Zebex Z-3392BT User manual

Scanner Outline
Description Function
Scan Window Emits a red beam for barcode reading
LED Indicator Indicates the scanning status
Power Button/Scan Trigger Press and hold for 3 second until a long beep is
heard to turn power on or press to scan barcodes
Hand Strap Hole Used to attach hand straps
Battery Compartment Batteries are stored here
Micro USB slot Used for communication and charging
Package Contents
Items contain in the package may vary depending on the model of the scanner.
Wireless scanner with battery /
Scanner cradle (optional)
(with cradle)
(without cradle)
Li-ion battery pack
Communication cable for cradle
(optional)
Mini USB B to mini USB A cable
5V USB Power adapter
Cable clip
*Note: Actual product appearance may vary from the images on this page.
Charging the Device
Installing Battery
1. Unscrew the cap from the battery compartment at the
bottom of the scanner and insert the battery.
2. Make sure the red tag on the battery is tugged in
and not blocking the cable connector and close the cap.
3. Tighten the screw on the cap to secure the battery.
Connect the Cradle
Connect the Device with Cradle or USB cable
Approx. charging time: 4.5~6 hours
or
Micro USB
slot
LED
Indicator
Hand Strap
Hole
Battery
Compartment
Scan
Window
Power Button/
Scan Trigger
Communication cable
Mini USB B to USB power adaptor
only
Z-3392BT
Gun Type Wireless 2D Image Handheld Scanner

System Settings
Barcode Value Description
Return scanner to factory
defaults .
Return cradle host to factory
defaults
Return to USB default
(Communication cradle link
required)
Return to RS232 default
(Communication cradle link
required)
Return as USB-virtual COM port
default
Display firmware version
Scan Modes
Trigger mode
The scanner becomes inactive as soon as
the data is transmitted. It must be
triggered to become active again.
Auto scan mode
The scanner is still active after the data is
transmitted but the successive
transmission of the same barcode is not
allowed when the trigger switch is
pressed again.
Presentation mode
Also called auto trigger mode. The
scanner is inactive but will automatically
detect barcodes presented in the scan
zone and become active.
USB Online Mode
USB online mode
The scanner connects directly to a USB
host to recharge and transmit data.
Beeper Settings
Good Read Beeper Tone Selection
Medium beeper tone
High beeper tone
Low beeper tone
Speaker disable
Radio Communication
BT HID mode
BT HID mode (Combo
keyboard)
For Apple mode
(Enter PIN CODE then scan SET)
Multi Media Keyboard ( For
Apple Mode)
Software Keyboard
ON/OFF( For Apple Mode)
SET

FCC Statement:
This device complies with Part 15 of the FCC rules standard. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operating in conjunction with
any other antenna or transmitter.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
Referring to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be
operated simultaneously without C2PC.
