ZKTeco ML10 Series User manual

1
USER MANUAL
ML10 / PL10 series
Version: 2.2
Date: Jan. 2019

Table of Contents
Read Before Use.........................................................................................................4
Safety Precautions....................................................................................................................4
Structure........................................................................................................................................5
Basic Function ............................................................................................................6
User Introduction.....................................................................................................................6
Button Function........................................................................................................................6
Lock Indication ..........................................................................................................................7
Lock Initialization......................................................................................................................8
Using Mechanical Key...........................................................................................................9
9V External Battery ...............................................................................................................10
Register First Administrator.............................................................................................11
Register Other Administrators.......................................................................................12

Register Normal User..........................................................................................................13
Register Temporary User...................................................................................................14
Delete Temporary User Group......................................................................................15
Delete Normal User Group..............................................................................................16
Delete Admin Group...........................................................................................................17
Enable/Disable Normally Open Mode.....................................................................18
Disabling Normally Open Mode:.................................................................................18

Page | 4
Safety Precautions
1. Factory setting of all new locks allows any verification to unlock them.
2. The lock is equipped with mechanical keys for manually unlocking. Store the
mechanical key in a safe place.
3. Four alkaline AA batteries (not included) are required to power on the lock,
Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.
4. If the lock does not have any activity for ten seconds it will go into sleep mode.
5. For best results, place the fingerprint properly onto the fingerprint sensor.
Read Before Use

Page | 5
Structure
Front view Rear / Bottom view
1
LED
2
Fingerprint Sensor
3
Sensor Holder
4
ID Card Swiping Area
5 H
andle
6
Mechanical Key Hole
7 Battery
Box Cover
8
Battery Area
9
Button / Temporary User
10
Button / Admin user
1
1 Back LED
1
2 Button○
-/ Delete user
1
3 Button ○
+/ Add user
1
4 Reset Button
1
5 Button / Normal User
1
6 9V Emergency Battery Interface
6
1
2
3
5
4
1
4
1
5
1
6
1
3
7
8
9
10
11
12

Page | 6
User Introduction
Group Verification Mode Function
Administrator 20 (Fingerprint:10, ID Card: 10) Add/delete fingerprint or ID card; Enable
Normally Open (NO) mode; Unlock the door
Normal User 120 (Fingerprint:60, ID Card: 60) Unlock the door; Enable NO mode
Temporary User 40 (Fingerprint:20, ID Card: 20) Unlock the door; Enable NO mode
Button Function
Buttons Function
Add Users
Delete Users
Administrator User Group and Enable NO mode
Normal User Group and Enable NO mode
Temporary User Group and Enable NO mode
Basic Function

Page | 7
Lock Indication
Lock Status Indication
Successful Operation Single beep and green light blinks
Failed Operation Two beeps and red light blinks
Low battery Seven beeps and red light blinks 7 times
Unlock One beep and the lock makes a rolling sound for the first
time, which indicates the door is unlocked.
Lock The lock makes a rolling sound for the second time, which
indicates the door is locked.

Page | 8
Lock Initialization
Method 1 Method 2
Press the "Reset" button with
a pin
Press the sensor holder to
power up the lock
Loosen the pin
Press the button in order "+",
"1", "2", "3" , "-"
Initialize succeeded
One beep for each
press, the back LED
blinks green
Green light blinks
A long beep, LED blinks
green for 1 second
Note: The lock will be restored to factory defaults settings after initialization, and the door can be opened with
any fingerprint or ID card.
Operating Steps
Indication Operating Steps
Delete all normal users
Delete all administrators
Reset succeeded
Delete all temporary users
Please refer “Delet
Normal User”
Please refer “Delet
Administrator”
Please refer “Delet
Temporary User”

Page | 9
Using Mechanical Key
Step:
1. Using hex wrench, remove the screw.
2. Insert the key and unlock.
Hexagon Screw
Pull the handle out

Page | 10
9V External Battery
9V external battery is used to operate the lock when the battery is fully discharged.

