York Fitness Ti-Co User manual

Ti-Co
O WN E R ”S
M A N UA L

-1-

-2-
PART LIST
PART NO: DESCTIPTION Q’TY
1 MAIN BASE 1
2 GUIDE ROD 2
3 LEFT BASE 1
4 RIGHT BASE 2
5 SELECTOR SHAFT 1
6 TOP PLATE 1
8 WEIGHT STACK 9
9 RUBBER DOUNT 2
10 VERTICAL BEAM 1
12 TOP CROSS BEAM 1
13 SEAT ASSEMBLY UNIT 1
14 LEG EXTENSION/ARM CURL BAR 1
15 PRESS BAR 1
16 LEFT PEC DECK ARM 1
17 RIGHT PEC DECK ARM 1
18 PRESS PIN 1
19 SEAT 1
20 BACK SEAT 1
21 PULLEY BLOCK 2
22 FLOATING PULLEY BLOCK(A) 1
23 FLOATING PULLEY BLOCK(B) 1
24 CABLE2535mm 1
25 CABLE3630mm 1
26 CABLE2970mm 1
27 CHAIN 2
28 PEC DECK PAD 2
29 LEG EXTENSION/CURL PAD 4
30 LAT BAR 1
31 CURL BAR 1
32 PAD HOLDER 2
33 PULLEY 12
35 CHAIN HOOK 4
36 HAND GRIP 8
37 RUBBER BUMPER 2
38 1”ROUND BUSHING 1
39 PLASTIC BUSHING 6
40 1” ROUND END CAP 4

-3-
PART LIST
PART NO: DESCTIPTION Q’TY
41 50MM SQUARE END CAP 10
42 RUBBER END CAP 2
43 HANDLE PIPE 2
44 PIN FOR WEIGHT SATCK 1
45 38MM SQUARE END CAP 2
46 PRESS BAR SHAFT 1
47 QUICK PIN 1
48 M10*45mm HEX BOLT 9
49 M12*80mm HEX BOLT 1
50 M10*75mm HEX BOLT 6
51 M10 NUT 2
52 M8*40mm HEX BOLT 1
53 M10*70mm HEX BOLT 7
54 M10*25mm HEX BOLT 6
55 OD48mm*ID13mm WASHER 1
56 M10*65mm HEX BOLT 3
57 M8*65mm HEX BOLT 2
59 M8*15mm HEX BOLT 4
60 M12 NYLON NUT 1
61 M16 NYLON NUT 4
62 M10*35mm HEX BOLT 2
63 M10 NYLON NUT 27
64 M8 NYLON NUT 1
65 M16 WASHER 4
66 M12 WASHER 2
68 M10 WASHER 60
69 M8 WASHER 6
70 RUBBER CAP 2
71 OIL BUSHING 8
72 STEEL PLATE 2
73 ANKLE STRAPE 1
74 SQUARE CAPψ26x□38 MM 2
75 BUFFER 40x40 MM 2
76 TOOL 2

-4-
STEP 01
1. PLACE RUBBER CAP (42) INTO BOTH ENDS OF LEFT BASE (03)
2. INSERT GUIDE RODS (02) ONTO LEFT BASE (03) USE BOLT (54) WITH
WASHER (68).
3. ATTACH MAIN BASE (01) ONTO LEFT BASE (03) USE BOLT (50) WITH
WASHER (68) AND NUTS (63).
FASTEN ALL BOLTS BY USING TOOL.
4. ATTACH VERTICLE BEAM (10) ONTO MAIN BASE (01) USE BOLT (53) WITH
WASHER (68) AND NUTS (63).

