3One data NP30XT series User manual

CLI user manual
NP30XT series serial device server
CLI user manual
Version 1.0.0, Mar. 2015

CLI user manual
Page1
Statement
Copyright Notice
Information in this document is reserved by Shenzhen 3onedata Technology Co., Ltd.
Reproduction and extract without permission is prohibited.
Trademarks Notice
and is registered trademarks of Shenzhen 3onedata
Technology Co.,Ltd. All other trademarks or regitered marks in this manual belong to their
respective manufacturers.
Agreement
As the product version upgrades or other reasons, this document is subject to change
without notice. Unless other agreement, this document only as a guide to use. All statement,
information and suggestion in this document, without warranty of any kind, either
expressed or implied.
Revision History：
Version No.
Date
Reason
V1.0.0
2013-07
First time to publish
V1.0.1
2013-09
Modify Documents
V1.0.2
2013-11
Software upgrade
V1.0.3
2015-03
Modify Documents
Notes
In reading this manual, please pay attention to the following symbols,
：Information necessary to explain.
：Special attention.

CLI user manual
Page2
Content
CHAPTER 1 ACCESS TO SERIAL SERVER SERIAL DEVICE SERVER..............................1
1.1 CONFIGURATION THROUGH TELNET.............................................................................................1
1.2 AGREEMENT................................................................................................................................2
1.3 COMMAND LINE PORT ..................................................................................................................2
1.3.1 View of Command Lines.....................................................................................................2
1.3.2 Command lines Online help.................................................................................................3
1.3.3 Frequent Incorrect Information of Command Lines............................................................4
1.3.4 History command.................................................................................................................4
CHAPTER 2 DEVICE SYSTEM BASED INFORMATION CONFIGURATION.....................5
2.1ENTER INTO THE VIEW OF DEVICE INFORMATION ..........................................................................5
2.2DISPLAY DEVICE INFORMATION ....................................................................................................5
2.3 CONFIGURATION INFORMATION ...................................................................................................6
2.4DELETE DEVICE INFORMATION .....................................................................................................6
CHAPTER 3 INFORMATION CONFIGURATION.....................................................................7
3.1 ENTER INTO SERIAL CONFIGURATION VIEW ..................................................................................7
3.2 DISPLAY SERIAL INFORMATION ....................................................................................................8
3.3 CLEAR SERIAL INCORRECT INFORMATION..................................................................................10
3.4 SERIAL PARAMETER CONFIGURATION.........................................................................................10
3.5 WORKING MODE PARAMETER CONFIGURATION ..........................................................................11
CHAPTER 4 SYSTEM MANAGEMENT ....................................................................................14
4.1 ENTER INTO THE VIEW OF SYSTEM MANAGEMENT CONFIGURATION...........................................14
4.2DISPLAYADDRESS INFORMATION................................................................................................14
4.3OVERTIME TIME CONFIGURATION ...............................................................................................15
4.4IPADDRESS,DEFAULT GATEWAY.................................................................................................15
4.5USER NAME,PASSWORD CONFIGURATION...................................................................................15
4.6FACTORY DEFAULT......................................................................................................................15
4.7 UPLOAD AND DOWNLOAD CONFIGURABLE FILES ......................................................................16
4.8 SYSTEM UPGRADE .....................................................................................................................16

CLI user manual
Page1
CHAPTER 1 Access to Serial server serial device server
The CLI user manual compliant with the products as follows:
NP302-2D(RS-232), 2 port RS-232 to Ethernet;
NP302-2D(RS-485), 2 port RS-485/422 to Ethernet;
NP304-4D(RS-232), 4 port RS-232 to Ethernet;
NP304-4DI(RS-485), 4 port RS-485/422 to Ethernet;
NP308-8D(RS-232), 8 port RS-232 to Ethernet;
NP308-8DI(RS-485), 8 port RS-485/422 to Ethernet;
NP3016-16D(RS-232), 16 port RS-232 to Ethernet;
NP3016-16DI(RS-485), 16 port RS-485/422 to Ethernet;
1.1 Configuration through Telnet
Terminal device use telnet connect to Serial server through PC, the requirements are as follows:
1. The IP address of Serial server, can get it by search or modify (Use IP command under the system management
view);
2. If PC and serial device server in the same local area network, the IP address must in a same network segment,
otherwise, PC and serial device server must cross-router.
If satisfied these two requirements, can use telnet access to serial device server, and then configure the serial
device server.
1）Establish configuration environment, just connect PC ‘s Ethernet port connect to serial device server’s
Ethernet port through Local area network
2）Before access Serial server through Telnet, need to input“Telnet+ Space+ serial server’s IP address”for
checking, Figure 1.1.1 as follows:
（Figure 1.1.1）
3）Hit “Enter”, checkout successful and till PC show“Please input hostname and password”, ask user to input
user name and password, default is admin, figure 1.1.2 as follows:
（Figure 1.1.2）

