3One data NP318T-8DI User manual

NP304T/NP308T/NP314T/NP318T
Series Serial Device Server
Quick Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District, Shenzhen
Website:
www.3onedata.com
Tel:
[phone]
Fax:
[phone]
【Package Checklist】
Please check whether the package and accessories are intact
while using the serial device server for the first time.
1. Serial Device Server
2. Quick installation guide
3. Straight-through cable
4. Hanger
5. Power adapter
6. CD
7. Warranty card
8. Qualify certificate
9. Two pairs of food pads
10. 3IN1 RJ45 serial port to DB9-Male conversion line (only
for 3IN1 product)
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
The product is managed industrial serial device server.
Module as follow:
Model I. NP304T-4D(3IN1)-RJ45:
4 RS-232/485/422 + 1 10/100Base-T(X)
Model II. NP314T-4D(3IN1)-RJ45:
4 RS-232/485/422 + 2 10/100Base-T(X)
Model III. NP308T-8D(3IN1)-RJ45:
8 RS-232/485/422 + 1 10/100Base-T(X)
Model IV. NP318T-8D(3IN1)-RJ45:
8 RS-232/485/422 + 2 10/100Base-T(X)
Model V. NP304T-4D(RS-232):
4 RS-232 + 1 10/100Base-T(X)
Model VI. NP314T-4D(RS-232):
4 RS-232 + 2 10/100Base-T(X)
Model VII. NP308T-8D(RS-232):
8 RS-232 + 1 10/100Base-T(X)
Model VIII. NP318T-8D(RS-232):
8 RS-232 + 2 10/100Base-T(X)
Model IX. NP304T-4DI (RS485):
4 RS-485/422 + 1 10/100Base-T(X)
Model X. NP314T-4DI (RS485):
4 RS-485/422 + 2 10/100Base-T(X)
Model XI. NP308T-8DI (RS-485):
8 RS-485/422 + 1 10/100Base-T(X)
Model XII. NP318T-8DI (RS-485):
8 RS-485/422 + 2 10/100Base-T(X)
【Panel Design】
Top view
Bottom view
Front view
Rear view
1. Power indicator
2. Running status indicator

3. Ethernet port Link/ACT indicators
4. Serial port transmission and receiving data
indicators
5. Foot pad
6. Locating holes for wall mounting
7. RS-232 or 3IN1 serial ports
8. RS-485/422 serial ports
9. Power input terminal block
10. Grounding screw
11. DIP switch
12. Console port
13. 10/100Base-T(X) Ethernet ports
【Mounting Dimension】
Unit: mm
Model I ~Model X
Model XI, Model XII
Note Before Mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running,
please don't directly contact to avoid scalding.
【Wall Mounting】
Mounting the Device
Step 1 Adopt M3 screw to install the left/right mounting
board on the device backboard.
Step 2 On the wall of device mounting, place the device on
the wall for reference or reference the mounting
dimension to mark the four screws position.
Step 3 Nail two M4 screws on the wall and keep 2mm
interspace reserved.
Step 4 Hang the device on two screws and slide
downward, then tighten the screw to enhance
stability, mounting ends.
Device Disassembling
Step 1 Device power off.
Step 2 Unscrew the screw on the wall about 2mm.
Step 3 Lift the device upward slightly, take out the device,
disassembling ends.
【Power Supply Connection】
DC power supply
The serial device server provides 3 industrial
terminal blocks, in which V+ and V- are DC
input and FG is ground input. The power
supply has nonpolarity and anti-reverse
functions. Power supply range: 12～48VDC.
Note:
Power ON operation: first connect power line to the
connection terminal of device power supply, then power
on.
Power OFF operation: first unpin the power plug, then
remove the power line, please note the operation order
above.
【Console Port Connection】
The device provides 1 channel procedure debugging port
based on RS-232 serial port. The interface adopts RJ45 port.
The PIN definition as follows.
PIN
2
3
5
PIN definition
TXD
RXD
GND
【DIP Switch Setting】