-5-
STEP 02
1. ATTACH THE RUBBER DOUNT (09) INTO THE GUIDE ROD (02).
2. SLIDE THE WEIGHT PLATE (08) AND TOP PLATE (06) OVER GUIDE ROD (02).
GROOVE FOR SELECTOR PIN ON WEIGHT PLATES SHOULD FACE DOWN
3. INSTALL 1”ROUND BUSHING (38) INTO THE SELECTOR SHAFT (05).
WITH PIN (47) THEN ATTACH THE SELECTOR SHAFT (05) INTO THE TOP
PLATE (06).
4. PLACE 2" SQUARE CAP (41) INTO BOTH ENDS OF MAIN BASE (01).
5. PLACE RUBBER CAP (70) INTO BOTH ENDS OF RIGHT BASE (04).
6. ATTACH RIGHT BASE (04) TO MAIN BASE (01) USE BOLT (50) WITH
WASHER (68) AND NUTS (63).AS SHOWN.

-6-
STEP 03
1. PLACE 2" SQUARE CAP (41) INTO BOTH ENDS OF TOP CROSS BEAM (12).
2. ATTACH TOP CROSS BEAM (12) ONTO THE VERTICLE BEAM (10) USE BOLT
(53) WITH WASHER (68) AND NUTS (63). FROM TOP SIDE AND CONNECT THE
GUIDE RODS (02) TO THE TOP CROSS BEAM (12) USE BOLT (54) WITH
WASHER (68) AS SHOWN.
3. ATTACH RUBBER BUMPER (37) TO THE VERTICLE BEAM (10).
4. ATTACH PULLEY BLOCK (21) TO THE VERTICLE BEAM (10), USE BOLT (56)
WITH WASHER (68) M10 NUTS (63).
5. INSTALL PRESS PIN (18) TO THE VERTICLE BEAM (10) WITH BOLT (56),
WASHER (68) NUTS (63) AS SHOWN.

-7-
STEP 04
1. PLACE 50MM SQUARE CAP (41) INTO BOTH ENDS OF LEG EXTENSION
/ARM CURL BAR (14).
2. ATTACH SEAT ASSEMBLY (13) TO VERTICLE BEAM (10), WITH BOLTS
(50), NUTS (63), AND WASHERS (68) AS SHOWN.
3. ATTACH LEG EXTENSION /ARM CURL BAR (14) TO SEAT ASSEMBLY (13).
4. ATTACH BACK SEAT (20) TO VERTICLE BEAM (10) AS SHOWN.
5. ATTACH SEAT (19) TO SEAT ASSEMBLY (13) AS SHOWN.
6. SLIDE PAD HOLDERS (32) INTO THE HOLE PROVIDED.
7. SLIDE LEG EXTENSION/CURL PADS (29) ONTO PAD HOLDERS (32).
8. PLACE 1" ROUND CAP (40) INTO PAD HOLDERS (32).

-8-
STEP 05
1. PLACE 50MM SQUARE CAP (41) INTO BOTH ENDS OF PRESS BAR (15).
2. INSTALL OIL BUSHING (71) INTO THE PRESS BAR (15) AS SHOWN.
STEP 06
1. ATTACH PRESS BAR (15) TO TOP CROSS BEAM (12) WITH PRESS BAR
SHAFT (46) AND OIL BUSHING (71) WASHER (65) BOLT (61) AS SHOWN.
2. ATTACH PEC DEC PADS (28) AND HAND GRIP (36) SLIDE ONTO PEC DEC
ARM (16&17).
3. ATTACH HANDLE PIPE (43) AND HAND GRIP (36) TO PEC DEC ARM
(16&17) WITH BOLT (54), WASHER (68) AS SHOWN.
4. INSTALL PEC DEC ARM (16&17) TO PRESS BAR (15) WITH WASHER (65)
AND NYLON NUTS (61) AS SHOWN.

-9-
PLEASE ENSURE THE CABLE (26) CAN BE ROTATING FREELY AFTER INSTALLED.
PLEASE FOLLOW THE ASSEMBLING INSTRUCTION WITH THE CABLE (26) , M10 HEX BOLT
(62) , M10 NUT (51) , M10 WASHER (68) ANDM10 NYLON NUT (63) ARE PLACED IN CORRECT
POSITION AS THE DRAWING SHOWN , FAILURE TO DO SO WILL RESULT IN THE CABLE
AND CABLE EYELET COMING OFF. THIS WILL NOT BE COVERED BY THE WARRANTY.

