Zamel EXTA EDM-01 User manual

EDM - 01 SIGNALLING MODULE INSTRUCTION MANUAL
Zakład Mechaniki i Elektroniki
ZAMEL sp.j.
J.W. Dzida, K. Łodzińska
ul. Zielona 27, 43-200 Pszczyna, Poland
Tel. [phone], Fax [phone]
www.zamelcet.com, e-mail: [email protected]
FEATURES
TECHNICAL DATA
DESCRIPTION
APPERANCE
ی Applicable in signalling systems ,
ی Continuous duty acoustic module ,
ی Supplied directly from 230 V AC
network,
ی High sound level,
ی Single-module casing
,
ی Mounted on TH 35 rail .
The EDM-01 signalling module may
be used in various systems, where
acoustic alarm is needed, e.g. as an
alarm signalling device. The module
is very flexible and applicable in
many circuits owing to the fact that
it is supplied directly from 230 V AC
network.
EDM - 01
Power terminals: L, N
Rated voltage: 230 V~
Rated voltage tolerance: -15 ÷ +10 %
Rated frequency: 50 / 60 Hz
Rated current: 15 mA
Load supply indicator: piezoelectric loudspeaker
Connection terminals quantity: 2
Connection wire section: 0,2 ÷ 2,50 mm2
Operating temperature: -20 ÷ +45 oC
Operating position: optional
Casing fastening: TH 35 rail (according to PN-EN 60715)
Casing IP: IP20 (PN-EN 60529)
Protection class: II
Overvoltage category: II
Pollution level: 2
Dimensions: single-module (17,5 mm) 90x17,5x66 mm
Weight: 51 g
Standard conformity: PN-EN 60669-1; PN-EN 60669-2-1
PN-EN 61000-4-2,3,4,5,6,11
Piezoelectricloudspeaker
Power terminal (L)Power terminal (N)
The device should be
connected to a single-
phase system accordin-
gly to current standards.
The device connections
will be described in this
manual. Only qualied electricians are
allowed to mount, connect and adjust
the bell. It is necessary to read this ma-
nual before the device mounting. Do not
disassembly the timer casing or you will
lose any warranty rights and expose
yourself to the electric shock hazard.
Before mounting operation make sure
of disconnecting the connection wires
from the electric network. Use a cross-
head screwdriver of 3.5 mm diameter
to mount the device. The bell should
be carried, stored and used in an ap-
propriate way. Do not mount the bell in
case of any device parts lack, damage
or deformation. In case of malfunction
please notify the manufacturer.
CAUTION

ASSEMBLY, OPERATION
APPLICATIONCASING DIMENSIONS
PRODUCT FAMILY
The EDM-01 signalling module is a mem-
ber of the EDM family.
1. Disconnect the electric network
by means of an appropriate cut-
off, current-limiting circuit-brea-
ker or separator.
2. Check if there is no any vol-
tage between power leads by
means of an appropriate gau-
ge.
3. Mount the EDM-01 module on TH
- 35 rail.
4. Connect the system leads accor-
ding to the electrical diagram.
5. Connect power supply circuit.
The device is ready to work just
right after its appropriate connecting.
An internal piezoelectric loudspea-
ker is ON after the module supplying
with 230 V~ voltage. The speaker is
OFF when power supply is OFF.
CONNECTIONS TIME DIAGRAMS
UNIT DIAGRAM
Device version:
01 - continuous op
02 - resettable
03 - bell
Device type
EDM - xx
L
N
L
N
The circuit warns against motor switch-OFF.
After the motor star by means of MOM-02
module, the PCM-01 counts preset time
(e.g. 10 s). During this period the EDM-01
module generates acoustic signal. When the
preset time is over, the sound will be OFF
and the motor starts.
PSU
WARRANTY
The product warranty is for a period of 24 months
Dealer signature & stamp, purchase date
1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product.
2. The manufacturer’s guarantee does not cover any of the following actions:
a) mechanical damage during transport, loading / unloading or under other circumstances,
b) damage caused by incorrect product mounting or misuse,
c) damage caused by unauthorised modications made by the PURCHASER or any third parties to the product or any other devices
needed for the product functioning,
d) damage caused by Act of God or any other incidents independent of the manufacturer.
3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J.
4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation.
5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return.
6. The manufacturer’s guarantee is valid in the Republic of Poland.
7. The PURCHASER’s statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or
otherwise are not affected by this warranty.