Provide 4-bit DIP switch for function setting,
where "ON" is enable valid terminal. Please
power off and power on after changing the status
of DIP switch. DIP switch definition as follow:
DIP
Decscription
Operation
1
Reserved
—
2
Restore factory
setting
Set the switch to ON, power on
again, it restores to factory
defaults, set the switch back.
3
Reserved
—
4
Reserved
—
【Serial Port Connection】
RS232 and 3IN1 RJ45 interface
Model I, Model II, Model III, and Model IV
provide 3IN1 serial port that supports
RS-232/485/422. The interface is RJ45; Model
V, Model VI, Model VII, and Model VIII support
RS-232. The interface is RJ45.
The RJ45 PIN definitions are as follows.
PIN
1
2
3
4
5
6
7
8
RS-232
DSR
RTS
GND
TXD
RXD
DCD
CTS
DTR
RS-485
—
—
GND
—
—
D-
—
D+
RS-422
—
R-
GND
R+
—
T-
—
T+
RS-485/422 Port
Model IX, Model X, Model XI, and Model
XII provide 5-pin 5.08mm pitch industrial
terminal block. The PIN definitions are as
follows.
PIN
1
2
3
4
5
RS-422
T+
T-
GND
R+
R-
RS-485
D+
D-
GND
—
—
【Checking LED Indicator】
The device provides LED indicators to monitor the device
working status with a comprehensive simplified
troubleshooting; the function of each LED is described in the
table as below:
LED
Indicate
Description
PWR
ON
The power connection is working
normally.
OFF
The power is not connected or is
not working normally.
RUN
ON
The system is not running
normally.
Blinking
The system is running normally.
OFF
The system is not running or
running abnormally.
LINK (1-2)
ON
The LAN interface has established
an active network connection.
Blinking
The LAN interface is in an active
network state.
OFF
The LAN interface has not
established an active network
connection.
TX
Port(1-4/8)
OFF
No data or abnormal data is being
received through serial port.
Blinking
Serial port is receiving data.
RX
Port(1-4/8)
OFF
No data or abnormal data is being
transmitted through serial port.
Blinking
Serial port is transmitting data.
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device’s configuration interface via IE
browser is shown as below:
Note
Single-port and double-port products have different
configuration. Please note the single and double port identifier in
front of the steps.
Single-port product: Model I, Model III, Model V,
Model VII, Model IⅩand Model XI.
Double-port product：Model II, Model IV, Model VI,
Model VIII, Model Ⅹand Model ⅩII.
Step 1 (Single port) Configure the IP addresses of
computer and the device to the same network
segment, and the network between them can be
mutually accessed.
Step 2 (Double port) Configure the IP addresses of
computer and the device to the same network
segment(The network segment of Network Port 1 is
1, and the network segment of network port 2 is 8),
and the network between them can be mutually
accessed.
Step 3 (Single port)Enter device’s IP address in the
address bar of the computer browser.
Port1：
Step 4 (Double port)Enter device’s IP address in the
address bar of the computer browser.
Port1：
Port 2：
Step 5 Enter device’s username and password in the login
window as shown below.
Step 6 Click “OK” button to login to the WEB interface of
the device.
1 8

Note:
The default IP address of the device Network port 1 is
“192.168.1.254”, the default IP address of the device
Network port 2 is “192.168.8.254”,
The default username and password of the device is
“admin”.
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
100M copper port
10/100Base-T(X) self-adapting
RJ45 port
Serial Port
3IN1: RJ45 interface
RS-232: RJ45 interface
RS-485/422 terminal block
Console port
RJ45
Indicator
Power indicator, Running status
indicator, Ethernet port Link/Act
indicator, Serial port
transmission and receiving data
indicator
Power Supply
Input power supply
12~48VDC
Access terminal
3-pin terminal block
Power Consumption
NP304T-4D(RS-232)
NP304T-4D(3IN1)-RJ45
NP314T-4D(3IN1)-RJ45
NP314T-4D(RS-232)
No-load: 2.16W@12VDC
Full-load: 3.00W@12VDC
NP308T-8D(RS-232)
NP308T-8D(3IN1)-RJ45
NP318T-8D(3IN1)-RJ45
NP318T-8D(RS-232)
No-load: 1.8W@12VDC
Full-load: 3.9W@12VDC
NP304T-4DI(RS-485)
NP314T-4DI(RS-485)
No-load: 2.94W@12VDC
Full-load: 2.94W@12VDC
NP308T-8DI(RS-485)
NP318T-8DI(RS-485)
No-load: 3.16W@12VDC
Full-load: 3.72W@12VDC
Working Environment
NP304T-4D(3IN1)-RJ45
NP314T-4D(3IN1)-RJ45
NP304T-4D(RS-232)
NP314T-4D(RS-232)
NP308T-8D(3IN1)-RJ45
NP318T-8D(3IN1)-RJ45
NP308T-8D(RS-232)
NP318T-8D(3IN1)-RJ45
Working temperature: -40℃～
75℃
Storage temperature:
-40℃～85℃
NP304T-4DI(RS-485)
NP314T-4DI(RS-485)
Working temperature: -40℃～
75℃
Storage temperature:
-40℃～75℃
NP308T-8DI(RS-485)
NP318T-8DI(RS-485)
Working temperature: -40℃～
70℃
Working temperature: -40℃～
70℃
Working humidity
5%~95% (no condensation)
Physical
Characteristics
Protection grade
IP30
Size (L×W×H)
170mm×110mm×31.50mm/
170mm×110mm×49.80mm
Weight
NP308T-8DI (RS-485)：740g
NP318T-8DI (RS-485)：740g
Others：590g
Mounting
Wall Mounting or desktop
mounting