-10-

-11-
---CABLE ASSEMBLY---
1.START WITH THE TOP LONG CABLE 2535mm (24)
START BY THREADING THE END OF THE CABLE WITHOUT THE BALL OVER.
PULLEY NO.1, OVER PULLEY NO.2, DOWN AND AROUND PULLEY NO.3 IN
FLOATING PULLEY LOCK, UP AND OVER PULLEY NO.4 AND DOWN AND
ATTACH TO WEIGHT STACK WITH M12 BOLT & WASHER (55) AS SHOWN.
2. START THE BOTTOM MEDIUM SIZE CABLE 3630mm (25)
START BY THREADING THE END OF THE CABLE WITHOUT THE BALL UNDER
PULLEY NO.5, UNDER PULLEY NO.6, UP AND AROUND PULLEY NO.7, IN
FLOATING PULLEY BLOCK, DOWN AND UNDER PULLEY NO.8, UP AND
AROUND PULLEY NO.9 IN FLOATING PULLEY LOCK, DOWN AND WITH HOOK,
CHAIN TO END OF CABLE.
3. CONNECT THE PEC DEC CABLE 2970mm (26)
TAKE PEC DEC CABLE AND BOLT ONE END TO PEC DEC ARM AS PICTURED IN
PEC DEC ASSEMBLY, USING M10*35mm HEX BOLT (62), M10 NUT (51), M10
WASHER (68) &M10 NYLON NUT (63) TO SECURE CABLE TO ASSEMBLY, THEN
THREAD THE OTHER END OF CABLE OVER PULLEY NO.10 DOWN AND AROUND
PULLEY NO.11 IN PEC DEC PULLEY BLOCK (22) UP & OVER PULLEY NO.12 &
BOLT, CABLE TO PEC DEC ARM AS PICTURED IN PEC DEC ASSEMBLY, USE
M8*45mm HEX BOLT (52),M8 WASHER (69) & M8 NLYON NUT (64) TO SECURE
CABLE.
NOTE: IF YOU FIND THAT THE CABLES ARE NOT LONG ENOUGH, USE THE
SHORT EXERCISE CHAIN AS AN EXTENSION WITH PEAR SHAPED HOOK
AS CONNECTORS.
ATTACH HAND GRIP (36) TO LAT BAR ((30) AND CURL BAR (31).
※ WARNING: MAAKE SURE ALL CABLES DO NOT RUN OUT OF TRACK FROM
ANY OF PULLEYS WHILE YOU ARE IN USE EVERYTIME.

-12-
ARM CURL
PART LIST
PART NO: DESCRIPTION Q’TY
59 M8 *20MM HEX BOLT 2
69 M8 W ASHER 2
77 ARM CURL CUSHION 1
78 ARM CURL SUPPO R T FRAME 1
79 50*38MM PLASTIC SQUARE BUSHING 1
80 KNOB BOLT 1
1. PLACE PLASTIC SQUARE BUSHING (79) INTO LEG EXTENSION/ARM CURL
BAR (14) AS SHOWN.
2. ATTACH ARM CURL CUSHION (77) TO ARM CURL SUPPORT FRAME (78)
USING WASHER (69) HEX BOLT (59) AS SHOWN.
3. PLACE ARM CURL SUPPORT FRAME (78) INTO LEG EXTENSION/ARM CURL
BAR (14) SECURE WITH KNOB BOLT (80).
4. BY SIMPLY REMOVING THE ADJUST KNOB BOLT (80), YOU HAVE THE
OPTION OF EXERCISING WITH THE ARM CURL OR LAT TOWER.

-13-