTS>
4.4.1 For Shut Down within 7 Days............................................................. 4-3
4.4.2 For Shut Down over 7 Days............................................................... 4-3
5. Calibration................................................................................................. 5-1
5.1 Calibration Pattern and its Cycle .................................................................... 5-1
5.2 Notes regarding Calibration ............................................................................ 5-2
5.3 Calibration Screen Display .............................................................................. 5-2
5.4 Calibration of UV/VIS ........................................................................................ 5-3
5.4.1 How to Prepare Calibration Solution.................................................. 5-3
5.4.2 Common Zero Calibration.................................................................. 5-6
5.4.3 Common Span Calibration ................................................................ 5-9
5.4.4 Individual (UV) Span Calibration...................................................... 5-12
5.5 TURB (turbidity) Span Calibration ................................................................ 5-15
5.5.1 How to Prepare the Calibration Solution ......................................... 5-15
5.5.2 TURB (turbidity) Span Calibration ................................................... 5-16
6. Functions .................................................................................................. 6-1
6.1 MEAS. (Measurement) Screen......................................................................... 6-1
6.2 TableofFunctions ............................................................................................ 6-1
6.3 Maintenance Screen Display ........................................................................... 6-2
6.4 Maintenance - Setting....................................................................................... 6-3
6.4.1 Signal Allocation................................................................................. 6-3
6.4.2 Signal Input Setting............................................................................ 6-4
6.4.3 Output Setting .................................................................................... 6-5
6.4.4 Output Condition Setting.................................................................... 6-7
6.4.5 Time Adjustment ................................................................................ 6-7
6.4.6 LCD Setting........................................................................................ 6-8
6.4.7 Touch Panel Adjustment .................................................................... 6-9
6.4.8 Maker Maintenance Mode ................................................................. 6-9
6.5 Maintenance - Measurement Setting ............................................................ 6-10
6.5.1 Measuring Range Setting for each Component .............................. 6-11
6.5.2 Setting of Decimal Place for each Component................................ 6-12
6.5.3 Unit Setting for UV, VIS, and UV-αVIS............................................. 6-12
6.5.4 Setting of Turbidity Correction Factor .............................................. 6-13
6.5.5 Setting of COD Conversion Factor and Turbidity Correction Factor6-14
6.5.6 Setting of MAX Alarm Value for COD and TURB (turbidity) ............ 6-15
6.5.7 Setting of MIN Alarm Value for COD and TURB (turbidity) .................. 6-16
6.5.8 Unit Setting for TURB (turbidity) ...................................................... 6-17
6.6 Maintenance - Action...................................................................................... 6-17
6.6.1 Action ............................................................................................... 6-17
6.7 Maintenance-Check ...................................................................................... 6-18
6.7.1 Unit Information................................................................................ 6-19
6.7.2 Individual ID Setting ......................................................................... 6-19
6.7.3 External Input/Output Check............................................................ 6-19

