ZiLOG Z8 Encore! XP User manual

Copyright ©2011 Zilog®, Inc. All rights reserved.
www.zilog.com
Introduction
This Quick Start Guide describes how to set up Zilog’s Z8 Encore! XP®F64XX Series
Development Kit and begin using it to build your designs and applications.
This document discusses the following elements:
• Kit Contents
• System Requirements
• Configuring the Power Supply
• Installation Overview
• Getting Started Using ZDSII
Kit Contents
Hardware
Hardware requirements include:
• Z8 Encore! XP F64XX Series Flash Microcontrollers Development Board
• USB Smart Cable for connecting a PC to Z8 Encore! XP Development Board
• Universal power supply
Software (On CD-ROM)
Software requirements include:
• Zilog Developer Studio (ZDS) II for Z8 Encore! IDE with ANSI C-Compiler
• Sample code
• Acrobat Reader
• Document browser
Related Documentation
Z8 Encore! XP technical documentation on CD-ROM includes:
• Development Kit User Manual
• ZDSII – IDE User Manual
Z8 Encore! XP®F64XX Series
Development Kit
Quick Start Guide QS002810-0111
Z8 Encore! XP®Product Family

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 2 of 12
• eZ8™ CPU User Manual
• Product Specification
•ProductBrief
System Requirements
Table 1 lists the system requirements for running ZDSII.
Configuring the Power Supply
The universal power supply kit features four different plug adapters in one box and the
power supply itself in another. The power supply ships with a slide-out plate which must
be removed to insert the location-specific plug adapter.
Observe the following steps to install a location-specific adapter plug:
1. Remove the slide-out plate.
2. Select the appropriate AC plug adapter and insert it into the slot that remains after re-
moving the slide-out plate.
3. Slide the new plug adapter into the slot until it snaps into place.
Table 1. ZDSII System Requirements
Recommended Configuration Minimum Configuration
• Windows XP Professional SP3 or later
• Pentium IV 2.2GHz processor or Higher
• 1024MB RAM or Higher
• 135 MB hard disk space (includes
Application and Documentation)
• Super VGA Video Adapter
• CD-ROM for installation
• USB High-Speed port (when using USB
Smart Cable)
• Ethernet port (when using Ethernet
Smart Cable)
• RS232 communication port with
hardware flow control
• Internet browser (Internet Explorer or
Netscape)
• Windows XP Professional
• Pentium IV 1.2GHZ processor
• 512 MB RAM
• 50 MB hard disk space (only includes
Application)
• Super VGA Video Adapter
• CD-ROM for installation
• USB Full-Speed port (when using USB
Smart Cable)
• RS232 communication port with
hardware flow control
• Internet browser (Internet Explorer or
Netscape)

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 3 of 12
For convenience, you can leave the adapter slot cover in place and plug in a standard com-
puter equipment AC power cord (purchased separately) between the AC cord receptacle
on the end of the power supply and an electrical outlet.
Previous versions of the development kit used the Serial Smart Cable.
New kits developed from June 2006 uses the USB Smart Cable. Refer to
the following instructions for specifications on installing the cable avail-
able with your kit.
Always use a grounding strap to prevent damage resulting from electro-
static discharge (ESD).
Installation Overview
Observe the following steps to set up your Z8 Encore! XP®F64XX Series Development
Kit hardware and software:
1. Install the ZDSII software as described in the Installing ZDSII – Z8 Encore! Software
section on page 4.
2. For initial setup, ensure jumper J4 (DIS IRDA) is IN (shunt installed).
For detailed
jumper descriptions,
refer to the Z8 Encore! XP F64XX Series Development Kit User
Manual (UM0151).
3. Connect your PC to the Z8 Encore! XP development board as noted below:
–If your kit is supplied with the USB Smart Cable, follow the instructions in the
Installing the USB Smart Cable section on page 4.
–If your kit is supplied with the Serial Smart Cable, follow the instructions in the
Connecting the Serial Smart Cable to your Development Board section on page 7.
4. After connecting the development board to your PC, run the suppliedsample project as
described in the Getting Started Using ZDSII section on page 8.
5. To configure the power supply, follow the steps provided in the Configuring the Power
Supply section on page 2.
Note:
Caution:

