ROW-01 - power socket and lights control module
Wi-Fi 2.4 GHz 802.11 b/g/n
monostable (bell buttons), bistable (standard light
Number of outputchannels:
switches without backlight function)
Relay contact parameters:
1 x NO 5 A / 250 V AC (potential-free NO contact)
Maximum output current-carrying capacity: 5A / 250 VAC: incandescent and halogen light bulbs –
Number of connection terminals:
CFL fluorescent lamps –250W; LED lamps –60W
6 (conductor cross-section up to 2.5 mm2)
Operating temperature range:
Enclosure protection rating:
EN 60669-1, EN 60669-2-1, ETSI EN 300 328, ETSI EN
INSTALLATION CONSIDERATIONS:
1.Do not install receivers close to one another (if possible, maintain spacing of at least 15 cm between
individual receivers). In particular, avoid installing receivers on top of one another. It may result inWi-Fi
connectivity problems.
2. Observe the maximum output current-carrying capacity value:
•incandescent and halogen light bulbs: 750W / per channel
•compact fluorescent lamps (CFL): 250W / perchannel
•LED lamps: 60W / perchannel
3.During installation, ensure the module is not subjected to direct water impact or operation in high
moisture content environments.
The range of temperatures in the installation location should be from -10 to +55°C.
4.ROW-01 modules are to be installed indoors. When installed outdoors, it must be secured in an
additional airtight installation box.
5.Installationconnectors for wired controlcan beconnected to inputs IN1 and IN2 of the ROW-01
receiver. The inputs operatewithmonostable or bistableconnectors. The default IN1 input operates
with a monostable (bell) mode, and IN2 operates in a bistable mode (standard light switches without
a backlight function).
6.After receiver installation, check its operation, ensuringthat the LED is ON.
INSTALLATION
•ROW-01modules are to be mounted in installation boxes. The enclosure dimensions facilitate
installation in flush-mounted (minimum Ø 60) and surface-mounted boxes. For flush mounting,
“pocket boxes” are recommended.
•Connect the device to single-phase mains, according to applicable standards. The device must be
installed, connected and adjusted by qualified electricians familiar with its operation manual and
functions. Due to safety reasons, do not install the device with its enclosure removed or damaged,
as it poses an electric shock risk.
ROW-01 EN.indd 4-5
install the app
Download the SUPLA app onyoursmartphone.
@
create an account / log in
If you already have a SUPLA account and are logged in the app, go to the next step.
If you donot have an account, click: “Create an account” in your app.
Enter youremail address and password in the form displayed.
Check your email inbox. Confirm registration byclicking the activation link sent in themessage.
Next, log inthe app using your email address.
connect to power
Connect the device to power using the diagram placed on its enclosure.
add a device
After logging in, select “Add a device” from the menu. The “Add a device” wizard is started. Take steps
according to messages displayed on the screen, until theset-up process is successfully completed.
Following successful set-up, the device connects with a Wi-Fi router. This is indicated by solid LED light.
You can also connect to the “ZAMEL-ROW-01…” Wi-Fi network. Enter the following address: “192.168.4.1”
in your browser window and provide your Wi-Fi data and email address used to register your account, and
press the “SAVE” button. The “Data saved” message confirms that access settings have been saved
successfully. Next, you must press the CONFIG button to store the settings.
control lights
Control lights and power sockets remotely using the SUPLA app on yoursmartphone!
DETAILED OPERATION MANUAL AVAILABLE AT:
https://supla.zamel.pl/produkt/row-01/
08.12.2017 12:29
