ZKTeco L9000 User manual

Installation Instruction
Version: 1.0
Date: Apr., 2015
L9000

B
A
C
D
E
H
F
G
C
K
D
L
M
N
O
P
Q
Diagram
Before Installation
1
I
J
R

A
IJ N
BF
CK
PackingList
H
2
E
R
20 mm G
Wooden Door Security Door
10 mm 50 mm 70 mm
D15 mm
O
40 mm
55 mm
55 mm
70 mm
L
70 mm 85 mm
M

3
1. Check door thickness, prepare the proper screws and spindles.
Door Preparation
Door Thickness D Spindle L Screw M Screw O Screw E Cylinder
45-60 mm 40 mm 55 mm 40 mm
60-75 mm 55 mm 70 mm 50 mm
75-90 mm 70 mm 70 mm 85 mm 60 mm
50 mm
15 mm
Note: The standard package includes 50 mm cylinder only, which can be used in the door
thickness of 45-60 mm and 75-90 mm if the mortise is not placed along the centerline
of door side.

4
3
I
I
I
I
FF
FF
2. Check door open direction.
Note : 1. Mortise (F) can be applied to inward or outward directions by adjusting the direction of latch bolt. Please
refer to Tips for further details.
2. There are 2 types of mortise (F): one is for left open, the other is for right open. Please use the correct one.
Left inward Right inward
Left outward Right outward
(Without hooks)
3. Check door type.
Lock without hooks is applied to wooden door,
and lock with hooks is applied to security door.
(With hooks)

5
2. How to change the handle direction?
Tips
1. How to change the direction of latch bolt?
Step1: Press the end of latch bolt as the direction of arrow 1.
Step2: Rotate the latch bolt at 180°, which is shown as arrow 2.
180° 1
2
Loose
screw
Front Panel Back Panel

3.How to use mechanical key ? 4. How to use emergency
power?
Cautions
1. New lock is defined as always open mode.
2. Please register administrator firstly to prevent any illegal access.
3. The lock is equipped with mechanical keys for manual unlocking. Remove mechanical keys from the
package and keep them in a safe place.
4. To power on the lock, four alkaline AA batteries (not included) are required. Non-alkaline and
rechargeable batteries ARE NOT RECOMMENDED.
5. Do not remove batteries when the lock is in working state.
6. The operation of setting lock has a stand-by time limit of 10 seconds. Without any activity, lock will shut
off automatically.
7. Keep your fingers clean when using this lock.
Insert the key into key hole
and rotate it.
6
Press the cover on key hole
and contrarotate it at 30° to
remove the cover. 9V Battery

G
G
F
center line of the
handle
desired handle
height
Installation
door thickness
45~90 mm
2. Install the mortise (F)
1. Drill holes on the door
Note 1: Align the template along the vertical
center line of the mortise (F) at the desired
handle height, and tape it to door.
Note 2: Mark the holes first, then start drilling.
7
Backset 60 mm

3.Install lock cylinder (E)
H
E
H
Note: Install lock cylinder in right direction,
then tighten screw (H) to fix it.
4.Install spindle (D)
D
D
8

5.Install outdoor unit (B) with gasket (C)
B
C
9
B
C

L
B
C
K
KC
L
6. Install mounting plate (K) with
gasket (C) on the door
7. Install spindle (D) on the door
D
10
M
M

8. Install indoor unit (N)
O
9. Install the battery (P)
N
O
P
Q
Note: Push cable into the hole .
N
11
R
R

10.Mark and drill holes for strike
I
J
G
11.Test the lock by mechanical key (A) or registered fingerprint
A
12
27 mm
10 mm
7 mm
22 mm
37.5 mm
58.7 mm
36 mm
3 mm
31 mm
259 mm
G