vii
IM 12K01B02-01E
<CONTENTS>
6.7.4 Check Analog Input.......................................................................... 6-20
6.7.5 Check Analog Output....................................................................... 6-21
6.8 DataCheck....................................................................................................... 6-21
6.8.1 Log Data Check ............................................................................... 6-22
6.8.2 Log Data Deletion ............................................................................ 6-23
6.8.3 Graph Display .................................................................................. 6-24
6.8.4 Calibration Report Check................................................................. 6-25
6.8.5 Calibration Report Deletion.............................................................. 6-26
6.8.6 CF Card Transfer ............................................................................. 6-27
6.8.7 CF Card Initialization........................................................................ 6-27
6.9 Alarm ................................................................................................................ 6-28
6.9.1 Alarm Check .................................................................................... 6-29
6.9.2 Alarm Stop ....................................................................................... 6-29
6.9.3 Alarm History Check ........................................................................ 6-30
6.9.4 Alarm History Deletion ..................................................................... 6-30
7. ExternalInputandOutput ....................................................................... 7-1
7.1 Terminal diagram of input and output ............................................................ 7-1
7.2 Analog Output ................................................................................................... 7-2
7.3 Contact Input and Output................................................................................. 7-3
7.3.1 Contact Output................................................................................... 7-3
7.3.2 Contact Input...................................................................................... 7-4
7.4 SavingDatatoaCFCard ................................................................................. 7-5
8 Maintenance.............................................................................................. 8-1
8.1 Maintenance item.............................................................................................. 8-1
8.2 Maintenance of Detector .................................................................................. 8-2
8.2.1 Cleaning Method for Measuring Cell ................................................. 8-2
8.2.2 Replacement of Wiper Blade Rubber................................................ 8-4
8.2.3 Replacement of Desiccant Agent and Seal Washers for Screws...... 8-6
8.2.4 Replacement of Desiccant Agent in the Measuring Cell ................... 8-7
8.3 Cleaning of Sampling Unit ............................................................................. 8-11
8.3.1 Cleaning of Overow Tank and Measuring Tank ............................. 8-11
8.3.2 Removal of Inner Tank of Measuring Tank ...................................... 8-12
8.4 Accessories and spare parts......................................................................... 8-13
9 Troubleshooting ....................................................................................... 9-1
9.1 Table of Status and Operation ......................................................................... 9-1
9.2 Table of alarm and Operation .......................................................................... 9-1
9.3 Alarm Occurrence Condition........................................................................... 9-2
9.4 Causes and Measures for Alarm ..................................................................... 9-3
App.1 Overview............................................................................................ App.1-1
App.1.1 Cautions.....................................................................................................App.1-1
App.1.2 Composition ..............................................................................................App.1-1

viii
IM 12K01B02-01E
<CONTENTS>
App.2 Installation........................................................................................ App.2-1
App.2.1 Selecting an installation location...........................................................App.2-1
App.2.2 Cautions for installation environment....................................................App.2-1
App.2.2.1 Sample water condition ............................................................. App.2-1
App.2.2.2 Surrounding environment .......................................................... App.2-1
App.2.3 Installing UV700G .....................................................................................App.2-1
App.2.3.1 Positions of foundation bolts for pole stand ............................... App.2-1
App.2.3.2 Service and maintenance space ............................................... App.2-2
App.2.3.3 Figure of completed pole stand mount ...................................... App.2-2
App.2.3.4 Pole stand assembly.................................................................. App.2-3
App.2.3.5 Measuring tank assembly.......................................................... App.2-3
App.2.3.6 Overow tank assembly............................................................. App.2-4
App.2.3.7 Converter assembly................................................................... App.2-6
App.3 Piping................................................................................................. App.3-1
App.3.1 Piping procedure ......................................................................................App.3-1
App.4 Wiring................................................................................................. App.4-1
App.4.1 Wiring procedure ......................................................................................App.4-1
App.4.1.1 Earth connection ........................................................................ App.4-1
App.4.1.2 Power supply ............................................................................. App.4-1
App.4.1.3 Cable connection for detector.................................................... App.4-2
App.4.1.4 Float switch cable connection for overow tank ........................ App.4-2
App.4.1.5 Signal line connection ................................................................ App.4-2
Customer Maintenance Parts List......................................CMPL 12K01B02-01E
Revision Information ...............................................................................................i

<1. Overview> 1-1
IM 12K01B02-01E
1. Overview
1.1 Introduction
GENERAL
Water pollution control laws and regulations require monitoring of wastewater quality to prevent
water pollution in lakes, rivers and enclosed bodies of water. Pollutant load is an index of
water quality standards and is dened as the product of the COD (chemical oxygen demand)
concentration and the wastewater volume. Certain entities are required to measure pollutant
loads and comply with the limits.
Among various methods for COD measurement, automatic ultraviolet absorption spectrometry is
the ideal choice on the whole since it provides high correlation between analyzer and laboratory
results, measurement continuity and maintainability.
The UV700G Ultraviolet (UV) analyzer is an instrument for continuous on-line measurement
using the same cell length modulation method as its predecessor UV400G.
It provides improved operability through a wide measuring range and touch screen interface, high
reliability and excellent maintainability.
FEATURES
• Graphic LCD with touch screen on the converter provides easy interactive operation.
• Detector uses the rotary cell length modulation method. Zero check is performed at the time
of minimum cell length, virtually eliminating zero drift.
• Continuous cell cleaning with unique wiper system, allowing long term, stable
measurement.
• Analyzer covers a wide measuring range:
from 0-0.1 Abs to 0-5.0 Abs.
• Flow-through cell type for easy maintenance.
• Data memory function for transferring data to a PC via an optional compact ash (CF) card.

