ZKTeco AL30 Series User manual

Installation Guide
AL30 & AL40 Series Smart Lock
Version: 2.0
Date: December 2019

Important Notes Need Help?For technical documents and morePlease visit www.zkteco.com/enEmail: [e-mail] go through this Installation Guide carefully or call Customer Care before returning the product to the store.vThe contents of this installation guide may vary without any prior notices to improve the performance of our product.vWe highly recommend professional installation, in order to avoid any additional service charges that may be caused due to the improper installation of the product.vOn every installation, you must perform the initialization process just after the installation of this lock on any door as described in Initialization Procedure on page 7.vDo not insert the batteries before installing the lock!

Contents What’s in the box.........................................................................................................................1Installation Diagram(AL30B)......................................................................................................1Installation Procedure.................................................................................................................21. Setting up the door.................................................................................................................................................22. Adjust the backset of the lock to 70mm (if needed)..................................................................................33. Latch Installation......................................................................................................................................................34. Installation of Outdoor assembly.......................................................................................................................45.Installation of Mounting plate with Gasket....................................................................................................56. Installation of Indoor assembly...........................................................................................................................67. Verify Mechanical Unlock....................................................................................................................................68. Initialization of Lock................................................................................................................................................79.Mark and drill holes for the Strike box and Plate........................................................................................8FCC Warning................................................................................................................................9

Installation Diagram (AL30B)What’s in the boxScrew AScrew BIndoor assemblyStrikeboxStrikeplate16.5mm30mm35mmScrew CFor door thicknessScrew length35-40mm40-50mm50-53mm1LatchOutdoor assemblyGasketMounting plate KeysStud3M tapesOutdoor assemblyDoorGasketScrew CIndoorassemblyBattery(not icluded)MountingplateBattery CoverScrew AStrike boxStrikeplateLatchScrew BOptionalNote: Please use the appropriate set of C screws as per your door's thickness, to assure the proper functioning of the locks.

Installation Procedure
1. Setting up the door2
35mm - 53mm
60mm/70mm
1) Tape the Installation Template at the desired handle height.2) Mark for the holes and drill the marked location.3) The hole A doesn’t need to be drilled if the lock will be fixed by 3M Tapes.Important NoticeIt is not required to drill hole on the door. To aid with the stabilization of the lock during installation we have already provided 3M Tapes in the kit. If you still wish to have added stability, drill for the hole by referring to the provided Templates.Make sure your door is set up as required, prior to installation. Please use the supplied Template for drilling holes if required.A

2. Adjust the backset of the lock to 70mm (if needed)Pull-out the FaceplateRotate the FaceplateBy default, the metal shaft twists over the center as shown:60mm backsetPress the Bolt inside the Latch70mm backsetRotate it back
33. Latch Installation112UPUPBackset is the distance from the edge of the door to the center of the hole drilled on the door. The default Backset is 60mm, but if you want to change the Backset to 70mm, grasp body and twist the Faceplate as shown below:Before installing the Latch, make sure the Latch Bolt is in retracted(Unlocked)position and the arrow is facing upwards.Secure the Latch by inserting the B screws.

There are two methods to install the Outdoor assembly.vMethod 1: Installing with 3M TapesvMethod 2: Installing with Stud1Paste a 3M Tape on the Mounting plate of Outdoor assembly.22144. Installation of Outdoor assembly1) Make sure the highlighted Spindle is in the horizontalposition, as shown. 2) Route the cable through the opening the bolt.below3) Attach the Outdoor assembly to the door by inserting it through the Latch.Move the Gasket away and fix the Stud on the Mounting plate of Outdoor assembly.1) Make sure the highlighted Spindle is in the horizontalposition, as shown. 2) Route the cable through the opening the bolt.below3) Attach the Outdoor assembly to the door by inserting it through the Latch.

vMethod 1: Installing with 3M TapesvMethod 2: Installing with Stud55. Installation of Mounting plate with Gasket1) Paste a 3M Tape on the Mounting plate of Indoor assembly.2) Attach the Mounting plate to the Gasket and route the cable through the hole on the Mounting plate and Gasket. 3) Place the Gasket and Mounting plate on to the door and use 2 C screws to secure them.1) Attach the Mounting plate to the Gasket and route the cable through the hole on the Mounting plate and Gasket. 2) Place the Gasket and Mounting plate on to the door and use 3 C screws to secure them.

112266. Installation of Indoor assemblyConnect the male cable to the female connector on the Indoor assembly.Place the Indoor assembly properly on the Mounting plate. Then use A screws to secure Indoor assembly. The Knob dot must be positioned in direction of Bolt.7. Verify Mechanical UnlockRotate the Knob to check that Latch Bolt can be extended correctly or not.Insert the Key and rotate to check that Latch Bolt can be extended correctly or not.Notice: If the Knob or Key cannot control the Latch Bolt correctly, please read Installation Procedure carefully and re-install the Lock.Warning: Do not install the batteries until the proper installation of the lock!

8. Initialization of Lock7After installing the Lock, you must perform Initialization process, as explained in the steps below: 1) Rotate the Knob to make the Latch Bolt in the position. extended2) First, insert just 3 batteries in the Lock. 3) Use a needle or a pin to and the Reset Button. presshold4) Now, insert the last one battery, and do not release the Reset Button until the Lock prompts “Restore to default settings, wait a moment.” 5) After 10 seconds, the Lock will prompt “Complete”, which means the Initialization process is completed.Notice: 1. This initialization will clear all the data and detect the appropriate lock direction. 2. You can also change the direction of the Lock manually by continuously pressing the Reset Button 5 times. 3. If the Installation of the latch is in the opposite direction to the default Lock setting, there would be a noise from the Motor after inserting the final battery. When this state occurs, perform the Initialization process again to solve the issue.4. The initial Lock can be opened by any verification(Fingerprints, Passwords or Cards) until the first Administrator is registered.

219.Mark and drill holes for the Strike box and Plate35MM(1-48/127 “)
58(MM)(2-36/127 “)29(MM)(1-18/127 “)
21.5(MM)(215/254 “)33(MM)(1 19/64 “)Depth 2(MM)(10/127 “)14MM (70/127 “)8Make sure that the Strike box is in the level of Latch Bolt, then use Installation Template to drill holes.Align the Strike box and Plate with the drilled hole and use B screws to secure them.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.This device complies with part 15 of the FCC Rules. Operation is following two conditions: (1) This device must accept any interference.(2) This device must accept any interference received, including interference that may cause undesired operation.9Warning: