3-form SimpleSpec 600.01 User manual

For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go

Contents Overview
(1)
0-10V Slide Control
Wall Dimmer
3-60-497
small (1)
large (2)
Dimmable Power Supply
3-60-756
(1)
Fabricated Lightbox with
Reflection Panel
with Lighting Attached
small (6)
large (10)
Z-Clip
Drill Level ScrewsMeasuring Tape
Required Tools
2
For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go

Overview
48"
(1220mm)
8"
(204mm)
31"
(788mm)
Small
1
1
100W 24V PS
44"
48"
8"
8"
31"
3"
Focal LEDs
2"
3form provided
starter feed
Contractor line
14AWG 50' max
3
For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go

96"
(2439mm)
8"
(204mm)
31"
(788mm)
Large
1
2
1
2
100W 24V PS
100W 24V PS
3form provided
starter feed
Contractor line
14AWG 50' max
Focal LEDs
3"
31"
8"
8"
96"
44" 44"
Overview
4
For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go

Installation
Measure and Mark Dimensions1
3form 600.01 must be fully supported on the bottom by the millwork supplied by others. It cannot be hung on
Z-clips only. Millwork must be built to allow future removal of lightbox for access to lighting.
a
Measure loose z-clip locations on the back of the 3form Lightbox and transfer dimensions onto the millwork it will
be mounted to.
b
5
For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go

Installation
2Attach ZClips
Attach z-clips with proper fasteners to the millwork and ensure all z-clips line up with clips on the 3form Lightbox.
6
For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go

Installation
3Drill Holes for Wiring
Drill a ½" access hole in bottom
or back of 3form Lightbox in the
preferred location to allow low
voltage wiring to run to remote
driver location.
a
bDrill a ½" access hole in millwork
in the matching preferred
location to allow low voltage
wiring to run to remote driver
location.
7
For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go

Installation
4Hang the 3form Lightbox
a
Feed wiring into millwork while hanging
the 3form Lightbox onto the z-clips.
b
Remove the lower relective access panel by removing the screws in order to access the wire and pull it throught the hole
drilled in Step 3a.
8
For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go

Installation
4Hang the 3form Lightbox
Make sure the bottom of the 3form Lightbox is resting on the bottom of the millwork.
c
9
For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go

3-60-765
Dimmable Power Supply
96W
3-6-497
Dimming
Switch
96W
Add up to 50' max
of 18AWG+ wire.
Customer supplied.
Wall Slide Dimmmer (3-6-497)
can have up to 12 100 W PS
(3-60-765)
96W
Purple
Blue
Grey
White
AC/L
Brown
Green
AC/N
Black
Red
Blue
Note: Wiring is as shown unless
shown dierently on 3form
Lighting Layout Drawing
120VAC
Primary
Red (+)
Black
(-)
From PS
LED wire(+) or (-)
does not matter
3-60-765
Dimmable Power Supply
3-60-765
Dimmable Power Supply
Installation
5Connect Electrical
Make sure a qualiied electrician wires the lighting into the driver and tests lighting.
6Secure - Optional
If desired you can drill through the back of the millwork and screw into
the white relective panel of the 600.01. This will pull the unit tight to the
substrate and hold it in place.
10
For more information, please visit 3-form.com or call 800.726.0126
JUNE 2018 | MANRTG60001 | REV 002 © 2018 3form, Inc. All rights reserved.
SimpleSpec 600.01tm Installation Manual
Ready To Go