Zte MF633PLUS User manual

Check your system requirements
1. Check you have a spare USB port (USB 1.0 or 2.0)
2. You need to be running Windows 2000 / XP / Vista for a
PC or OS X 10.5 and above for a Mac
3. The recommended system requirements are:
CPU 1GHz Pentium or above
Hard Disk 20GBorabove
RAM 512Morabove
Display 800 x 600 minimum
4. You need to have Administrator rights to install and run
the software
5. We suggest you switch off your anti-virus software before
installing the USB modem. In some cases protection
software can prevent automatic installation. It is possible
to start the installation process manually by clicking the
Autorun icon when it appears.
1

Get to know your USB Modem
1 35
4 6
2
1. LED Indicator 2. Rotating USB plug
3. ExternalAntenna Port 4. Back cover
5. SIM Slot 6. MicroSD Slot
2

Insert your SIM Card
1. Open the slider panel on the back of your USB modem.
2. Insert your USIM card carefully as shown.
3. If you want to add a memory card you can do it now.Your
USB modem supports up to 4GB MicroSDHC memory.
4. Close the back cover.
Tip
Remember to keep your plastic SIM card holder. It has a
record of your phone number and a PIN number which you
will need later.
3

Insert the modem into your computer
The installation and management software is pre-loaded onto
your USB modem. Simply insert your modem into your
computer and follow the instructions on-screen. You’ll be up
and connected in about 5 minutes.
The USB modem is a Plug and Play device. Once inserted
your system will automatically detect the new hardware and
start to install the software. Be patient as it may take some
time for your computer to recognise the modem.
If nothing happens your system configuration may be
preventingAutorun.
Tips toresolve
zWindows users: Double click the Autorun icon to start the
software installation
zMAC users: Open theCD-ROM,ZTEMODEM, anddouble
click Telstra Turbo Connection Manager icon.
4

The installation method shown below is for Windows XP.
Othersystemswillfollowasimilarbutnotnecessarilyidentical
installation process:
5

Choose ‘I accept….’, and then click Next to continue.
6

Press Next to accept the default folder location, or press
Change to define your own path.
7

Please wait a few seconds for the installation to proceed…
Click Finish to complete the installation.
8

Connect to the internet
After installation the software interface will launch
automatically. Your modemwill continueinstalling for acouple
of minutes.
You’ll be ready to go as soon as you see the Connect button.
9

LEDindicator Modem Status
Red Offline.Not registered on the network
Green solid Registered on the 2G network
Green blinking Active data transfer on the 2G network
Blue solid Registered on the 3G network
Blue blinking Active data transfer on the 3G network
zThe installation will create a new shortcut on your desktop
and a new program listing under Start-Programs
zYou may have to reboot your PC or MAC after installation
is complete
zIf you have problems with the installation please contact
yoursupplierorseeourwebsite,www.zte.com.au/formore
assistance and FAQ’s
zIf you can’t connect to the internet check your SIM card is
insertedcorrectly,contactyourserviceproviderandcheck
your account is active.
10

Using your USB Modem
zPress Connect to establish a data connection using your
USB modem
zLaunch your browser or other software
zWhen you have finished your internet or email connection
remember to return to the software interface and press
Disconnect to end your session
zIf the software has been minimized then double click the
small icon on the task bar to re-open the application
window. See the task bar icon descriptions on Page 15.
TIP
Afterthecomputerwakesfromhibernationor standbymode
youmayneedto removeandinsert the modem.
11

Connected State
Note: The modem is locked to Telstra. If you use a SIM card
from another provider you may not be able to connect to the
network. Consult Telstra for more details or to unlock your
device.
12

Safe Removal of Hardware
To remove your USB modem from the computer first close
the Connection Manager then use the safe removal of
hardware process. If you remove the USB modem when it is
active the modem software and related information (eg
Phonebook records) may become corrupted.
Safely remove the modem
zEg in Windows XP, left click the icon on the Windows
taskbar
zClick on Safely Remove Hardware
zRemove the USB modem.
13

Using the Card Manager Software
System Icons
Network signal strength
New SMS message
Red Computer icon - internet Not Connected
Green Computer icon - Internet Connected
Connection - P is packet-switched, C is circuit switched
Green arrow icon - modem inserted into the computer
Red arrow icon - modem not inserted into the computer
Orange arrow icon - modem is offline
Green SIM icon – SIM/USIM card is inserted
Red SIM icon - SIM/USIM card is not inserted
Current network connection type
14

Task Bar Information
When you minimize the software the window will minimize
to an icon on the system tray. The program is still active in
the background but disappears to free your normal Windows
space. Double click the task bar icon to resize the display.
Task bar icons
Green - Modem is inserted into the computer
Red - Modem is not inserted into the computer
Orange - Modem is Offline
Red - SIM/USIM card is not inserted
No network signal
There is a new message
Modem is ready to connect to Internet
Green - Internet is Connected
15

Task bar menu
Right Click the task bar icon to access the following menu:
Deviceoffline Disconnectthemodemfromthenetwor
k
Deviceonline Connect the modem to the network
Factory Settings Restore the modem settings to
their original values
Help Enter the Help interface
About View software and hardware versions
Exit Close the software and switch off the
modem
16

Internet connection records
FromtheConnectscreenpressInternet Connection Records
to show your connection history.
The internet connection records are for information only.
17

SMS Interface
Click the SMS icon to use the SMS Interface:
18

Read Incoming Messages
Click the Inbox button to read your received messages.
19

Create a new message
zClick New Message and enter the recipient’s number
zThe recipient’s number can be entered directly or by
selecting entries from the Phonebook
zUse ‘;’ to separate multiple recipients.
20