Zennio DALIBOX ZDI-DLB4 Guide

© Zennio Avance y Tecnología S.L. Edition 1 Further information www.zennio.com Page. 1/ 2
DALIBOX Broadcast 4CH
KNX-DALI Broadcast Interface for up to 4 channels
ZDI-DLB4 Technical Documentation
FEATURES
Control of up to 20 DALI ballasts per channel in up to 4 channels.
Ballast replacement allowed with automatic detection.
Error detection and monitoring (except multiaddress DALI ballasts).
Burn-in, Stand-by and Auto-off functionality for each channel.
Not suitable for emergency lighting control.
Manual control through buttons and status LED indicators.
110/230V 50/60Hz external power supply required.
Total data saving on power failure.
KNX BCU integrated.
Size 67 x 90 x 80mm (4,5 DIN units).
DIN rail unit assembly (EN 50022), with snap fit clamp.
DALI Standard compatible.
CE directives compliant.
Programming/test button: short button press to set programming mode. If this button is held while plugging the device into the KNX bus, it goes into
safe mode.
Programming/Test LED: programming mode indicator (red). When the device goes into safe mode, it blinks (red) every half second. The test mode is
indicated by the green color. During start up (after reset or power failure) and if the device is not in safe mode, LEDs indicator blinks red once.
1. DALI channel output 2. External supply 3. DALI channel control button 4. DALI channel status LED
5. Programming/Test button 6. External supply LED 7. Programming/Test LED 8. KNX connector
Figure 1. DALIBOX Broadcast 4CH
GENERAL SYSTEM SPECIFICATIONS
CONCEPT
DESCRIPTION
Type of device Electric operation control device
KNX supply
Voltage (typical) 29VDC SELV
Voltage range 21…31VDC
Maximum
consumption
Voltage mA mW
29VDC (typical) 7 203
24VDC(1) 10 240
Bus connection Typical bus connector TP1; 0,80mm² section
Ext. power
supply Voltage and frequency 110/230VAC 50/60Hz
Maximum consumption 150mA
Ambient temperature from 0ºC to +45ºC
Storage temperature from -20ºC to +55ºC
Ambient humidity 5 to 95% RH (no condensation)
Storage humidity (relative) 5 to 95% RH (no condensation)
Complementary characteristics Class B
Safety class II
Operation type Continuous operation
Device action type Type 1
Electrical solicitations period Long
Type of protection IP20, clean environment
Assembly Independent control assembly device to be mounted inside of electrical panels with
DIN rail (EN 50022).
Minimal clearances Not required
KNX bus failure response Data saving according to parameterization.
Response when restarting KNX bus Data recovering change according to parameterization.
Operation indication Programming LED indicates programming mode (red) and test mode (green). Each DALI channel LED indicates its status (flashing = error, see Fig. 2; fixed = active
output). Power supply LED indicates the presence of supply voltage.
Weight 124g
PCB CTI index 175V
Enclosure PC FR V0 halogen free
(1)
Maximum consumption in the worst
case
scenario (KNX Fan
-
In model)
1
8
5
7
1
2
6
4
3

© Zennio Avance y Tecnología S.L. Edition 1 Further information www.zennio.com Page. 2/ 2
SA
FETY INSTRUCTIONS
Installation should only be performed by qualified electricians following applicable regulations on preventing accidents, as
required by law.
The installation must be equipped with a device assuring the omni-polar sectioning. A 10A circuit breaker is recommended.
Do not connect Main Voltage (110/230VAC) or any other external voltages to any point of the KNX or DALI system.
Connecting an external voltage might put the entire KNX system at risk.
Make sure during the installation that there is always sufficient insulation between the main voltage 110/230VAC and the KNX
or DALI bus or the extension inputs.
Once the device is installed, it must not be accessible from the outside.
Keep away from water and do not cover the device with clothes, paper or any other material when in use.
The device has a short-circuit protection fuse that, in case of activation, it should not be rearmed or replaced except for our
technical department.
The WEEE logo means that this device contains electronic parts and it must be discarded properly following the instructions
of http://zennio.com/weee-regulation.
CONNECTION SCHEMATIC
Removing DALIBOX Broadcast 4CH from DIN rail:
Attaching
DALIBOX Broadcast 4
CH
to DIN rail:
OUTPUT SPECIFICATIONS AND CONNECTIONS OF DALI CHANNELS
CONCEPT DESCRIPTION
Number of channels 4
Channel type DALI bus
Channel voltage 16VDC SELV
Maximum current per output 40mA
Maximum DALI ballasts per channel(2) 20
Maximum length of cable 300m (considering 1,5mm
2
)
Short-circuit protection YES
Overload protection YES
Over-voltage protection YES
Connection method Cable screw terminal
Cable cross-section 0,5mm² to 2,5mm² (26-12 AWG)
(2) One DALI address is considered per DALI ballast.
INPUT SPECIFICATIONS AND CONNECTIONS OF EXTERNAL POWER SUPPLY
CONCEPT DESCRIPTION
Fuse protection of
supply to DALI power
source
Voltage 250V
Current 4A
Response type F (Fast acting)
Connection method Cable screw terminal
Cable cross-section 0,2mm² to 4mm² (26-10 AWG)
Figure 2.
Error notification through
DALI channel status LED
Ballast
1.1 Ballast
1.n
(n≤20)
110/230 V~
50/60 Hz
Ballast
4.1 Ballast
4.n
(n≤20)
Note
: Electrical connection
between different DALI
channels must be avoided.
Short-circuit Open circuit Ballast failure Lampfailure Overload
Time(s)
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Description:
LEDOn LEDOff
Time(s)