CLI user manual
Page2
4）Use command to configure Serial server and check the running statues, if need help, please input“?”at
any time. Specific configuration command, please reference“Serial server user manual”.
1.2 Agreement
1. Command line format agreement table 1.2.1 as follow
Table 1.2.1
Bold
Key words of the command show by bold type.
italic
Parameter of the command show italic type.
[ ]
It shows part in “[]”is optical when command configuration is need.
{ x | y | ... }
It shows to pick up one from two or more items.
[ x | y | ... ]
It shows to pick up one or no one from two or more items.
{ x | y | ... }
It shows to pick up one at least, all at most from two or more items.
Bold
Key words of the command show by bold type.
2. Format agreement of figure interface Table 1.2.2 as follows:
Table 1.2.2
Format
Description
< >
“< >” shows press name, like ”click<OK>”
[ ]
“[ ]” shows windows name, menu name and data list. like “eject [create user]window”
/
Multilevel is separated by “/”. Like [file/create/folder] means[create] a [folder] under the
menu of [file]
1.3 Command line port
Serial server provides command lines port and its configuration for user’s easy configuration and
management. Command lines port includes the following features:
1. Local configuration through Console port;
2. Supports history command saving which means it can save 10 pieces. History commands can be selected
by up and down key.
3. User can type in “help” or”?” to get some help;
4. Supports intelligent complement with Tab when commands input;
5. Command interpreter take the method of partial matching. User can type in conflict-free key words, such
as config command, only need to type in conf.
1.3.1 View of Command Lines
Serial server’ view of command lines aim at configuration of different functions. First of all, Serial server
establish connection, then confirmation of user name and password finished, after enter the correct user name
and password, enter “help or ?” in “switch”, enter into system view, Under the view of system, corresponding
view appears after typing indifferent command, figure 1.3.1 as follows:

CLI user manual
Page3
（Figure 1.3.1）
Table 1.3.1 system view command list
View
Function
DOS Prompt
Enter
Quit
System View
Switch#
Help or
？
Quit and
return to
user login
Information
Show or modify device
information, like software
version, IP address, etc.
Switch (information)#
Information
Exit and
return to
the view of
system
Serial device
server
Show or modify serial
information，like as baud
rate, data bit, mode
configuration
Switch (Serial)#
Serial
Manage
Show or modify configuration
information, like IP address，
subnet mask, default gateway
and password, etc.
Switch (manage)#
Manage
1.3.2 Command lines Online help
Command lines port provides the following online help:
Total help;
Partial help;
1. Total help
1）Type in <?> to get all commands and their description.
Example：
Switch#?
List --List commands of current view
Help --Help commands of current view
Quit --Exit from CLI
Exit --Exit from current view
Reboot --Reboot switch

CLI user manual
Page4
Port --Enter port setting view
Serial --Enter Serial setting menu
Manage --Enter system manage view
Information --Enter device information view
2）Type in a command and “?”, between there is a space, if key word is in this location, then type in all keywords
and descriptions.
Example:
Switch (information)# show ?
mac --show device MAC Address
version --show device version
others --show device type、name、etc
2. Partial help
1）Type in a character string with <?>. It can show all commands beginning with this character string.
Example:
Switch# m?
Manage --Enter system manage menu
2）Type in former letters of some key word of the command, press<Tab> key. If the letters are unique, it can
show the completed key word.
Example:
Switch# inf+<Tab>
Switch# information
1.3.3 Frequent Incorrect Information of Command Lines
All commands typed by users, if it is certificated by grammar, it can run correctly, or users will be sent
incorrect information. Frequent incorrect information is in table 1.4.3 as below:
Table 1.4.3 Frequent incorrect information
English incorrect information
Reason
Invalid Command
Command cannot be found.
Key word cannot be found.
The type of parameter is wrong.
The parameter is beyond the border.
Incomplete Command
Command is not completed.
Too many parameters
Parameter is too much.
Must OneToOne option!
Based mode is necessary
1.3.4 History command
Command lines port can provides the function similar to Dos key. It automatic saves command lines that
users types in, and users can use these history commands. Detailed operating please check table 1.3.4
as follows:
Table 1.3.4 access history command
Operating
Key
Result
Visit previous history command Up <↑> If it exists earlier command, it is taken out.
Visit next history command
Down <
↓
>
If it exists later command, it is taken out.