<1. Overview> 1-2
IM 12K01B02-01E
1.2 Description of Parts
1.2.1 Unit
Base
Measuring Tank
Overflow Tank
Converter
Hood (optional)
Detector
Door
Display
Left Side View Front View
Float Switch
CAUTION
The stanchions illustrated are typical examples. Appearance and size may vary depending on the
specication.

<1. Overview> 1-3
IM 12K01B02-01E
l Insideoftheconverter
Power / alarm LED Display (Touch panel)
Power switch
Maintenance switch
Fuse
CF card insertion slot
Connectors for the detector Signal terminals AC power terminals
.CF CARD

<1. Overview> 1-4
IM 12K01B02-01E
1.2.2 Display
This section describes the parameters shown on a typical display:
• The display is touch panel. Do not press buttons with wet hands, or a sharp object such as a
pen tip or a screwdriver.
• If no buttons are pressed for a certain period of time, the backlight turns OFF.
• If no buttons are pressed for about two hours on displays other than those for measurement,
data or alarm, the display turns to the measurement display.
l Exampleofdisplay-Displayingmeasurementreadings
The display shows measurement readings.
1
3
4
5
6
7
9
8
2
NO. Display exampleDescription
1MEAS., SETTING, LOG DATA, etc.Title of display
22004/01/30 09:57Clock
3Abs, CONC, etc.Items to be measured
4Instantaneous valuesReadings
5Conversion factors for COD, etc.Conversion factor
6MAINTENANCE, CAL, etc.Operation buttons
7WARM UP!: Unit is being warmed up.Status of unit
8RangeRange
9Abs, CONC, etc.Switchable measurement items
WARM UP!
When the power is turned ON, “WARM UP!” is displayed. This will disappear after one hour.

<1. Overview> 1-5
IM 12K01B02-01E
l Exampleofdisplay-Displayingitemstobeselected
1
2
3
NO. Display exampleDescription
1MAINTENANCE, SETTING, etc.Title of display
2SETTING, MEAS. SETTING, etc.Selection keys
3CLOSE etc.Switching keys
l Exampleofdisplay-Displayinghistoryandotherinformation
1
2
3
NO. Display exampleDescription
1Alarm history, calibration report, etc.Title of display
2Description of alarms, etc.Items to be displayed
3–Data list

Blank Page

  <2.Specication> 2-1
IM 12K01B02-01E
2. Specication
2.1 StandardSpecication
Measurement : Organic pollutants in wastewater.
Measurement method:
Dual optical path, dual wavelength, rotary cell length modulation method
Measurement wavelength:
Ultraviolet (UV): 253.7 nm
Visible light (VIS): 546.1 nm
Light source: Low pressure mercury-vapor lamp
Detector: Silicon photo cell, ow-through type
Measuring range (corrected for 10 mm cell)
UV/VIS absorbance 0-0.1 to 0-5.0 Abs
Display: Graphic LCD with touch screen,
320  240 dot, with backlight
Indication: UV absorbance, VIS absorbance, UV- VIS absorbance, COD
concentration, turbidity
Resolution: 0.0001 Abs (factory default) or 0.001 Abs
COD conversion: Conversion equation Y = a bX
where Y= COD concentration
X = absorbance (UV-VIS)
Turbidity conversion: Conversion equation Y = a bX
where Y = turbidity,
X = absorbance(VIS)
Analog output:
Number of outputs: 3
Functions: 3 functions selectable:
UV absorbance / VIS absorbance/ UV-VIS absorbance / COD
concentration / turbidity
Specications: 4-20 mA DC or 0-16 mA DC, isolated
(non-isolated between channels)
Contact output:
Number of outputs: 6
Functions:
2 functions xed:
Power o󰀨, maintenance status
4 functions selectable:
Total alarm / COD high alarm / turbidity high alarm / light souse
malfunction / no sample / cleaning motor error / analyzer error
Descriptions:
Power o󰀨:
Activated when power o󰀨 occurs
Maintenance status:
Activated when instrument is in maintenance or calibration mode or
when MAINTENANCE switch is turned on
Total alarm:
Cleaning motor error, light source malfunction and / or analyzer error

