Zenitel Turbine Compact IP + Guide

Turbine Compact IP +
TCIS-1+
TCIS-2+
TCIS-3+
TCIS-4+
TCIS-5+
TCIS-6+
zenitel.com
EN
A100K12158
MOUNTING MANUAL

2
Item Number Type Item Name
1008311010 TCIS-1+ Turbine Compact IP - thermoplastic front plate
1008311020 TCIS-2+ Turbine Compact IP - stainless steel front plate
1008311030 TCIS-3+ Turbine Compact IP - thermoplastic front plate
1008311040 TCIS-4+ Turbine Compact IP - thermoplastic front plate with PMOLED display
100831050 TCIS-5+ Turbine Compact IP - thermoplastic front plate with PMOLED display
1008311060 TCIS-6+ Turbine Compact IP - thermoplastic front plate with PMOLED display
1008140010 TA-1 Turbine On-Wall Back Box
1008140020 TA-2 Turbine Flush Mount 2-Gang Double-Depth Back Box
1008140050 TA-5 Turbine Bracket for Flush Mount Back Box
Turbine Compact IP + Stations
This document describes the dimensions, mounting procedure, and connections of the Turbine
Compact IP Stations. Zenitel takes no responsibility for damages caused by improper or inadequate
mounting. The Turbine Compact IP product range comprises the following stations & accessories:
TCIS-1+ TCIS-2+ TCIS-3+ TCIS-4+ TCIS-5+ TCIS-6+
Turbine Compact IP + Stations
120 mm
180 mm
23.849 mm

3
On-Wall Surface Mounting
Back Box - TA-1
The IP-66 rating is only valid when TA-1 Back Box is used.
76 mm
150 mm
D
6.5 mm
25 mm
120 mm
Mounting Hole
Mounting Hole
Cable Holes
M20 M16
Mounting Hole
• Mounting holes are to be drilled as
shown.
• Max. recommended screw diameter:
ISO M6 or ANSI 1/4”.
• Screw length must be greater than
25 mm or 1”.
• A4 stainless steel socket head
screws/bolts are recommended.
• Max. recommended screw head
diameter: 9.5 mm or 3/8”.
Included:
4x M5 fasteners
2x Grommets
1x M20 Cable Gland
4x Washers for extra protection against
corrosive eects between surfaces. To
be placed at bottom of the 4 mounting
holes.
On-Wall Surface Mounting Procedure
Surface
Mount
Back Box
Gasket
1
2
M
icrophone
Washers
Turbine
Station
3
The gasket MUST be mounted to seal
the station!
Ensure the station is mounted
vertically with the microphone facing
down.
Ensure there is enough clearance un-
der the station so that the microphone
is NOT smothered.
Place the washers at the bottom of the
4 mounting holes on the back box.
Use the grommets and M20 cable
gland for the cable holes on the back
box.
1. Mount the back box onto the wall using A4 socked head screws.
2. Fit the gasket onto the back box with the ridged side facing down. Then plug the Ethernet cable
into the RJ-45 port on the station.
3. Mount the Turbine station onto the back box with the M5 fasteners, applying 1.5 Nm torque.

4
Flush Mounting
2-Gang Double-Depth Back Box - TA-2
It is recommended to utilize back boxes with weep holes at the back.
96 mm
48 mm
25 mm
23 mm
89 mm
89 mm
46 mm
96 mm
SIDE
SIDE
22 mm
Flush Mount Bracket - TA-5
The TA-5 Bracket or other customized solution is required for flush mounting.
83 mm
87 mm
46 mm
50 mm
4 mm
4 mm
74 mm
91 mm
CUTOUT
• Fits US 2-gang electrical boxes.
• Recommended screw diameter: up to M4
(5/32”). Use #6-32 UNC pan head screws for
the TA-2 back box.
Included:
4x M5 Fasteners
4x #6-32 UNC Pan Head Screws

5
Flush Mounting Procedure
The gasket MUST be mounted to seal
the station!
Ensure the station is mounted
vertically with the microphone facing
down.
Ensure there is enough clearance un-
der the station so that the microphone
is NOT smothered.
Apply silicone sealant all around the
aluminium frame of the station. Make
sure to leave the microphone aperture
open.
1
2-Gang
Back Box
Microphone
Bracket
2
Gasket
3
4
Turbine
Station
1. Mount the 2-gang back box into the wall.
2. Mount the bracket onto the back box with #6-32UNC pan head screws.
3. Fit the gasket onto the bracket with the ridged side facing down. Then plug the Ethernet cable into
the RJ-45 port on the station.
4. Mount the Turbine station onto the bracket with the M5 fasteners.
Connections
The Turbine Compact IP + station has a RJ-45 PoE/LAN port, and 6-pin & 10-pin external connectors.
Use cables crimped with ferrules for terminal block connectors.
Ethernet/
Power
10/100 Mps Ethernet RJ-45 port for
LAN (uplink) connection. Supports
PoE (802.3af). Draws from either
spare line or signal line.
Secondary
Power
24V DC (16-48 V) secondary power
is provided from an external adapter.
Relays
There is one Double Throw relay
contact with 6W switching power.
COM, NO, NC contacts are provided.
Max: 250V AC/220V DC, 2A, 60W.
Input/Output
6 I/Os are available. Each I/O can be
configured as either input, output or
LED driver.
Audio Line Out A balanced 600 ohm audio line with
induction loop signal.
• When the Turbine Station is connected to the network, its IP address is automatically
obtained from a DHCP server or an IP adress in the range 169.254.xx will be assigned.
• To make the station speak its IP address, press the call button on the station.

A100K12158
DOC NO.
zenitel.com [e-mail]
Zenitel and its subsidiaries assume no responsibility for any errors that may appear in this publication, or for damages arising from the information therein. Zenitel products are developed and marketed by
Zenitel. The company’s Quality Assurance System is certified to meet the requirements in NS-EN ISO 9001. Zenitel reserves the right to modify designs and alter specifications without notice. ZENITEL
PROPRIETARY. This document and its supplementing elements contain Zenitel or third-party information which is proprietary and confidential. Any disclosure, copying, distribution or use is prohibited, if not
otherwise explicitly agreed in writing with Zenitel. Any authorized reproduction, in part or in whole, must include this legend: Zenitel – All rights reserved.
24.08.2022
Hear, be heard and be understood, every time.
Intelligent communication
The WEEE Directive does not legislate that Zenitel, as a ‘producer’, shall collect ‘end of life’
WEEE.This ‘end of life’ WEEE should be recycled appropriately by the owner who should
use proper treatment and recycling measures. It should not be disposed to landfill.
Many electrical items that we throw away can be repaired or recycled. Recycling items helps to save our
natural finite resources and also reduces the environmental and health risks associated with sending
electrical goods to landfill.
Under the WEEE Regulations, all new electrical goods should now be marked with the
crossed-out wheeled bin symbol shown.
Goods are marked with this symbol to show that they were produced after 13th August
2005, and should be disposed of separately from normal household waste so that they
can be recycled.