3M MS2 Sealant Box 4075-S User manual

3
MS2™ Sealant Box 4075-S
Instructions
June 2006
78-8135-7044-3-A

278-8135-7044-3-A
1.0 General
Use the 3M™MS2™ Sealant Box 4075-S for moisture resistance and possible reentry applications. This
procedure can be used in fold-back and inline splices and may be applied either during or after the splicing
operation. The sealant box is designed for use with the 3M™MS2™ Super Mini Splicing Modules.
Note: Apply sealant box at ambient temperatures of 32˚F (0˚C) or above.
2.0 Components
Insertion tool: To be used with up to 12
sealant boxes.
Sealant boxes: Packaged with disposable
grease retainers and liners.
Insertion Tool
Sealant Box with
Liner and Retainer
3.0 Sealant Box Installation
3.01 Remove retainer.
3.02 Peel plastic liner away from the sealant.
Discard liner and retainer.
3.03 Insert module into 3M™MS2™ Sealant Box
4075-S and press into sealant as far as possible
with uniform force on each end.

3
78-8135-7044-3-A
3.04 Place insertion tool on sealant box and lift tool
wings to press module completely into sealant
box. Be sure triangular ribs on tool wings
engage both edges of module to press it into
the sealant box.
Note: The insertion tool must be used to insure
proper installation of the sealant box.
3.05 When module is completely pressed into
sealant box, green grease should be visible
coming out of all wire positions at back of
module.
3.06 Snap latches on ends of sealant box to lock
module into place.
3.07 Remove insertion tool and repeat procedure for
remaining modules.
4.0 Sealant Box Removal
4.01 To remove module from sealant box, release
end latches and remove molded protrusions
(see arrows at right) from base of box with
snips or sheath knife. Remove module.
Note: Sealant boxes must not be reused. If a sealant
box is removed, it must be replaced with a
new sealant box.
Note: Carefully follow health, safety, and
environmental instructions as given on
Material Safety Data Sheet.

3M and MS2are trademarks of 3M Company.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information
believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you
must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability
associated with such use. Any statements related to the product which are not contained in 3M’s current
publications, or any contrary statements contained on your purchase order shall have no force or effect unless
expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time
of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is
defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or
repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M
will not be liable for any indirect, special, incidental or consequential loss or damage arising from this
3M product, regardless of the legal theory asserted.
3
Communication Markets Division
3M Telecommunications
6801 River Place Blvd.
Austin, TX 78726-9000
800.426.8688
Fax [phone]
www.3MTelecommunications.com Please recycle.
Litho in USA
© 3M 2006 78-8135-7044-3-A