Zebex Z-8082 Lite User manual

2D Image On-Counter Scanner

2D Image On-Counter Scanner
i
USER’S MANUAL
This User’s Manual is intended for:
⚫2D Image On-Counter Scanner: Z-8082 Lite
Revision History
Changes to the original manual are listed below:
Version
Date
Description of Version
1.0.0
2019/1/2
Initial Release

2D Image On-Counter Scanner
ii
USER’S MANUAL
Important Notice
No warranty of any kind is made in regard to this material, including, but not limited to, implied
warranties of merchantability or fitness for a particular purpose. We are not liable for any errors
contained herein or incidental or consequential damages in connection with furnishing,
performance or use of this material.
No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed,
or translated into any language or computer language in any form or by any means electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without express written consent
and authorization.
We reserve the right to make changes in product design without reservation and without
notification. The material in this guide is for information only and is subject to change without
notice.
All trademarks mentioned herein, registered or otherwise, are the properties of their various
respective owners.
Copyright © 2018. All rights reserved.
Guidance for Printing
This manual is in A5 size. Please double check your printer setting before printing it out.
Adjustments: Do not attempt any adjustments or alteration of this product. Do not
remove the protective housing of the scanner. There are no user-serviceable parts inside.
Optical: The use of optical instruments with this product will increase the eye hazard.
Optical instruments include binoculars, magnifying glasses, and microscopes but do not
include normal eye glasses worn by the user.
CAUTION: Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
For CE-countries
This scanner is in conformity with CE standards. Please note that an approved, CE-marked power
supply unit should be used in order to maintain CE conformance.

2D Image On-Counter Scanner
iii
USER’S MANUAL
Table of Contents
Introduction .........................................................................................................................1
Package Contents.................................................................................................................2
Product Overview.................................................................................................................3
Beeper Indication.................................................................................................................4
LED Indication ......................................................................................................................4
Installation ...........................................................................................................................5
Scan Test...............................................................................................................................7
Setting Up the Scanner.........................................................................................................8
Programming the Scanner ...................................................................................................8
Standby Mode of Scanner....................................................................................................9
USB Virtual COM Installation .............................................................................................10
Dimensions.........................................................................................................................12
Scan Angle..........................................................................................................................12
Mounting Screw Holes .......................................................................................................13
Interface Cable Pin Out ......................................................................................................14
Specification.......................................................................................................................15
Cleaning the Scan Window ................................................................................................16
Trouble Shooting................................................................................................................16

2D Image On-Counter Scanner
1
USER’S MANUAL
Introduction
Z-8082 Lite on-counter scanner is the new lightweight version of Z-8082. It includes all
the core features as well as salient attributes of Z-8082 like 2D scanning, full motion
tolerance, and wide scan zone. The instant decoding performance provides efficiency for
your 1D and 2D consumer applications. Z-8082 Lite is designed to address today’s
business needs allowing users to capture data accurately and effectively with minimum
complexity.
• High speed and reliable performance on all common 1D and 2D codes
• Offer convenience by its full-directional motion tolerance function and wide scan zone
• VESA 100 compatible to satisfied your mounting demands

2D Image On-Counter Scanner
2
2
USER’S MANUAL
Package Contents
2D Image On-Counter Scanner with
Table Mount
Interface Cable - USB or RS-232 (Type
depends on customer selection.)
or
5V Power Adapter (Only for RS-232
cable as optional accessory. Plug type
depends on electrical requirements
of your geographic location.)
Screw Pack
Quick Guide
1. Please leave this user’s manual within easy access for persons
using the scanner.
2. If any contents are damaged or missing, please contact your
dealer immediately.

2D Image On-Counter Scanner
3
USER’S MANUAL
Product Overview
#
Description
Function
1
Volume Button
Push to switch beep volume
2
LED Indicator
Reading status indication
3
Tone Button
Push to switch beep tone
4
Scan Window
Read barcodes
5
Speaker Exit
For beep tone indication
6
Table Mount
For securing the scanner on the table
7
Host Port
Plug the interface cable into this port
Do not let the scan LED light face directly to human eyes.
1
3
4
5
2
6
7

2D Image On-Counter Scanner
4
2
USER’S MANUAL
Beeper Indication
Beeps
Indication
3 beeps in a series from low to high pitch
Power up
1 short beep
A barcode has been successfully decoded
2 short beeps
The scanner has entered program mode
1 long beep
A setting has been programmed
3 beeps in a series from low to high pitch
The scanner has exited program mode
3 short beeps
Error setting the scanner
LED Indication
LED
Indication
1 red flash
A barcode has been successfully decoded
Steady blue
Scanner in work mode

2D Image On-Counter Scanner
5
USER’S MANUAL
Installation
1. Separate Table Mount from the scanner.
2. Attach the Interface Cable by inserting it through the hole on table mount as
illustrated.
3. Secure the table mount to counter by using three (M3) self tapping screws and
washers.