  <2.Specication> 2-2
IM 12K01B02-01E
Specications: Voltage-free contact output, Form A
Contact rating: 0.3 A / 125 V AC, 1A / 30 V DC (resistive load), independent
common at each output
Contact input:
Number of inputs: 2
Functions: No sample oat switch, time adjustment
Specications: Voltage-free contact input (open collector can be connected), isolated
On resistance: 100 V max.
Open circuit voltage: 5.5 V DC
Short circuit current: 5 mA max.
Data memory: Measured data can be stored in converter and stored data transferred to
CF card.
Log interval: 1 min or 1 hour
Log time: On the hour every hour
Retention time: Approx. 10 days for 1 min interval
Approx. 1 year for 1 hour interval
Calibration method: Manual calibration using zero / span standard (calibration solution in
ampoule) (One touch calibration is available)
Cleaning method: Automatic, continuous wiper cleaning
Operating conditions:
Ambient temperature:0 to 40 8C
Ambient humidity: 90% RH or less
Installation location: Flat, stable place not subject to severe vibration or shock. Allow pace for
maintenance. No dust, mist, corrosive gases are present. Atmospheric
pressure. Avoid exposure to direct sunlight. Good ventilation. Max.
altitude of 2000 m.
Sample conditions:
Temperature: 2 to 40 8C (non-freezing)
Pressure: 20 to 500 kPa
pH: 4 to 10
Flow rate: 2 to 20 L/min
Concentration of suspended solids:
200 mg/L or less
Note: Protection against freezing should be provided when needed.
Piping connection:
Analyzer with pole-base mount type (UV700G-A-A)
Sample inlet: Rp 1/2 female
Bypass outlet: Rc 1/2
Overow outlet 1: 13A nominal, elbow tting
Overow outlet 2: 20A nominal, elbow tting
Drain port: Rc 1/2
Discharge port: 50A nominal, tube tting
Analyzer with standard self-supporting type (UV700G-hB-A)
Sample inlet: Rp 1/2 female
Drain port: Rc 1/2
Discharge port 1: 50A nominal, tube tting
Discharge port 2: VP40 pipe

  <2.Specication> 2-3
IM 12K01B02-01E
Wiring:
Power wiring:
Size: 1.25 mm2 (AWG16) or larger
Connection: M4 screw terminal
Termination: Crimp terminal for M4 screw
Signal wiring:
Size: 0.08 to 1.5 mm2 (AWG28 to 16)
Connection: Pin terminal
Termination: Strip 7 mm of insulation o󰀨 wire end
Dimensions (excluding projections):
Converter: 240(W) 3 104(D) 3 320(H) mm
Detector: 200(W) 3 180(D) 3 403(H) mm
Materials (main materials):
Wetted parts: SUS304, R-PVC, fused silica, polypropylene, chloroprene rubber,
titanium (when option code “/TN” is specied)
Stanchion
Material:
Pole-base mount type (UV700G-hA-A):
Iron
Standard self-supporting type (UV700G-hB-A):
Carbon steel plate
Finish:
Converter: Epoxy with modied melamine resin, baked, Munsell 5PB8/1 equivalent
Pole-base mount type (UV700G-hA-A):
Epoxy with modied melamine resin, baked, Munsell N1.0 equivalent
Standard self-supporting type (UV700G-hB-A):
Polyurethane resin, baked, Munsell 0.6GY3.1/2.0 equivalent
Construction: Outdoor installation (equivalent to IP54)
Weight:
Converter: Approx. 5.0 kg
Detector: Approx. 5.6 kg
Pole-base mount type:
Approx. 31 kg
Standard self-supporting type (including converter, detector, overow tank):
Approx. 47 kg
Power supply: 100 to 230 V AC 610%, 50/60 Hz
Grounding: JIS Class D grounding (100 V or less, φ1.6 mm copper wire)
Power consumption:  100 to 120 V AC, 45 VA max.
200 to 230 V AC, 60 VA max.
2.2 Characteristics
Linearity: 62% FS (65% FS for 2.6 to 5.0 Abs)
Repeatability: 62% FS (65% FS for 2.6 to 5.0 Abs)
Stability: 62% FS/24 h (65% FS/24 h for 2.6 to 5.0 Abs)
Response time: 90% within 1 min (sample ow rate at 5 L/min)