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 4 of 12
For information about developing an application using the Z8FMC16100 Series of Motor
Control products, refer to the Zilog Developer Studio II – Z8 Encore! User Manual
(UM0130) and/or the Z8 Encore! XP F64XX Series Development Kit User Manual
(UM0151).
Installing ZDSII – Z8 Encore! Software
Observe the following steps to install the ZDSII Z8 Encore!®software:
1. Insert the Zilog Developer Studio II CD into the CD-ROM drive. DemoShield launches
automatically. If DemoShield does not launch automatically, open the Windows Ex-
plorer, browse to your CD-ROM drive and double-click launch.exe to launch the in-
staller.
2. Click the Install Products button on the main installer menu.
3. From the product installer list, you can choose to install ZDSII for both ZDSII and as-
sociated documentation. You can also copy the documentation directly from the CD-
ROM to your hard disk using Windows Explorer, or read the documentation directly
from the CD-ROM.
Installing the USB Smart Cable
The USB Smart Cable installation procedure differs based on the type of Windows operat-
ing system on which you will run ZDSII. This section describes how to install the USB
Smart Cable and associated driver software for your particular Windows OS.
32- and 64-Bit Windows 7
Observe the following steps to install the USB Smart Cable and associated driver software
for Windows 7 systems.
a. Connect the USB Smart Cable to the host PC. The Found New Hardware dialog
box is displayed.
b. Select Locate and install driver software (recommended). The User Account
Control window is displayed; click Continue. The Driver Software Installation
window is displayed, followed by the Found New Hardware–USB Smart Cable
dialog box.
c. Select I don't have the disc. Show me other options.
d. Select Browse my computer for driver software (advanced).

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 5 of 12
e. Browse to one of the following driver directories based on the Win 7 OS you use.
• For 32-bit Windows 7 systems:
– <ZDS II Installation Directory>\device drivers\USB\x32
– <ZDS II Installation CD>\device drivers\USB\x32
• For 64-bit Windows 7 systems:
– <ZDS II Installation Directory>\device drivers\USB\x64
– <ZDS II Installation CD>\device drivers\USB\x64
f. Click Next.The Windows Security dialog box is displayed.
g. Select Install this driver software anyway.
h. When the software has been installed successfully, click Close.
32- and 64-Bit Windows Vista
Observe the following steps to install the USB Smart Cable and associated driver software
for Windows Vista systems.
a. Connect the USB Smart Cable to the host PC. The Found New Hardware dialog
box is displayed.
b. Select Locate and install driver software (recommended). The User Account
Control window is displayed; click Continue. The Driver Software Installation
window is displayed, followed by the Found New Hardware–USB Smart Cable
dialog box.
c. Select I don't have the disc. Show me other options.
d. Select Browse my computer for driver software (advanced).
e. Browse to one of the following driver directories based on the Vista OS you use.
• For 32-bit Vista systems:
–<ZDS II Installation Directory>\?evice drivers\USB\x32
– <ZDS II Installation CD>\device drivers\USB\x32
• For 64-bit Vista systems:
– <ZDS II Installation Directory>\device drivers\USB\x64
– <ZDS II Installation CD>\device drivers\USB\x64
f. Click Next.The Windows Security dialog box is displayed.
g. Select Install this driver software anyway.
h. When the software has been installed successfully, click Close.

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 6 of 12
Windows XP
Observe the following steps to install the USB Smart Cable for Windows XP.
1. Connect the Zilog USB device to the Host PC. The Found New Hardware Wizard
should activate automatically after connecting the Zilog USB device for the first time;
Select No, not at this time if asked to connect to Windows®Update.
2. Select Install from a list or specific location (Advanced) and click Next.
If the Windows Logo testing dialog appears, select Continue Anyway.
3. Select Search for the best driver in these locations and Include this location in
search:.
4. Browse to the following directory and click Next:
<ZDS installation>\device drivers\USB\x32
5. Find the appropriate driver, and click Next.
6. Click Finish to complete the installation.
Windows 2000
Observe the following steps to install the USB Smart Cable for Windows 2000.
1. Connect the Zilog USB device to the Host PC. The Found New Hardware Wizard
should activate automatically after connecting the Zilog USB device for the first time.
2. Click Next in the Found New Hardware Wizard after it has been activated.
3. Select Search for a suitable driver for my device (Recommended) and click Next.
4. Select Specify a location and click Next.
5. Browse to the following directory and click OK:
<ZDS installation>\device drivers\USB\x32
6. Find the appropriate driver, and click Next.
7. Click Finish to complete the installation.
Note:

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 7 of 12
Connecting the USB Smart Cable to the
Development Board
Observe the following steps to connect the USB Smart Cable to the Development Board.
The power to the development board must be disconnected or turned off
before connecting or disconnecting the USB Smart Cable.
1. Attach one end of the six-conductor ribbon cable (included) to the USB Smart Cable
six-pin DBG connector (see Figure 1).
2. Attach the free end of the ribbon cable to the DBG connector on the development
board. Ensure that pin 1 on the ribbon cable (indicated by the dark stripe) is aligned
with pin 1 on the target connector.
Figure 1. Connecting the Six-Conductor Ribbon Cable
to the USB Smart Cable
Connecting the Serial Smart Cable to your Development
Board
If you are using a Z8 Encore! XP®F64XX Series Kit supplied with a Serial Smart Cable,
your PC communicates with the development board through the serial port. The
Z8
Encore! XP
Serial Smart Cable converts the RS-232 signals into the 3.3V bidirectional
open-drain signals required to communicate with the On-Chip Debugger (OCD).
Caution:

