ZKTeco LH6500 User manual

Installation Instruction
Version: 1.0
Date: Jun. 2018
LH6500

Lock Diagram
Before Installation
AB
D
C
H
L
M
P
R
E
I
J
Q
NO
F
1
K
G

Packing List
2
A N
H J L M C
S
TOB
F E G I D

3
Door Preparation
1. Check door thickness; prepare proper screws and spindles.
Note: Please install the mortise (H) and strike plate (M) according to the above
HH
HH
Left inward Right inward
Left outward Right outward
2. Check the door’s open direction.
Door Thickness D Spindles G Spindle I Screws
40 - 50 mm 30 mm 75 mm 25 mm
Note: If the door is thicker than 40-50 mm,this lock shall not be applicable.
Standpoint

4
Cautions
1. New lock is defined as always open mode until it is locked once by mifare card.
2. Please swipe authorised card, time sync card, room card at first for the new lock.
3. The lock is equipped with mechanical keys for manual unlocking. Remove the
mechanical keys from the package and keep them in a safe place.
4. To power on the lock, four alkaline AA batteries (not included) are required.
Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.
5. Do not remove batteries when the lock is in working state.
6. When battery power is low, the lock will beep to remind user to renew the batteries.
Please do not mix up positive and negative while replacing battery.
7. Avoid contacting with corrosive substances, and do not hang objects on the handle.
8. The software within the lock manages the RFID cards, for more details refer to the
software user manual.
9. If there are any questions, please do not hesitate to contact the seller.

Installation
5
desired handle
height
center line of
the handle
door thickness
40~50 mm
backset
62.5 mm
2. Remove the mortise latch plate (J)
1. Drill holes on the door
Note 1: Align the template along the vertical
center line of the mortise (H) at the desired
handle height, and tape it to door.
Note 2: Mark the holes first, then start drilling.
H
K
J

6
3. Install mortise (H)
I
I
H
K
J
K

7
5.Install spindle (D) and stud (B)
D
4.Install lock cylinder (C)
F
C
E
Note: Ensure the two triangles are in horizontal alignment.
AB
B
D
E
C
C
F
E

8
7.Install spindle (G) and (D)
D
G
6.Install outdoor unit (A)
A
G
D

9
9.Install the battery (P) and
battery cover (Q)
N
8.Install indoor unit (N)
P
O
QR

10
10.Mark and drill holes for strike
3 mm
22 mm
125 mm
89 mm
25 mm
I
ML
I

11
Step1: Remove the cover on the key hole with a hook (T ).
Step2: Insert mechanical key (S) into the key hole and rotate it at 90°.
11. Test Lock by mechanical key (S)
TS

FCC warning
12
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.

ZK Building, Wuhe Road, Gangtou,
Bantian, Buji Town, Longgang
District, Shenzhen China 518129
Tel: [phone]
Fax: [phone]
www.zkteco.com
© Copyright 2018. ZK TECO CO., LTD. ZKTeco Logo is a registered trademark of ZKTeco or a related company. All other product and company names mentioned are used for
identification purposes only and may be the trademarks of their respective owners. All specifications are subject to change without notice. All rights reser ved.