YOODA 28LEQ Series User manual

LE type motors equipped with a radio receiver are wireless
and can be controlled with a remote. They are designed for
automation of blinds. They have electronic limit switches
which are programmed by the remote control. The built-in
rechargeable battery allows you to mount the drive without
having to power it. LE type motores are compatible with all
YOODA transmitters.
Radio receiver memory:
up to 20 transmitters
Power supply:
12 V DC
Operating temperature:
from -5°C to 50°C
Protection degree:
IP 40
Load:
up to 6 kg
28 LEQ motor with radio receiver and with battery
Non-compliance with the specification might cause risk for life or health and can determine proper work of the blind.
We strongly recommend to comply with the specification.
28LEQ SERIES TUBULAR MOTOR
www.sukcesgroup.pl
1. General information
Programming button functions:
1. Pressing the programming button briefly for approximately 1 second controls the drive step by step.
2. Press the programming button for 2 seconds to enter the first transmitter programming mode.
3. Pressing the programming button for 6 seconds changes work motor direction.
4. Pressing the programming button for 11 seconds deletes the motor memory and restores the factory settings.
1
battery motor gear
antenna
charging socket
radio receiver,
limit switches system
programming button

Motor should be mounted in places protected from unfavourable weather conditions. Do not pull the motor head when
removing it from the tube.
1. Cut the tube
to the proper length.
2. Deburr the edges
and remove the metal residue.
3. Place the adaptation
on the motor.
4. Measure the distance (L)
between the inner edge of motors head
and the end of the motors adaptor.
5. Insert the motor into the tube
up to the point of connection
between the edge of the tube and
the inner edge of the motors head.
6. Attach the tube to the
coupling part of the adaptation.
2. Safety measures
3. Placing motor in the tube
Before installing or using motor please read the following instruction. The installer must comply with the standards and regulations in
force in the country where the appliance will be installed and provide information to users about the conditions and maintenance of the
device. Failure to follow these instructions can present risk to life and health, or invalid functioning of the roller shutter. This also results
in the loss of warranty rights.
Motors torque parameter should be adequate
to the weight of the roller shutter curtain.
Do not hit the motor. Reduce the vibration
of the motor to a minimum.
Electrical system control should be performed
regularly to detect any signs of use or damage
of the motor.
All contact of the motor with any liquids
should be reduced to minimum.
No tools should be used when
placing motor in the tube.
During the adapter montage special attention
must be paid not to damage the motor.
Motor and its control system should
be kept out of children reach.
4. Charging
1. It is recommended to charge the battery by min. 3 hours.
2. Ensure that the drive is fully charged before initial startup.
3. Charge the battery at least once every 6 months.
4. Use only power supply, dedicated to the device. Using another power supply may damage the motor.
2

Connect the motor
to the power supply.
During charging, the LED diode
on the power supply light is red.
When the battery is fully charged,
the LED diode will turn to green.
5. Range
6. Programming first transmitter
7. Changing motors direction
Radio receiver range is a variable value and can differ from declared values depending on conditions in which device
operates. Possible sources of changes in range are building construction, interference caused by other radio transmitters
etc.
12 V DC 200 m 35 m 433,92 MHz
L1
outdoor L2 indoor Operating frequency
20
Blind with remotely controlled motor
L2L1
1. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from
programming mode without saving any changes.
2. Programming the first transmitter removes the previously programmed transmitters from memory.
Turn on the power or press the
programming button on the
motor head.
Bilnd will make
short up/down
movements.
Motor will
make a sound.
Bilnd will make
short up/down
movements.
Motor will
make a sound.
Press
programming button P2
on the remote control.
Bilnd will make short
up/down movements.
Motor will make
several sounds.
Motor will
make a sound.
Press programming
button P2 on the
remote control.
Press
UP button.
When pressing DOWN
button blind moves up.
When pressing
DOWN button
blind moves down.
Blind will
make up/down movement.
Motor will
make a sound.
Press and hold
for about 6 seconds
programming button
on the motor head.
3