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 8 of 12
Do not connect the power supply to the development board before con-
necting the Z8 Encore! XP®Smart Cable to both the host PC and devel-
opment board.
Observe the following steps to connect Serial Smart Cable to the Development Board.
1. Connect the serial port of the PC to the
Z8 Encore! XP Smart Cable DB-9 female con-
nector.
2. Connect the
Z8 Encore! XP Smart Cable to development board pin header P2.
Connecting Power to the Development Board
Connect the power supply to the development board at Jumper J1, then to an electrical
outlet.
Getting Started Using ZDSII
Observe the following steps to open and use the ledBlink.proj sample project.
The following procedure references the ledBlink.zdsproj file, which
is located in the following filepath:

C:\Program Files\Zilog\ZDSII_Z8Encore_<version_number>
\samples\Product grouping\Z8xxxx_ledBlink\src

where <version_number> refers to your version of ZDSII and Z8xxxx
is the CPU family.

To provide examples, for ZDSII v4.10.1 and lower:

C:\Program Files\ZiLOG\ZDSII_Z8Encore!_4.10.1\
samples\Z8F642x_ledBlink\src

And for ZDSII v4.11.0 and later:

C:\Program Files\ZiLOG\ZDSII_Z8Encore_4.11.0\
samples\XP_F64XX\XP_F64XX_ledBlink\src
Caution:
Note:

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 9 of 12
1. Connect and supply power to the Development Board.
2. Run the Zilog Developer Studio II software. By default, the Zilog Developer Studio II
program is located in the Start menu in the below path:
ProgramsZilog ZDSII Z8 Encore! <version_number>ZDSII Z8
Encore! <version_number>
3. Select Open Project from the File menu. The Open Project dialog box is displayed.
The sample used in the following steps is written in the C programming
language. An assembler version of the ledBlink sample is located in the
following filepath:

Z8xxxx_ledBlink_asm\src
4. Browse to the samples folder for the ledBlink.zdsproj file, located by default in
the following filepath:
C:\Program Files\Zilog\ZDSII_Z8Encore_<version_number>\
samples\Product grouping\Z8xxxx_ledBlink\src
5. Select the ledblink.zdsproj file and click Open. The initial Zilog Developer Stu-
dio II program screen is displayed (see Figure 2).
6. To view the project source files, double-click on the Project Files folder on left side of
the IDE interface. Double-click on an individual file to open that file in the ZDSII file
editor.
The figures that follow are for reference only. You may have an updated
version of the software.
7. Select the correct debug tool from Project Settings Debugger Debug Tool.
For example, select USBSmartCable when using the USB Smart Cable.
Click F1 for additional info on how to setup the debugger.
8. Click OK.
Note:
Note:

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 10 of 12
Figure 2. ZDSII Program Screen
9. Click the Rebuild All icon to build the project. Wait for the build
to complete.
10. Click the Reset icon to connect and download the code to the de-
velopment board.
11. Click Go to start the program. The screen changes are displayed in
Figure 3.
Rebuild
All Icon
Reset
Icon
Go
Icon

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 11 of 12
Figure 3. ZDSII Active Screen
12. The three LEDs on the development board start blinking in sequence. If the LEDs do
not blink, start over from Step 2 on page 9.
13. Press the TEST pushbutton to change the sequence of the LEDs to blink in the opposite
direction.
For more information about using ZDSII and building projects for the Z8 Encore! XP®
development kit, refer to the Zilog Developer Studio II – Z8 Encore! User Manual
(UM0130).

Z8FMC16100 Series Motor Control Development Kit
Quick Start Guide
QS002810-0111 Page 12 of 12
DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.
LIFE SUPPORT POLICY
ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant
into the body, or (b) support or sustain life and whose failure to perform when properly
used in accordance with instructions for use provided in the labeling can be reasonably
expected to result in a significant injury to the user. A critical component is any
component in a life support device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
Document Disclaimer
©2011 Zilog, Inc. All rights reserved. Information in this publication concerning the
devices, applications, or technology described is intended to suggest possible uses and
may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR
PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. The
information contained within this document has been verified according to the general
principles of electrical and mechanical engineering.
Z8, Z8 Encore!, and Z8 Encore! XP are registered trademarks of Zilog, Inc. eZ8 is a
trademark of Zilog, Inc. All other product or service names are the property of their
respective owners.
Warning: