Zte MF668+ User manual

Installation continued…
Click ‘Next’ to accept the default location or press ‘Change’ to specify your own path.The
installation takes a few minutes to complete.
Check your system requirements
USB port x 1 (USB 1.0 or 2.0*)1.
System Requirements:2.
PC – Windows 7,Vista, XP.a.
Mac - OSX 10.4.11 and above.b.
CPU 1GHz Pentium or above
Hard Disk 20GB or above
RAM 512M or above
Display 800 x 600 minimum
You need to have3. Administrator rights to install and run the software.
We suggest you switch off your anti-virus software before installing the USB modem.4.
In some cases protection software can prevent automatic installation. It is possible to
start the installation process manually by clicking the Autorun icon when it appears.
Tips
* USB 2.0 ports are preferred because they are much faster.
y
Identify the type of port on your PC and use version 2.0 ports.
y
Use the USB extender cable to obtain optimum reception.
y
There are 3 stages of installation:
y
Modem insertion, detection and installation of USB driver.i.
Install shield installation of Connection Manager software.ii.
Connection Manager launch and modem driver installation.iii.
Insert your SIM Card into the USB modem:1.
Open the modem back cover to access the SIM and MicroSD
yTM slot.
Insert the SIM card as shown with the gold contacts facing down and the bevelled
y
corner on the outside edge of the modem.
Push the SIM card in as far as it will go and replace the modem cover.
y
Connect the USB modem to your PC:2.
The computer must be switched ON and fully booted up.
y
Plug in the USB modem.The computer will start the Install Shield Wizard.
y
If your security settings prevent autorun then start the process manually.
y
Windows users:
¾Browse the Telecom Modem folder and double click Install.exe.
MAC users:
¾Open the CD-ROM,Telecom Modem, and double click Connection
Manager.
Follow the Install Shield prompts to complete the installation.
y
The Connection Manager software will start automatically and continue installing.
y
Installation Details3.
Screen shots are shown for Windows XP system.Other systems will follow a similar but
not necessarily identical process:
Click ‘Next’ to continue
MF668新西兰折页.indd 1 2009-9-24 11:47:59

Installation continued…
Press ‘Finish’ to complete - The Connection manager launches and installs the drivers:
Telecom Connection Manager - Press Connect to get on line…4.
When the installation is complete the Connection Manager will launch and continue
installing the drivers for a few minutes. After the device has nished initialising press
Connect to get on line.
LED status indication5.
LED Indicator Modem status
Red Ofine. Not registered on the network
Green solid Registered on the 2G network (roaming)
Green blinking Data active on the 2G network (roaming)
Blue solid Registered on the 3G network
Blue blinking Data active on the 3G network
Troubleshooting Tips6.
In the event of installation or connection issues try the following suggestions:
Install and test the modem in another computer1.
Check your SIM card is working in another device – eg mobile phone2.
Insert a known working SIM card into your modem3.
Conrm your account is active – contact your service provider4.
Uninstall the modem and re-install using Windows ‘Safe Mode’ – consult a PC5.
technician for help if required (PC only)
Advanced users can check Device Manager to make sure the drivers are installed6.
correctly.The full software installation is available on our website www.zte.co.nz
Using the Modem as a Mass Storage Device7.
You can insert a MicroSDTM memory card up to 8GB to use the modem as a mass storage
device.
Safely remove your modem from your computer.
y
Open the modem back cover to access the MicroSD
yTM slot.
There is a diagram showing the correct orientation of the MicroSD
yTM card printed on
the top of the MicroSDTM slot.
Check the correct orientation and carefully insert the MicroSD
yTM card.
Replace the modem cover and insert your device into your computer.
y
The MicroSD
yTM card will appear as an external drive on your computer system.
Always handle memory cards with care and avoid static discharge.
y
Safe removal of the modem from your computer8.
Whenever you need to remove the modem from your computer please close the Connection
Manager and use Safely Remove Hardware or Eject for MAC OS.
If you remove the device while the Connection Manager is still active it is possible to corrupt
the local Phonebook le.
Uninstall the modem software9.
Windows: Start > Programs >Telecom Connection Manager > Uninstall.
MAC OS X:Applications > Uninstall Telecom Connection Manager.
MF668新西兰折页.indd 2 2009-9-24 11:48:04