ZyXEL Communications P-871M Instruction Manual

ZyXEL Confidential
awp0b1 1/4
ZyXEL
Firmware Release Note
P-871M
Standard version
Release ME1(AWP.0)C0
Date: May 22 2008
Author: Allen Chiang

ZyXEL Confidential
awp0b1 2/4
ZyXEL P-871M Standard Version
Release ME1(AWP.0)C0
Release Note
Date: May 22, 2008
Supported Platforms:
ZyXEL P-871M
Versions:
System code version: ME1(AWP.0) | 05/21/2008
VDSL modem code version: 30103
Notes:
1. P-871M is a VDSL point to point solution that could be configured as CO and CPE
modem to support VDSL bridge mode. P-871M also realize LRE(Long Reach Ethernet)
technology that could be also accommodated well proven Ethernet and VDSL
technologies to extend Ethernet over single-pair phone line by using a VDSL signal. So
that, P-871M could support ultra-high data rate up to let ISP/SI deploy many kinds of
services in 1km long distance connections.
2. The CLI command “sys” will show system code version and VDSL modem code
version and P871M only support console baudrate 38400.
Features:

ZyXEL Confidential
awp0b1 3/4
Modifications in ME1(AWP.0)C0 | 05/21/2008
1. Change F/W version into FCS version
Modifications in ME1(AWP.0)b2 | 05/13/2008
1. Add VDSL link status to display “Training” or “Showtime” in CLI command “vdsl
show”.
2. Change profile 2 from “12a,PSD:997-M1c-A-7” to “12a,PSD:997-M1x-M”.
Modifications in ME1(AWP.0)b1 | 04/28/2008
1. When X-modem start to transmit and the signature of the transmitted file is correct, the
flash will be updated later.
2. Support modem code 30103 to fix the below issues.
zfix led blinking issue when powering on with RJ-11 connected
zMinimize the line rate variation
Modifications in ME1(AWP.0)b0 | 03/07/2008
1. DCC request to change the firmware version from (AWP.0)b1 to ME1(AWP.0)b0.
2. Fix the flash programming issue reported by SMT
3. Fix the display issue for PSD mask information.
Modifications in (AWP.0)b1 | 2/25/2008
1. Create this P-871M project.

ZyXEL Confidential
awp0b1 4/4
CI Command List
Command Description
sys display system status
help show this screen
exit logout
passwd change login password
default reset all configurations to default
upgrade [fw|conf] firmware/configurations upgrade
vdsl uprate [x] set/show VDSL uprate(2000 - 100000
Kbps)
downrate [y] set/show VDSL downrate(2000 - 100000
Kbps)
snr [z] set/show VDSL SNR(0 - 24 dB)
interleave [i] set/show VDSL interleave depth(0 -
100 0.5ms)
reset reset VDSL chip
reconnect force VDSL reconnect
show show VDSL parameters setting
profile (profile) set/show VDSL profile
active [on|off] active/deactive VDSL port
enet auto [on|off] set/show ENET auto negotiation mode
speed (speed) set/show ENET speed(10 or 100 Mbps)
duplex [full|half] set/show ENET duplex mode
fctrl [on|off] set/show ENET flow control
status display ENET statistics
clear clear ENET statistics