Zamel Exta SOS-01 User manual

LIGHT SENSOR SOS-01 INSTRUCTION
Zakład Mechaniki i Elektroniki
ZAMEL sp.j.
J.W. Dzida, K. Łodzińska
ul. Zielona 27, 43-200 Pszczyna, Poland
Tel. [phone], Fax [phone]
www.zamelcet.com, e-mail: [email protected]
VER. 001_31.03.2010
The device must be
installed in accordance
with standards valid in
a particular country.
The device should be
connected according
to the details included
in this operating manual. Installation,
connection and control should be car-
ried out by a qualied electrician staff,
who act in accordance with the servi-
ce manual and the device functions.
Disassembling of the device is equal
with a loss of guarantee and can cau-
se electric shock. Before installation
make sure the connection cables are
not under voltage. The cruciform head
screwdriver 3,5 mm should be used to
instal the device. Improper transport,
storage, and use of device inuence
its wrong functioning. It is not advisa-
ble to instal the device in the following
cases: if any device part is missing or
the device is damaged or deformed. In
case of improper functioning of the de-
vice contact the producer.
CAUTION
APPEARANCE
FEATURES
TECHNICAL DATA
DESCRIPTION
SOS-01 light sensor is used to co-
operate with twilight switches WZM-
01, WZM-02, WZH-01, WZN-01 pro-
duced by ZAMEL. It measures the
luminous ux density outside and
passes/ directs the signal straight to
the twilight switch.
The light sensor is set in a herme-
tic casing in order to work in difcult
weather conditions (IP 54). It is mo-
unted by means of attached screws
on the surface.
SOS-01
Terminal clamps: IN, IN
Maximum sensor cable length: 50 m (MTY 2 x 0,5 mm2)
Light sensor: inner
Number of terminal clamps: 2
Section of connecting cables: 0,2 ÷ 2,50 mm2
Ambient temperature range: -20 ÷ +45 oC
Operating position: freely
Casing mounting: 2x stretcher 6x(3,5x35)
Casing protection degree: IP54 (EN 60529)
Protection level: II
Overvoltage category: II
Pollution degree: 2
Surge voltage: 1 kV (EN 61000-4-5)
Dimensions: 84x68x43 mm
Weight: 0,05 kg
Reference standard: EN 60669-1
EN 60669-2-1
EN 61000-4-2,3,4,5,6,11
● Hermetic casing (IP 54),
● cooperation with twilight switches
WZM-01, WZM-02, WZH-01,
WZN-01 produced by ZAMEL,
● surface mounting,
● terminal clamps 0,2 ÷ 2,50 mm2.
Light sensor
Output terminals
(IN, IN)
Photoresistor
The symbol means selective
collecting of electrical and
electronic equipment. It is forbidden
to put the used equipment together
with other waste.

VER. 001_31.03.2010
DIMENSIONS
MOUNTING, FUNCTIONING
1. Disconnect power supply by the
phase fuse, the circuit-breaker or
the switch- disconnector combined
to the proper circuit.
2. Check if there is no voltage on
connection cables of the twilight
switch cooperating with a light
sensor by means of a special
measure equipment.
3. Unscrew the cover.
4 Put the installation cables through
rubber gland.
5. Fasten the SOS-01 device to the
base by means of screws.
6. Connect the cables with the termi-
nals in accordance with the instal-
ling diagram.
7. Tighten the cover screws.
8. Switch on the power supply from
the mains for the twilight switch.
The device is ready to work after
correct mounting and connecting. Ad-
just demanded switch on time on the
twilight switch cooperating with the
SOS-01 light sensor. (WZM-01, WZM-
02, WZH-01, WZN-01 produced by
ZAMEL).
CONNECTION
APPLICATION
Typical application:
SOS-01 light sensor in cooperation with WZM-02 twilight switch operating light control functions
(e.g. garden lighting). The light sensor should not be installed in a place directly illuminated by
lamps.
LIGHT
SENSOR
LIGHT
SENSOR
68
84
43
Ø3
52
Luminous ux
density 200 lx 35 lx 20 lx 2 lx
Potentiometer
adjustment min. max.
☼
min. max.
☼
min. max.
☼
min. max.
☼
SENSOR FAMILY
Sensor: Cable length:
SOH-01 1 m
SOH-03 3 m
SOH-05 5 m
SOS-01 none
WARRANTY CARD
There is 24 months guarantee on the product
Salesman stamp and signature, date of sale
1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product.
2. The manufacturer’s guarantee does not cover any of the following actions:
a) mechanical damage during transport, loading / unloading or under other circumstances,
b) damage caused by incorrect product mounting or misuse,
c) damage caused by unauthorised modications made by the PURCHASER or any third parties to the product or any other devices
needed for the product functioning,
d) damage caused by Act of God or any other incidents independent of the manufacturer.
3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J.
4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation.
5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return.
6. The manufacturer’s guarantee is valid in the Republic of Poland.
7. The PURCHASER’s statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or
otherwise are not affected by this warranty.