2D Image On-Counter Scanner
6
2
USER’S MANUAL
4. Plug the cable into the Host Port, then attach the scanner with the table mount.
5. Tightly secure the scanner and table mount with two (M3) mechine screws.
6. Connect the cable to the terminal’s communication port. Plug the power supply
into the power jack on the interface cable if host can not provide sufficient power.
Use only an AC/DC power adapter approved for the scanner. Use of other
power supplies may cause damage to the scanner, and void the factory
warranty.

2D Image On-Counter Scanner
7
USER’S MANUAL
Scan Test
1. With the scanner running (blue LED lights) and the host system on, try to scan
several known-good barcodes.
2. Check the results on the POS screen. If the scanner is reading okay, it is likely that
no further setup is necessary.
3. If the POS screen does not show the expected scans, please refer to the
Programming Guide.
1. If the scanner is connected to a USB for this test, it should read one
barcode, beep and then remain a red LED indicating light. This is
normal when the USB is not connected to a live host terminal.
2. If the scanner does not produce any beeps, or produces the wrong
beeps, or the LED does not light up, remove the power connection
and refer to the Troubleshooting section.

2D Image On-Counter Scanner
8
2
USER’S MANUAL
Setting Up the Scanner
In certain cases no setup is required. The scanner is either pre-programmed to suit the
situation, or it automatically detects and is ready to go. In other cases the scanner must
be informed about what kind of system it is connected to. This can be done in a few
moments using the programming barcodes in the Programming Guide.
The Programming Guide may be used to set a number of parameters on the scanner:
communication interface type (RS-232, USB), beep tone, scan mode, baud rate,
enable/disable decoding of numerous code types, and more advanced settings like set
prefix and suffix.
Individual parameters may be set at any time without affecting the other parameters.
Programming the Scanner
1. When the scanner is powered on (blue LED lights), find the Set barcode in the
Quick Start Guide or Programming Guide and present this barcode to the scanner.
When the scanner gives two beeps, it means the scanner is in programming mode.
2. Decide which parameters are required and find their barcodes in the Quick Start
Guide or Programming Guide.
3. Cover unwanted codes with your hand and present the desired codes, one by one,
to the scanner; the scanner beeps once as it accepts each code.
4. When done, again present the End barcode to the scanner. The scanner beeps
thrice, it means the scanner is out of programming mode. The scanner has been
programmed.
5. Test again with known-good barcodes. If results are good, you are done setting up.
Otherwise, return to step 1 and try again.

2D Image On-Counter Scanner
9
USER’S MANUAL
Standby Mode of Scanner
After the scanner has been inactive for a period of time, the scanner would enter the
sleep mode by setting Standby Time. The time period of continue scan mode is
programmable.
To wake up the scanner, present an object close to the scan window.
Standby Time Programming Parameters
Set
Off (Default)
5 Seconds
10 Seconds
20 Seconds
30 Seconds
60 Seconds
End
The scanner includes a sensor that detects activity in front of the scan window.
The detecting distance is about 5 cm (1.9 inch) from the scan window while in
condition with effectiveness of environment lights.

2D Image On-Counter Scanner
10
2
USER’S MANUAL
USB Virtual COM Installation
If you use virtual COM port emulation, follow the steps below to start using the scanner.
1. Execute the driver (VCOM-Driver-Installation.exe).
2. Connect the scanner USB cable to the host computer.
3. Set the interface to USB Virtual COM Port.
Set
Enable USB virtual COM
End

2D Image On-Counter Scanner
11
USER’S MANUAL
On the computer, check Device Manager to see if the computer successfully detects the
scanner as “Barcode Scanner USB-COM device.” (The COM port number would vary
depending on different hardware environment).

2D Image On-Counter Scanner
12
2
USER’S MANUAL
Dimensions
Unit: mm
Scan Angle

2D Image On-Counter Scanner
13
USER’S MANUAL
Mounting Screw Holes
The device is reserved with several mounting holes for permanent fixture if required.
Please refer to the figure below for detailed information.
Unit: mm

2D Image On-Counter Scanner
14
2
USER’S MANUAL
Interface Cable Pin Out
RS-232C Cable - DTE pin out (Power adapter required if host can not provide sufficient
power)
PIN-OUT
CONFIGURATION
DB-9 (F)
FUNCTION
2
TX
3
RX
5
GND
7
CTS
8
RTS
USB Cable - USB Type A
Connector
Function
1.
VCC
2.
D-
3.
D+
4.
VSS