8. Programming limit positions
9. Removing limit positions
10. Programming the third limit position
4
To set the upper and lower limit position press the programming button P2 during the motor movement, it causes the work displacement.
Then you can precisely set the limit positions. Pressing the P2 button again motor will run continuously.
Press
programming
button P2.
Press
UP button.
Press
programming
button P2 again.
Upper limit position
Press
UP button.
Blind will make up/down
movement. Motor will
make a sound.
Blind will make up/down
movement. Motor will
make a sound.
Blind will make up/down
movement. Motor will make
a few short sounds
When the blind
reaches upper limit position
press STOP button.
Blind will make up/down
movement. Motor will
make a sound.
Blind will make up/down
movement. Motor will
make a sound.
Press STOP button
5 times at 0.5 sec
intervals to confirm
the upper limit position.
Press
STOP button
5 times at 0.5 sec
intervals to confirm
the lower
limit position.
Press
DOWN button.
Limit positions
has been
programmed.
Lower
limit position.
When the blind
reaches lower
limit position
press STOP button
Blind will make up/down
movement. Motor will
make a sound.
Blind will make up/down
movement. Motor will
make a sound.
Blind will make up/down
movement. Motor will make a few short
sounds
Limit positions
has been removed.
Press
programming
button P2
Press
programming
button P2 again.
Press
DOWN button.
1. After setting the upper and lower limit positions, it is possible to set the third position (favorite) between those positions.
2. Hold the STOP button for 3 seconds to set the blind in third limit position.
3. When the motor is in pulse mode, hold the STOP button for 3 seconds, blind reaches lower limit position, and then to the set third
position
Blind will make up/down
movement. Motor will
make a sound.
Blind will make up/down
movement. Motor will make
a few short sounds.
Favourite position
has been set.
Press
STOP button.
Press
STOP button.
Blind will
make up/down
movement.
Upper limit position
has been set.
Lower limit position
has been set.
An example of the third
limit position
Set the blind
in favourite position.
Press
programming
button P2.

11. Removing third limit position
12. Programming another transmitter
13. Deleting another transmitter
14. Deleting motor memory
5
Blind will make up/down
movement. Motor will
make a sound.
Blind will make up/down
movement. Motor will
make a sound.
Blind will make up/down
movement. Motor will make
a few short sounds.
Favourite position
has been removed.
Press
programming
button P2.
Press
STOP button.
Press
STOP button.
1. Receiver can be controlled by up to 20 transmitters.
2. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from programming
mode without saving any changes.
Blind will make
up/down movement.
Motor will make a sound.
Blind will make
up/down movement.
Motor will make a sound.
Blind will make
up/down movement.
Motor will make
a few short sounds.
Press programming
button P2 on the
A remote control.
Press programming
button P2 on the
A remote control.
Press programming
button P2 on the
B remote control.
Remote control
has been programmed.
Blind will make
up/down movement.
Motor will make a sound.
Blind will make
up/down movement.
Motor will make a sound.
Blind will make
up/down movement.
Motor will make
a few short sounds.
Press programming
button P2 on the
A remote control.
Press programming
button P2 on the
A remote control.
Press programming
button P2 on the
B remote control.
Remote control
has been removed.
1. Deleting memory of motors radio receiver will cause for all programmed transmitters to be lost.
2. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from programming
mode without saving any changes.
Blind will make up/down
movement. Motor will
make a sound.
Blind will make
up/down movement.
Motor will make a sound.
Blind will make
up/down movement.
Motor will make
a few short sounds.
All active transmitters have
been removed from memory.
Press programming
button P2 on any
remote control.
Press
STOP button.
Press programming
button P2 on
remote control.

15. Activating impulse mode
16. Programming key-ring remotes
6
1. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from programming
mode without saving any changes.
2. To reverse this procedure please repeat the instruction.
Blind will make up/down
movement. Motor will
make a sound.
Press programming
button P2 on any
remote control.
Press
DOWN button.
Blind will make
up/down movement.
Motor will make a few
short sounds.
When motor is in
impulse mode single push of
a button on the remote will
cause motor to make
short move.
Press
UP button.
Blind will make up/down
movement. Motor will
make a sound.
1. When programming key-ring remotes that do not have additional P2 programming button the same function is substituted with
simultaneous push of STOP and UP buttons.
2. Longer than 5 seconds pause between series of button clicks during programming will cause device to switch off from programming
mode without saving any changes.
Blind will make up/down
movement. Motor will
make a sound.
Blind will make up/down
movement. Motor will
make a sound.
Blind will make
up/down movement.
Motor will make a few
short sounds.
Motor will
make a sound.
Press
UP button.
Press simultaneously
STOP and UP
programming buttons.
Press simultaneously
STOP and UP
programming buttons.
Press and hold
for about 2 seconds
programming button
on the motor head.