Page | 11
Register First Administrator
Note: 1. The first registered user (fingerprint or ID card) will be the first administrator automatically in default
setting.
2. Admin group supports 20 users (10 for fingerprints and 10 for ID cards); you can still register 19 new
administrators in the next step.
Operating Steps Indication of the lock
Green light blinks
Single beep
One beep for the first two
successful attempt; a long beep
and LED blinks green for one
second for the third successful
attempt or the ID card
Press finger on to the sensor to wake up
the lock
Press "+" button
Place a fingerprint three times on the
fingerprint sensor or swipe ID card one
time on the card swiping area
Registration succeeded
Register new users

Page | 12
Register Other Administrators
Note: Admin group supports 20 users; you can still register 19 new administrators in this step.
Operating Steps Indication of the lock
LED blinks green
One beep
One beep for the first two
successful attempt; a long beep
and LED blinks green for one
second for the third successful
attempt or the ID card
One beep
One beep
Press finger on to the sensor to wake up
the lock
Press "+" button
Place a fingerprint three times on the
fingerprint sensor or swipe ID card one
time on the card swiping area
Registration succeeded
Register new users
Press button "1" to select admin group
Verify using admin fingerprint or card

Page | 13
Register Normal User
Note: Normal user group supports 120 users (60 for fingerprints and 60 for ID cards).
Operating Steps Indication of the lock
LED blinks green
One beep
One beep for the first two
successful attempt; a long beep
and LED blinks green for one
second for the third successful
attempt or the ID card
One beep
One beep
Press finger on to the sensor to wake up
the lock
Press "+" button
Place a fingerprint three times on the
fingerprint sensor or swipe ID card one
time on the card swiping area
Registration succeeded
Register new users
Press button "2" to select normal user
group
Verify using admin fingerprint or card

Page | 14
Register Temporary User
Note: Temporary user group supports 40 users (20 for fingerprints and 20 for ID cards).
Operating Steps Indication of the lock
LED blinks green
One beep
One beep for the first two
successful attempt; a long beep
and LED blinks green for one
second for the third successful
attempt or the ID card
One beep
One beep
Press finger on to the sensor to wake up
the lock
Press "+" button
Place a fingerprint three times on the
fingerprint sensor or swipe ID card one
time on the card swiping area
Registration succeeded
Register new users
Press button "3" to select temporary
user group
Verify using admin fingerprint or card

Page | 15
Delete Temporary User Group
Note:Deleting operation is only valid for groups.
Operating Steps Indication of the lock
Press finger on to the sensor to wake up
the lock
Press "-" button
Verify using admin fingerprint or card
Delete succeeded
Long press button "3" to delete
temporary user group
LED blinks green
One beep
A long beep, LED blinks green for
one second
One beep

Page | 16
Delete Normal User Group
Note:Deleting operation is only valid for groups.
Operating Steps Indication of the lock
Press finger on to the sensor to wake up
the lock
Press "-" button
Verify using admin fingerprint or card
Delete succeeded
Long press button "2" to delete normal
user group
LED blinks green
One beep
A long beep, LED blinks green for
one second
One beep

Page | 17
Delete Admin Group
Note:Deleting operation is only valid for groups.
Operating Steps Indication of the lock
Press finger on to the sensor to wake up
the lock
Press "-" button
Verify using admin fingerprint or card
Delete succeeded
Long press button "1" to delete admin
user group
LED blinks green
One beep
A long beep, LED blinks green for
one second
One beep

Page | 18
Enable/Disable Normally Open Mode
Note:Deleting operation is only valid for groups.
Disabling Normally Open Mode:
Verifying using any registered fingerprint or card on lock will disable Normally Open Mode.
Operating Steps Indication of the lock
Verify using any registered user
fingerprint or card
Long press "1" button for three seconds
LED blinks green
A long beep, LED blinks green for
one second

Page | 19