Zamel supla SRW-01 User manual

Wi-Fi
roller blind
control module
install the app
www.supla.org/android www.supla.org/ios
Light switch
Roller blind
Thermometer
230 V AC; IP20 Net weight: 0,046 kg
EN60669-1, EN 60669-2-1, ETSI EN 300 328,
ETSI EN 301 489-1, EN 301 489-17
Symbol for separate collection of waste electrical and
electronic equipment. Placing waste equipment with
other types of waste is prohibited.
ZAMELSp. z o.o. hereby declares that theSRW-
01 radio equipment type conforms to 2014/53/EU.
See the website below forthe full declaration of
conformity: www.zamel.com
Registered design © ZAMEL
Made inPoland
5 903669 222606
Garage door
https://cloud.supla.org/auth/create
Scan and open
to register an account
Wi-Fi
supla SRW-01
SRW-01 EN.indd 2-3 08.12.2017 12:29

SRW-01 - roller blind control module
TECHNICAL DATA
230 VAC
Rated supply voltage:
Relay contact parameters:
2 x NO 5 A / 250 V AC
Rated mains frequency:
50 / 60 Hz
Rated power consumption:
1.2 W
Transmission:
Wi-Fi 2.4 GHz 802.11 b/g/n
Operating range:
Wi-Fi range
Number of inputs:
2
Compatible connectors:
monostable (bell buttons), bistable (standard roller blind switches)
Number of output channels:
2
Relay contact parameters:
2 x NO 5 A / 250 V AC
Maximum output
2 x 5 A / 250 V AC: roller blind drives –350W
current-carryingcapacity:
Number ofconnection
6 (conductor cross-section up to 2.5 mm2)
terminals:
Enclosure mounting:
installation box Ø 60 mm
Operating temperature range:
-10 to +55°C
Enclosure protection rating:
IP20
Dimensions:
47.5 × 47.5 × 23 mm
Weight:
0.046 g
Reference standards:
EN 60669-1, EN60669-2-1, ETSIEN 300 328,
ETSI EN 301 489-1, EN 301 489-17
INSTALLATION CONSIDERATIONS:
1.Do not install receivers close to one another (if possible, maintain spacing of at least 15 cm between
individual receivers). In particular, avoid installing receivers on top of one another. It may result inWi-Fi
connectivity problems.
2. Observe the maximum output current-carrying capacity value:
•drives: 350 W –Class AC3
3.During installation, ensure the module is not subjected to direct water impact or operation in high
moisture content environments. The range of temperatures in the installation location should be from
-10 to +55°C.
4.SRW-01 modules are to be installed indoors. When installed outdoors, it must besecured in an
additional airtight installation box.
5.Installationconnectors for wired controlcan beconnected to inputs IN1 and IN2 of theSRW-01
receiver. The inputs operate with monostable or bistableconnectors. SRW-01 modules are to be
mountedin installation boxes. The enclosure dimensions facilitate installation in flush-mounted
(minimum Ø 60) and surface-mounted boxes. For flushmounting, “pocket boxes” are recommended.
6. After receiver installation, check its operation, ensuringthat the LEDis ON.
INSTALLATION
•SRW-01 modules are to be mounted in installation boxes. The enclosure dimensions facilitate
installation in flush-mounted (minimum Ø 60) and surface-mountedboxes. For flush mounting,
“pocket boxes” are recommended.
•Connect the device to single-phase mains, according to applicable standards. The device must be
installed, connected and adjusted by qualified electricians familiar with its operation manual and
functions. Due to safety reasons, do not install the device with its enclosure removed or damaged,
as it poses an electric shock risk.
SRW-01 EN.indd 4-5
install the app
Download the SUPLA app onyoursmartphone.
@
create an account / log in
If you already have a SUPLA account and are logged in the app, go to the next step.
If you donot have an account, click: “Create an account” in your app.
Enter youremail address and password in the form displayed.
Check your email inbox. Confirm registration by clicking the activation link sent in themessage.
Next, log inthe app using your email address.
connect to power
Connect the device to power using the diagram placed on its enclosure.
add a device
After logging in, select “Add a device” from the menu. The “Add a device” wizard is started. Take steps
according to messages displayed on the screen, until theset-up process is successfully completed.
Following successful set-up, the device connects with a Wi-Fi router. This is indicated by solid LED light.
You can also connect to the “ZAMEL-SRW-01…” Wi-Fi network. Enterthe following address: “192.168.4.1”
in your browser windowand provide your Wi-Fi data and email address used to register your account, and
press the “SAVE” button. The “Data saved” message confirms that access settings have been saved
successfully. Next, you must press the CONFIG button to store the settings.
control roller blinds
Control roller blinds remotely using SUPLA app onyour smartfon!
DETAILED OPERATION MANUAL AVAILABLE AT:
https://supla.zamel.pl/produkt/srw-01/
08.12.2017 12:29