Zenitel VR3G-1 Guide

EN
A100K12226
v1.3
VR3G-1
VR3G-1P
Mounting & Installation Manual
Vandal Resistant IP and SIP Intercom

2 33
This document serves as a mounting and installation guide for the
VR3G-1 and VR3G-1P Vandal Restistant IP and SIP Intercom Stations.
For more information and instructions on configuration of the VR3G-1
and VR3G-1P go to wiki.zenitel.com/wiki/Main_Page.
The Vandal Resistant series consists of the following components:
About
Item Number Item Name Description
1008021010 VR3G-1 Vandal resistant 3 gang 1 button IP
and SIP Intercom
1008021015 VR3G-1P Vandal resistant 3 gang 1 button
(piezo) IP and SIP intercom
1008098300 3 Gang Flush Mount back box
Safety information
This manual contains important instructions that must be followed. These
instructions are intended to ensure that the product is mounted and
installed correctly to avoid equipment damage or property loss.
A note symbol indicates that extra care must be taken. Damage
to equipment can occur, or it may not function as intended.
Please read all warnings before installing this product.
The station should be installed by a competent person in accordance
with national and local regulations. Zenitel takes no responsibility for
damages caused by improper or inadequate installation.
Description
VR3G-1
Item Description
1Speaker
2Call Button
3Piezo Call Button
4Microphone
5LED
VR3G-1P
CALL CALL
1
2 3
45

4 55
+24
COM
NO NC
+5
1
2
3
4
5
6
+
-
+24
COM
NO
NC
+5
1
2
3
4
5
6
+
-
Item Description Comment
1CPU Module
2Tamper Switch Connected to input #4
3Relay
Double Throw relay contact with 60W
switching power. COM, NO, NC contacts are
provided. Max: 250VAC/220VDC, 2A, 60W.
4I/O interface
6 general purpose I/Os. Each I/O can be
configured either as an input or 12mA LED
driver output
5Line Output Balanced 600 ohm audio line out. Suitable
for e.g. external induction loop amplifier
6Power Input Optional 24VDC power input from external
power supply
7LAN Port 10/100/1000Mbps RJ-45 port connecting
to Ethernet. PoE/PoE+ is supported.
543
1
2
6
7
Installation
VR3G-1/VR3G-1P can be powered by PoE. This is done by connecting
an Ethernet cable to the LAN port of the station and a PoE switch.
NB! If PoE is used, the station must be installed using a
shielded Ethernet cable with grounding at the switch end.
If the switch does not support PoE, a 24VDC power supply can be
connected to the stations Power Input.
If an external power supply is being used, please make sure
the power supply matches the station.
Mounting
Mounting considerations
Check the specification of the product for the installation environment.
To achieve the vandal resistanse the stations are designed
for, the intercoms must be flush mounted.
To ensure the IP66 rating and that nothing can penetrate
behind the edge of the intercom, it must be mounted on a
surface that is completely planar.

6 77
Insert and secure the 3 Gang Flush Mount back box into
designated slot in the wall. Make sure that the box is squarely
mounted and the front surface flush with the wall surface.
Plug the Ethernet cable into LAN port on the station. If the
switch does not support PoE, a 24VDC Power Supply can be
connected to the stations Power Input.
Mount the Vandal Resistant Station onto the back box with the
6-32 UNC X ¾ fasteners provided. Apply 1.5 Nm / 1.1 lb-ft torque.
1
2
3
Flush mounting
When flush mounting vandal restistant station, use the 3 Gang Flush
Mount back box.
48
1
2
3
• Ready one of the prepunched holes in the backbox for power and
network wiring.
• Have the necessary cables ready before starting the mounting
procedure.
Make sure the Tamper Switch is properly connected to the
back end of the back box.
Retighten the screws after mounting, as the gasket behind
the front plate will get compressed.
all dimensions in mm

8 99
Technical specifications Value
Weight 0.74 kg
Dimensions (HxWxD) 160 x 114 x 60mm
IP Rating IP66
IK Rating IK10
Relative humidity < 95% not condensing
Operating temperature range VR3G-1: -40° to 70° C / -40° to 158 ° F
VR3G-1P: -20° to 75° C / -4° to 167 ° F
Encapsulation material A4 Steel
Power Options PoE, PoE+, 24VDC PSU
PoE (power over Ethernet) IEEE 802.3af standard
Power consumption Idle 1.8W, max 12W (depending on
volume)
Get started
When the Vandal Resistant Station is connected to the network, its IP
address is automatically obtained from a DHCP server or an IP adress in
the range 169.254.xx will be assigned.
To make the station speak its IP address, press the Call Button on the
station.
The Vandal Resistant Station can operate in three dierent modes,
ICX-AlphaCom, Edge and SIP, depending on what kind of server it is
registered to. Enter the link or scan the QR-code below to go to Zenitel
Wiki for configuration instructions.
Zenitel Wiki: wiki.zenitel.com/wiki/Main_Page.
Specifications
Contact Information
Visit zenitel.com to find your country’s contact information.

10
The WEEE Directive does not legislate that Zenitel, as a ‘producer’,
shall collect ‘end of life’ WEEE.
This ‘end of life’ WEEE should be recycled appropriately by the owner
who should use proper treatment and recycling measures. It should
not be disposed to landfill.
Many electrical items that we throw away can be repaired
or recycled. Recycling items helps to save our natural finite
resources and also reduces the environmental and health risks
associated with sending electrical goods to landfill.
Under the WEEE Regulations, all new electrical goods should
now be marked with the crossed-out wheeled bin symbol
shown.
Goods are marked with this symbol to show that they were
produced after 13th August 2005, and should be disposed of
separately from normal household waste so that they can be
recycled.

DOC. NO.
Zenitel and its subsidiaries assume no responsibility for any errors that may appear in this publication, or for damages arising
from the information therein. Zenitel, Vingtor-Stentofon and Phontech products are developed and marketed by Zenitel. The
company’s Quality Assurance System is certified to meet the requirements in NS-EN ISO 9001. Zenitel reserves the right to
modify designs and alter specifications without notice. ZENITEL PROPRIETARY. This document and its supplementing elements
contain Zenitel or third-party information which is proprietary and confidential. Any disclosure, copying, distribution or use is
prohibited, if not otherwise explicitly agreed in writing with Zenitel. Any authorized reproduction, in part or in whole, must include
this legend: Zenitel – All rights reserved.
[e-mail]100K12226v1.3