  <2.Specication> 2-4
IM 12K01B02-01E
2.3 ModelandSu󰀩xCodes
Model Su󱐰x
Code
Option Code Description
UV700G - - - - - - - - - - - - - - - - - - - - UV analyzer (organic pollutant analyzer)
Language -J
-E
- - - - - - - - - - -
- - - - - - - - - - - Japanese
English
Stanchion N
A
B
- - - - - - - - - - -
- - - - - - - - - - -
- - - - - - - - - - -
Without stanchion
Pole-base mount type
Standard self-supporting type2
/
-A - - - - - - - - - - - Always -A
Option /H
/TN
Hood for sun protection
Titanium wetted parts*1
*1: Should be selected when sample water contains seawater or chlorine.
See “8.4 Accessories and spare parts” regarding Standard Accessories and Auxiliary parts.
2.4 OverhaulParts
For one year after delivery no parts are required to be replaced except wiper blade rubbers and
desiccants. To ensure reliable measurement with simple routine maintenance, it is recommended
that the instrument be overhauled every year by Yokogawa. The table below lists parts required
for overhaul.
Item P/N Qty Description
Inspection parts kit K9436CA 1 set
Contents:
V-ring A
Seal washer
Seal washer
Roller
Cell packing 2
Desiccant (cell)
Wiper blade rubber
Light source
Desiccant (detector)
Stepping motor
Blind cap
Case packing
K9430EP
K9436CB
K9430ES
K9430EN
K9430ER
K9430EH
K9436CG
K9436FY
K9430EG
K9436GB
K9436GR
K9436GK
2 pcs/set
4 pcs/set
10 pieces
6 pieces
4 pcs/set
2 pcs/set
4 pcs/set
1 piece
5 pcs/set
1 piece
4 pcs/set
1 piece
Cell
Detector’s upper case
Cell
Cell
Cell
Cell
Cell
Cell
Cell
Detector
Detector, case
Detector, case
Note: For yearly overhaul, it is recommended that an inspection parts kit (P/N K9436CA) be purchased.
The kit does not include calibration solutions, which should be purchased separately.

  <2.Specication> 2-5
IM 12K01B02-01E
2.5 ExternalDimensionsandFlowDiagrams
1. UVAnalyzerwithpole-basemounttype,UV700G-A-A
n ExternalDimensions  Unit: mm
*Hood for sun protection is optionally available.
(160)(285)
320
10
400350-500
260
20
(209)
(60)
140
(390)
(520)
340
)(248
(345)
300
(1506)
1
2
3
4
5
6
7
8
9
10 11
12
13
14
15
16
17
18
19
20
*
Weight: Approx. 31 kg
300 (1000)1000 26020
32010
340 (1000)500
1840
2300
42-ø9
M8
Basic Anchor Bolt Plan
Maintenance Area
Front
OptionalHood for sun protection
Float switch
20
19
18
17
16
15
No. Item Description
1 Converter
2 Wiring port
3 Pole
4 Overflow tank
5 Detector
6 Drain port (V-4) Rc 1/2
7 Discharge port 50A nominal, tube fitting
8 Ball valve (V-1)
9 Ball valve (V-2)
10 Bypass outlet Rc 1/2
11 Blind plate
12 Measuring tank
13 Sample inlet Rp 1/2 female
14 Detector table
Base
Overflow outlet 2 20A nominal, elbow fitting
Overflow outlet 1 13A nominal, elbow fitting
Ball valve (V-3)