ZiLOG ZMOTION Series User manual

Getting Started with Zilog’s
ZMOTIONTM Development Kit
Using the ZMOTION Detection and Control Development Kit
TM
Users Manual
UM022801-0610
Copyright©2010 by Zilog®, All rights reserved.
www.zilog.com

Getting Started with Zilog’s ZMOTIONTM Development Kit
UM022801-0610 2 of 18
Introduction
This getting started guide acquaints users with Zilog’s ZMOTION Development Kit and provides
instructions on setting up and using the kit to demonstrate its basic operation. The following topics are
covered:
TM
Getting Started – The quickest way to get the board up and running
Installing the pyroelectric sensor
Installing the Lens
Installing ZDS-II and the USB Smart Cable – Zilog’s IDE and Debugger
Download and run the sample projects
Board Design Information
Kit Contents
ZMOTIONTM Development Board
USB Smart Cable Debugger
0.9” Focal Flat Lens Holder
0.77” Focal Circular Lens Holder
Selection of Lenses
Selection of Pyroelectric sensors
DB9 – DB9 serial cable
Wall mount power supply
CD with Sample applications and product documentation
CD with ZDS-II
Various mounting hardware
Getting Started
The kit comes with several lens and pyroelectric sensor options. To provide a quick method of getting
the kit up and running, the ZMOTION MCU is initially programmed with ZMOTION_Basic project using
the RE200B-P pyroelectric sensor and the CWM 0.5 GI V1 lens. By installing the pyroelectric sensor
and the lens and then applying power, the basic operation of the kit may be observed.
1. Install the RE200B-P pyroelectric sensor as outlined below.
2. Install the CWM 0.5 GI V1 lens as described on page 6
3. Insert the power supply output connector into J1 on the Development Board and apply AC
power to the power supply.
4. Turn on the Development Board by sliding power switch S1 to the “ON” position.
5. The Blue power LED will turn on and the Red LED will turn ON initially and stay on until the
pyroelectric sensor stabilizes. This may take 5 to 30 seconds. Once the PIR sensor is stable,
the Red LED is turned off and only comes on when motion is detected.
6. Wave your hand over the lens and notice the LED turning ON for approximately 1 second.

Getting Started with Zilog’s ZMOTIONTM Development Kit
UM022801-0610 3 of 18
ZMOTION Development Kit Contents
TM
***Picture of development kit components***
Figure 1. ZMOTION Development Kit Components
TM
USB Smart
Cable
(
1
)
Pyroelectric
Sensors
(
3
)
Power
Supply (1)
ZMOTION
Development
Board
(
1
)
DB9 - DB9
Serial Cable (1)
Machine Screws
and Nuts
4 - #4-40 x ¾”
2 - #4-40 x ½”
0.9” Focal Flat
Lens Holder (1)
0.77” Focal Circular
Lens Holder (1)
Lenses
(5)
Mica Washers
(2)
ZDS_II &
Application
CD’s (2)

Getting Started with Zilog’s ZMOTIONTM Development Kit
UM022801-0610 4 of 18
The following sections describe the operation of the kit in more detail,
including how to download and debug your own ZMOTIONTM project.
Installing the Pyroelectric Sensor
The Pyroelectric sensor used on the board can be changed by inserting the device into the
appropriate socket. Proper orientation is ensured by aligning the tab on the sensor to the silk-screen
tab on the circuit board. The tab on 3-pin pyroelectric sensors is aligned to the silk-screen tab labeled
“3 PIN” and the tab on 4-pin pyroelectric sensors is aligned to the silk-screen tab labeled “4 PIN”.
Ensure the leads on the pyroelectric sensor are trimmed such that the device sits flush on the board.
If the leads are too long and the device stands off the board, focal length will be affected which will
reduce performance. A mica washer is provided that must be installed between the pyroelectric
sensor and the socket to ensure the sensor’s metal can does not come in to contact with the sockets
on the board. See Page 17 for information on the Pyroelectric Sensor socket.
The leads on the pyroelectric sensor should be trimmed no shorter than 2.3mm (.090”) and no
longer than 3.3mm (0.130”).
Installing the Lens
The ZMOTION Development Board supports 4 lens mounting options.
TM
Lens Mounting Lens Supported
PIR Sensor Clip On NCL-9(26)
Circuit Board Clip In CWM 0.5 GI V1
Circular Lens Holder 0.77 Focal CM 0.77 GI V3
CM 0.77 GI V5
Flat Lens Holder 0.9 Focal AA 0.9 GI T1

Getting Started with Zilog’s ZMOTIONTM Development Kit
UM022801-0610 5 of 18
PIR Sensor Clip On
The lens is slid over top the PIR sensor and the notch on the PIR sensor is aligned with the notch in
the base of the lens. There are actually 2 notches in the base of the lens. The correct notch to use is
the one that is in line with the notch in the middle of the lens and is aligned with the horizontal axis of
the beam pattern.
NCL-9(26) Lens
Align PIR Sensor
Tab with this notch
NCL-9(26) Lens and PIR
Sensor installed on
ZMOTION Development
Board
TM

Getting Started with Zilog’s ZMOTIONTM Development Kit
UM022801-0610 6 of 18
Circuit Board Clip In
This lens style clips directly into the circuit board over top the PIR sensor. There are 4 mounting clips
on the lens that are aligned with the slots in the circuit board. Note the locating tab on the side of the
lens is to be aligned with the tab on the silk-screen.
Locating Tab
Mounting Slots
Mounting Slots
CWM 0.5 GI V1 Lens
Mounting Clips
Lens Mounting Area on
ZMOTION Development
Board
TM
CWM 0.5 GI V1 Lens and PIR
Sensor installed on
ZMOTION Development
Board
TM

