ZOSI C309 User manual

01/What’s in the Box
1.1 Packing List of Base Staon Kit
2-cam：
Camera*2 Baery Pack *1
5V-2A Power Supply of Base Staon*15V -1A USB Charger+Cable*1
Quick Start Guide*1
Mounng Screw Bag*2 Mounng Base*2 Reset Needle*1 Screwdriver*1
1m Network Cable*1
Base Staon*1
4-cam：
Quick Start Guide
Baery Pack *1
5V-2A Power Supply of Base Staon*1
Quick Start Guide*1
Reset Needle*1 Screwdriver*1
1m Network Cable*1
Quick Start Guide
Camera*4
5V -1A USB Charger+Cable*1
Mounng Screw Bag*4Mounng Base*4
Base Staon*1
1

1m Network Cable*1Baery Pack *1
1.2 Packing List of NVR Kit
4-cam：
Camera*4
12V-2A Power
Supply of NVR*1
5V -1A USB
Charger+Cable*1
Quick Start Guide*1
Mounng Screw Bag*4 Mounng Base*4 Reset Needle*1 Screwdriver*1
USB Mouse
NVR*1
8-cam：
Quick Start Guide
1m Network Cable*1
Baery Pack *1
Camera*8
12V-2A Power
Supply of NVR*1
5V -1A USB
Charger+Cable*1
Quick Start Guide*1
Mounng Screw Bag*8Mounng Base*8 Reset Needle*1 Screwdriver*1
USB Mouse
NVR*1
Quick Start Guide
2

2.1 Camera
Camera`s network indicator status:
Blue light and red lights on: The camera is being previewed remotely
Blue light on: The camera is paired or woken up
Blue light flashes connuously: Upgrading
Red light flashes slowly: Waing to pair with base staon
Red light on: Low baery
Blue light and red lights off: In Standby
Camera Buons:
Long press power switch for 3 seconds: Power-on/Power-off
Long press reset buon for 3 seconds: Reset to enter pairing state (The red light flashed
slowly aer the voice prompt)
02/Specificaon & Interface Descripon
①Antenna
②HD Lens
③Infrared LEDs
④Microphone
⑤Network Indicator
⑥PIR Sensor
⑦White LED Spotlight
⑧Adjusng Screw
⑨Release Buon
⑩Power Switch
⑪Loudspeaker
⑫Charge Indicator
⑬Micro SD Card Slot
⑭Retaining Screw
⑮Reset Buon
⑯Micro USB Port
3

2.2 Base Staon
2.3 NVR
①Antenna
②Micro SD Card Slot
③Pairing Buon
①Antenna
②3.5mm Audio Output
③VGA
④HDMI
⑤RJ45 Ethernet Port
⑥USB Port
⑦Power Port
④Reset
⑤RJ45 Ethernet Port
⑥Power Port
⑦Loudspeaker
⑧Network Indicator
⑨Camera Status Indicator
4
RESET DC 5V
LAN
Micro SD SYNC
NET
1
2
3
4

03/Download ZOSI CLOUD App
3.1 Search “ZOSI CLOUD” in App Store or Android Market, or scan the
QR code below to download on your smartphone (please grant the App
to obtain the corresponding permission for the first me use,
otherwise, it will cause the device fails to add, or when the camera
triggers moon detecon or alarm, the mobile phone cannot receive
the alarm push.)
Note: iOS Version required iOS 9.0 or above. Android Version requires
5.0 or above.
3.2 Register an Account
New user need to sign up by email or phone number, tap “Sign Up” and
follow the instrucons to sign up and log in.
5

04/Add Device
●4.1 Add Base Staon to APP
●4.1.1 Plug in base staon, connect the base staon to the router
connected to WAN with a Ethernet cable. And then scan QR code on
the base staon with your mobile phone and follow the prompt to add
devices. You can also scan and add in LAN (please ensure your mobile
phone and base staon are in a same LAN). Cameras paired with the
base staon will directly display on the device list aer the base staon
is successfully added.
Note: Please insert Micro SD card into the base staon before power-
ing on, otherwise the device cannot correctly read the memory card.
●4.1.2 Pair Cameras with Base Staon
Note: Baery cameras have been paired with the base staon, no
pairing is required. But if the pairing informaon between the camera
and base staon is cleared, you need to re-pair the devices, and follow
the steps below:
1) Place the cameras near the base staon at a distance of 30~100cm.
2) When the baery camera is turned on, press and hold the reset
buon for 3-5 seconds and you will hear a voice prompt from the
camera “Reset succeed, start pairing.” And then press and hold the
base staon pairing buon for 3-5 seconds and you will also hear a
voice prompt from base staon and start pairing. Aer that, both of the
cameras and the base staon will give out a voice prompt to indicate
that pairing succeed.
●4.2 Add the NVR to APP
●4.2.1 Connect NVR to Internet with an Ethernet cable aer plugging
in NVR, and then scan the QR code on NVR with your mobile phone and
follow the prompts to add devices. You can also scan and add in LAN
(please ensure your mobile phone and NVR are in a same LAN). Camer-
as paired with NVR will directly display on the device list aer NVR is
successfully added.
Note: Please install hard disk into NVR before powering on, otherwise
the device cannot correctly read the hard disk.
6

