ZKTeco L4000 User manual

Installation Instruction
Version: 1.0
Date: Dec.,2014
L4000

B
A
C
D
E
H
F
GIJ
C
K
D
L
M
N
O
P
Q
Diagram
Before Installation
1

A
IJ
M
B
F
CK
E
G
D
50mm
LN
Q
30mm 40mm
Mounting Hardware Package
35-50mm door thickness
20mm
8mm
PackingList
Mounting Hardware Package
50-65mm door thickness
D
70mm
LN
45mm 55mm
H
70mm
2

1. Check door thickness, prepare the mounting hardware package and
cylinder.
Door Preparation
Door Thickness
(mm)
D Spindle Length
(mm)
N Screw Length
(mm)
L Screw Length
(mm)
Q Screw Length
(mm)
E Cylinder Length
(mm)
35-50 50 40 30 8 40
50-65 70 55 45 8 50
65-80 70 70 60 8 60
Note 1: The standard lock includes 2 mounting hardware package only, which is used for the door thickness
of 35-50mm and 50-65 mm separately.
Note 2: 40mm cylinder is recommended for the door thickness of 35-50mm. But, it can be used in the door
thickness of 50 -65 mm if the mortise is not placed along the centerline of door side.
3

3
I
I
I
I
FF
FF
2. Check door open direction.
Note 1: Mortise (F) has 2 types: one is for left open, the other is for right open. Please use the correct one.
Note 2: Strike plate (I) has 2 types: one is for inward open, the other is for outward open. Please use the
correct one.
Left inward Right inward
Left outward Right outward
Tips
1. How to change the handle direction?
Press down the component pointed by the arrow.
At the same time, rotate the handle at 180°.
Then release your hand from the pressed component.
180°
Pressdown
thecomponent
4

2.How to use mechanical key ?
A
3. How to use emergency
power?
Cautions
1. New lock is defined as always open mode.
2. Please register administrator firstly to prevent from any illegal access.
3. The lock is equipped with mechanical keys for manual unlocking. Remove mechanical keys from the
package and keep them in a safe place.
4. To power on the lock, four alkaline AA batteries (not included) are required. Non-alkaline and
rechargeable batteries ARE NOT RECOMMENDED.
5. Do not remove batteries when the lock is in working state.
6. The operation of setting lock has a stand-by time limit of 10 seconds. Without any activity, lock will shut
off after 15 seconds.
7. Keep your fingers clean when using this lock.
Remove the cover on the key
hole with screwdriver or nails.
Insert the key into key hole
and rotate 90°.
5

G
G
F
center line of the
handle
desired handle
height
Installation
door thickness
35~80mm
55mm
2. Install the mortise(F).
1. Drill holes on the door.
Note 1: Align the template along the vertical
center line of the mortise (F) at the desired
handle height, and tape it to door.
Note 2: Mark the holes first, then start drilling.
Backset
6

3.Install lock cylinder(E).
H
E
H
Note: Install lock cylinder in right direction,
then tighten screw (H) to fix it.
4.Install spindle(D).
D
Note: Ensure the red dot have to be vertically
upward.
D
7

5.Install outdoor unit(B) with gasket(C).
B
C
8

L
B
C
K
KC
L
6. Install mounting plate (K) with
gasket (C) on the door.
7. Install spindle (D) on the door.
D
9

N
8. Install indoor unit (M).
Q
9. Install the battery (O).
N
Q
O
P
Note: Push cable into the hole .
M
10

10.Mark and drill holes for striking.
3mm
69mm
38mm
180mm
130mm
15mm
(Depth)
25mm
(Depth)
27.5mm
16.5mm
21mm
25mm
I
J
G
11.Test the lock by mechanical key(A) or registered fingerprint.
A
11