Getting Started with Zilog’s ZMOTIONTM Development Kit
UM022801-0610 7 of 18
Circular Lens Holder 0.77 Focal
The circular lens holder is a 2 piece assembly that provides a 0.77” focal length mounting. To
assemble the lens and lens holder, place the circular lens into the base of the lens holder, aligning the
notch on the lens with the inside notch on the base. Place the circular cap over the lens and the base
ensuring the outside tab on the cap aligns with the outside tab on the base. Use the provided ¾”
machine screws (2) with a nut to secure the cap in place. Place the lens and lens holder assembly on
the to ZMOTION Development board with the arrow on the lens holder, aligned with the “Primary
Placement” arrow on the circuit board. The 4 screw holes in the circuit board should line up with the 4
mounting holes in the lens holder. Use the provided ½” machine screws (4) with a nut to secure the
lens holder in place.
TM
Notch on Lens
Circular Lens: CM 0.77 GI V5
Circular 0.77” Lens
Holder (Cap and Base)
Assembled Circular 0.77” Lens
holder and Circular Lens installed
on ZMOTION Development
Board
TM

Getting Started with Zilog’s ZMOTIONTM Development Kit
UM022801-0610 8 of 18
Flat Lens Holder 0.9 Focal
The flat lens holder is a 2 piece assembly that provides a 0.9” focal length mounting. To assemble the
lens and lens holder, place the flat lens into the inside of the cap. Ensure that the grooves of the lens
are facing inward. Place the cap over the base, ensuring the top of the lens is toward the arrow on the
base. Use the provided ¾” machine screws (2) with a nut to secure the cap in place. Place the lens
and lens holder assembly onto the ZMOTION Development board with the arrow on the lens holder
aligned with the “Primary Placement” arrow on the circuit board. The 4 screw holes in the circuit board
should line up with the 4 mounting holes in the lens holder. Use the provided ½” machine screws (4)
with a nut to secure the lens holder in place.
TM
Flat Lens: AA 0.9 GI T1
Flat 0.9” Lens Holder
(Cap and Base)
Assembled Flat 0.9”
Lens Holder and Flat
Lens

Getting Started with Zilog’s ZMOTIONTM Development Kit
UM022801-0610 9 of 18
Installing ZDS-II
Follow the steps below to install the ZDS II and documentation:
1. Insert the ZDS II CD into the CD-ROM drive. DemoShield launches automatically. If the
DemoShield does not launch automatically, open the Windows Explorer, browse to your CD-
ROM drive, and double-click launch.exe to launch the installer.
2. From the product installer list you may choose to install ZDS II alone; or both ZDS II and
associated documentation. You may also copy the documentation directly from your CD-ROM
drive to your hard disk using Windows Explorer or read the documentation directly from the
CD-ROM itself.
For customer service and technical support, Zilog® recommends you to create an account at
www.zilog.com.
Installing the USB Smart Cable
Follow the steps below for installing the USB Smart Cable and associated driver software.
Windows Vista-32
Follow the steps below to install the USB Smart Cable for Windows Vista-32.
1. Connect the USB Smart Cable to the Host PC. The Found New Hardware dialog box is
displayed.
2. Select [Locate and install the driver software (recommended)]. The Driver Software
Installation window is displayed, and then the Found New Hardware-USB Smart Cable dialog
box is displayed.
3. Select [I don’t have the disc. Show me other options].
4. Select [Browse my computer for driver software (advanced)].
5. Browse to the following driver directory:
<ZDS II Installation Directory>\device drivers\USB
The Windows Security dialog box is displayed.
6. Select [Install this driver software anyway].
7. When the software is installed, click [Close].
Windows XP
Follow the steps below to install the USB Smart Cable for Windows XP:
1. Connect the Zilog USB device to the Host PC. The Found New Hardware Wizard should
activate automatically after connecting the Zilog USB device for the first time; select [No, not
at this time] if asked to connect to Windows Update.
2. Select [Install from a list or specific location (Advanced)]; then click [Next].
Note: If the Windows Logo testing dialog appears, select [Continue Anyway].
3. Select [Search for the best driver in these locations and Include this location in search:]
4. Browse to the following driver directory and click [Next]:
<ZDS installation>\device drivers\USB\
5. Click [Next] after the appropriate driver is found.
6. Click [Finish] to complete the installation.

Getting Started with Zilog’s ZMOTIONTM Development Kit
UM022801-0610 10 of 18
Windows 2000
Follow the steps below to install the USB Smart Cable for Windows 2000:
1. Connect the Zilog USB device to the Host PC. The Found New Hardware Wizard should
activate automatically after connecting the Zilog USB device for the first time.
2. Click [Next] in the Found New Hardware Wizard after it has been activated.
3. Select [Search for a suitable driver for my device (Recommended)] and click [Next].
4. Select [Specify a location] and click [Next].
5. Browse to the following driver directory and click [OK].
<ZDS installation>\device drivers\USB\
6. Click [Next] after the appropriate driver is found.
7. Click [Finish] to complete the installation.
Windows 98SE
Follow the steps below to install the USB Smart Cable for Windows 98SE:
1. Connect the Zilog USB device to the Host PC. The Add New Hardware Wizard should activate
automatically after connecting the Zilog USB device for the first time.
2. Click [Next] in the Add New Hardware Wizard after it has been activated.
3. Select [Search for the best driver for your device (Recommended)] and click [Next].
4. Select [Specify a location] and browse to the following driver directory, and click [Next].
<ZDS installation>\device drivers\USB\
5. Click [Next] after the appropriate driver is found.
6. Click [Finish] to complete the installation.