3M 45116 Manual

P a g e 1 | 8
3M Instruction Guide: 3M
TM
Locator Plate
3443-81-XX, 3D-Printed
Instructions for the assembly of 3M
TM
Ribbon
Cable Wiremount Socket Assembly, 451
Series
Instruction Guide
March 2022
78
-
9102
-
1086
-
9_C

3M Instruction Guide: 3M
TM
Locator Plate 3443-81-XX, 3D-Printed
P a g e 2 | 8
1.0 General
1.1 The assembly of 3M Ribbon Cable Wiremount Socket Assemblies, 451 Series,
0.050” x 0.050” sockets and 3M
TM
Round Conductor Flat Cable 0.025” can be
accomplished when using the 3M Locator Plates. 3443-81-XX Series; 3D-
Printed Base Plate 3443-81-00; and the 3M
TM
Assembly Press, 3640 or 3335
Models.
3M
TM
Connector
Part No.
3M
TM
Locator
Plate No.
3M
TM
Platen part
No.
3436
-
1K Shut Height Setting
3M
TM
Assembly
Press
3640 / 3316
3M
TM
Assembly
Press 3335
45104
3443
-
81
-
04
3442
-
9
7
7.5
45106
3443
-
81
-
06
3442
-
9
7
7.5
45108
3443
-
81
-
08
3442
-
9
7
7.5
45110
3443
-
81
-
10
3442
-
9
7
7.5
45112
3443
-
81
-
12
3442
-
9
7
7.5
45114
3443
-
81
-
14
3442
-
9
7
7.5
45116
3443
-
81
-
1
6
3442
-
9
7
7.5
45120
3443
-
81
-
20
3442
-
9
7
7.5
45126
3443
-
81
-
26
3442
-
9
7
7.5
45130
3443
-
81
-
30
3442
-
9
7
7.5
45134
3443
-
81
-
34
3442
-
9
7
7.5
45140
3443
-
81
-
40
3442
-
9
7
7.5
45150
3443
-
81
-
50
3442
-
9
7
7.5
2.0 Procedures for Set-up
2.1 Adjust the shut height settings. (See Figures 2-4)
3D – Printed Base Plate, 3D - Insert Locator Plate
3443-81-00
Figure 1
Base Plate and Insert Locator Plate

3M Instruction Guide: 3M
TM
Locator Plate 3443-81-XX, 3D-Printed
P a g e 3 | 8
3.0 Procedures for Adjusting Shut Height
The Shut height should be adjusted from the base before the locator plate is put into
place. The 3M
TM
Assembly Presses 3316 and 3640 are adjusted with a knob at the top
of the press. The 3M
TM
Assembly Press 3335 is adjusted with the collar on the press
shaft, and the 3M
TM
Assembly Press 3830 is self-adjusting.
3.1 The shut height adjustment is made from the base of the assembly press
without the locator
plate or platen in place.
3.2 Lower the handle of the press until the handle casting makes contact with the
press casting. (See Figure 2)
3.3 Place the shut height gauge across the press base. (See Figure 2)
Figure 2
3.4 Rotate the shut height to lower or raise adjustment feature until the bottom of
the shaft contacts the desired position on the shut height gauge. (See Figures 3
and 4)
Figure 3 Figure 4

3M Instruction Guide: 3M
TM
Locator Plate 3443-81-XX, 3D-Printed
P a g e 4 | 8
3.5 Install the 3M
TM
base plate, and appropriate locator plate insert on the press.
(See Figure 5) Add platen by positioning it parallel with the connector body and
cover. (See Figure 9)
Figure 5
4.0 Procedures for Cable Preparation
Before assembly of the connector can take plate, the cable must be prepared.
4.1 Place the cover into the locator plate. (See Figure 6)
Figure 6
4.2 Place the properly sized ribbon cable into the cover in the locator plate. (See
Figure 7)
Figure 7

3M Instruction Guide: 3M
TM
Locator Plate 3443-81-XX, 3D-Printed
P a g e 5 | 8
5.0 Procedures for Cable Termination
After the cable is prepared it is ready for termination.
5.1 Place the socket connector onto the cover over the cable, verifying the pin 1
indicator is in the correct position. (See Figure 8)
Figure 8
5.2 Bring the handle of the press down until the IDC’s press into cable and the
connector fully seats into the cover. (See figure 9)
Figure 9
5.3 Visually inspect termination to ensure that:
a. Cover is fully seated and parallel to the body.
b. Cable is properly aligned with the cover.
c. Cover retaining devices on the body are flush with the cover end.
(See Figure 10)

3M Instruction Guide: 3M
TM
Locator Plate 3443-81-XX, 3D-Printed
P a g e 6 | 8
Figure 10
(Metal fixture shown)
6.0 Strain Relief Attachment
6.1 Fold the cable back over the cover. (See Figure 11)
Figure 11
6.2 Place the strain relief in the connector over the cable, sliding the strain relief
into the slots of the connector. (See Figure 12)
Figure 12

3M Instruction Guide: 3M
TM
Locator Plate 3443-81-XX, 3D-Printed
P a g e 7 | 8
6.3 Press the strain relief down until the strain relief snaps into the correct position
on the connector. (See Figure 13)
Figure 13

3M Instruction Guide: 3M
TM
Locator Plate 3443-81-XX, 3D-Printed
P a g e 8 | 8
Unless otherwise noted, references to industry specifications are intended to indicate substantial compliance to
the material elements of the specification. Such references should not be construed as a guarantee of
compliance to all requirements in a given specification.
Regulatory: For regulatory information about this product, visit 3M.com/regs
Technical Information: The technical information, recommendations and other statements contained in this document are based upon
tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed.
Product Use: Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of
a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is
solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user’s method
of application.
Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is specifically stated on the applicable 3M product packaging
or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the
product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED
WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. If the 3M Product does not
conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the
purchase price.
Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether
direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or
strict liability.
3M is a trademark of 3M Company.
Please recycle.
©3M 2022. All rights reserved.