●4.2.2 Pair Cameras with NVR
Note: Baery cameras have been paired with the NVR, no pairing is
required. But if the pairing informaon between the camera and NVR
is cleaned, you need to re-pair the devices, and follow the steps below:
1) Place the camera near the NVR at a distance of 30~100cm.
2) When the baery camera is turned on, press and hold the reset
buon for 3-5 seconds and you will hear a voice prompt from the
camera “Reset succeed, start pairing.” And then turn on pairing
funcon of the NVR to add cameras. Aer that, the cameras will give
out a voice prompt to indicate that pairing succeed.
●4.3 Alarm, Preview, Playback and Device Sharing
●4.3.1 Click the App pushed or the Message icon in the App to check
the details of alarms.
●4.3.2 Click the Play icon on the device list and enter the preview
interface to enjoy live view and 2-way audio, etc.
●4.3.3 Click Playback or Cloud icon to view the recorded video on
device or on Cloud. NOTE: Cloud services need subscripon before use.
●4.3.4 Click Share icon to share cameras with others.
7

8
05/Camera Installaon
●5.1 You can place it on any flat surface: table, chair, floor etc..
●5.2 Install with Wall Mount
●5.2.1 Drill 5 holes according to the posion of mounng base,
and mount the base on the wall with the included pack of screws.
●5.2.2 Lock the two slots on the camera base to the hooks on
mounng base.
Install Mounng Base
Aach the Camera

●5.2.3 Screw your camera to the mounng base.
9
●5.2.4 Screw the baery pack at boom.
Screw the Camera
●5.2.5 Use the included screwdriver to adjust the camera to a proper
angle and ghten the adjustment screw.
Adjust camera angle

10
6.1 To reduce false alarms, please note:
-Do not install the camera in a place facing bright light, including
sunshine, bright lamp light, etc.
-Do not place the camera too close to a place where there are
frequently moving vehicles. Based on a series of tests, the recommend-
ed distance between the camera and vehicle is 15 meters (55).
-Stay away from air outlets, including air condioner, humidifier,
temperature converters, etc.
-Keep the camera at least 1 meter away from other wireless devices,
included WiFi routers and phones, in order to avoid wireless interfer-
ence.
6.2 Covering the Monitoring Area:
It is not recommended that the PIR sensor face the moving object
vercally when installing the camera, otherwise it may not be able to
detect the moon event.
It is suggested to adjust the angle between PIR sensor and detected
object larger than 10°.
06/Important Notes for Reducing
False Alarms

11
It is not recommended that the
PIR sensor face the moving object
vercally.
The path of the moving object
angle >10°
Ideal range of visibility:
2-10m (7-33)

12
07/Troubleshoong
1.Fail to Connect Internet
Please ensure that the mobile phone, camera and router are placed
close enough.
Please note that camera do not support connecng to a 5G router.
Check if the name and password of the router were correct.
Check the network seng of wireless NVR and base staon.
2.Device Offline
Check the Internet connecon of the router.
Check the connecon of NVR/base staon with router and the connec-
on of the NVR/base staon with cameras. If the router and the WiFi
password are changed, you need to reconfigure the network.
Check whether the camera baery has run out and you can plug it in
and try again.
3.No Preview
The server may be congested, try restarng the App and try again.
4.No App Push
Please make sure that the App has noficaon permissions.
Please confirm that the “Alert Push Noficaon” opon has been
turned on in the App sengs.
Please confirm that the “Alert Push Noficaon” opon has been
turned on in the camera sengs.
5.No recording
Please insert Micro SD Card before powering on.
Please make sure the camera PIR is turned on.
Please confirm the “Record” opon is turned on.
Please check the record sengs of NVR.
Please check whether the SD card status is normal in the App.