CLI user manual
Page5
CHAPTER 2 Device system based information configuration
Device information includes Device Type, Hardware Version, Device Name, Software Version, Device
Description, Device SN and Contact Way. Among them, Hardware Version and Software Version can be only read,
not modified.
2.1 Enter into the view of device information
Please check the view as figure 2.1.1 Table 2.1.1
Operating
Command
Description
Enter into the view of device information
Information
Run in the view of system
2.2 Display device information
Please check the device information command as table 2.2.1
Table 2.2.1
Operating
Command
Description
Show system version
show version
Carry out under the view of device information
Show MAC address of device
show mac
Carry out under the view of device information
Show Device Type, Name, etc.
show others
Carry out under the view of device information
Configure device model, name etc
config
Carry out under the view of device information
Delete device model, name etc
clean
Carry out under the view of device information
Example: Enter into device information view, enter the bold type command as follows and enter return key
Switch# information
Switch(information)# ?
List --List commands of current menu
Help --Help commands of current menu
Quit --Quit from CLI
Exit --Exit from current menu
Reboot --Reboot switch
Show mac --Show device MAC Address
Show version --Show device version
Show others --Show device type,name,etc
Config --Config device type,name,etc
Clean --Clean device type,name,etc /
Example: Check device name and model number etc
Switch (information)# show others
Device type Serial server
Device name Serial server
Description Serial Server
Serial number 201304160001
Contact way www.3onedata.com
Example: Check the MAC address
Switch(information)# show mac
Device MAC address : 00.22.6F.BB.00.02

CLI user manual
Page6
2.3 Configuration information
Please reference user configuration device information as table 2.3.1:
Table 2.3.1
Operating Command Description
Configure Device Type config –t type
Type: configurable type, the length is between
1～17 characters
Configure Device Name config -n name
Name: configurable name, the length is
between1～17 characters
Configure Serial Number config -m number
Number: configurable number, the length is
between 1
～
17 characters
Configure Device Description config -p description
Description: configurable description, the length
is between 1～17 characters
Configure Contact information
config -c contact
Contact: Configure Contact way 1-17 bytes
Example: Configure device name as AB123, enter the bold type command as follows and enter return key:
Switch(information)# config -n ABC123
[OK]
Example: Configure device serial number as 201304111, enter the bold type command as follows and enter return
key:
Switch(information)# config -m 201304111
[OK]
2.4 Delete device information
Please reference table 2.4.1 Table 2.4.1
Operating Command Description
Delete Device Type
Clean–t
Carry our under the view of device information
Delete Device Name
Clean -n
Carry our under the view of device information
Delete Serial Number
Clean -m
Carry our under the view of device information
Delete Device Description
Clean -p
Carry our under the view of device information
Delete Contact information
Clean -c
Carry our under the view of device information
Example: Delete device name, enter the bold type command as follows and enter return key:
Switch(information)# clean -n
[OK]
Example: Delete Serial Number, enter the bold type command as follows and enter return key:
Switch(information)# clean -m
[OK]
Example: Delete Contact information, enter the bold type command as follows and enter return key:
Switch(information)# clean -c
[OK]

CLI user manual
Page7
CHAPTER 3 Information configuration
Serial server support 2/4/8/16 port serial, each serial port included 2 mode configuration: based mode
configuration and advanced mode configuration.
Based mode: Support 0~4 sessions(option), working mode: TCP Client, TCP Server, UDP and TcpAuto.
Advanced mode: Support 0~4 sessions(option), working mode: TTCP Server, UDP.
3.1 Enter into serial configuration view
Please reference table 3.1.1 Table 3.1.1
Operating
Command
Description
Enter into serial configuration
view
Serial
Carry out under the view of
device information
Enter into serial information
configuration
Com <port>
<port>
：
Option port number
1,2,3,4
，
5,6,7,8
Example: Enter into serial configuration view, enter the bold type command as follows and enter return key:
Switch# serial
Serial(COM1)# ? // //Obtain serial configuration command
List --List commands of current menu
Help --Help commands of current menu
Quit --Quit from CLI
Exit --Exit from current menu
Reboot --Reboot switch
Show config --Show COM config information
Show link --Show COM link state information
Show err --Show COM send err data
Clear err --Clear COM send err counter
Com --Enter serial com1 setting menu
Config --Config serial
Set Packs_bytes --COM set
Set Packs_time --COM set
Set Com_mode --COM set
Set OneToMulti --COM set
Set TCP_C --COM set
Set UDP --COM set
Set TCP_S --COM set
Set TCP_A --COM set
Set Session_multi --COM set
Set TCP_S_multi --COM set
Set UDP_multi --COM set
Example: Configure parameter of COM 2, enter the bold type command as follows and enter return key:
Serial(COM1)# com 2
Serial(COM2)# ? //Obtain COM 2 configuration command
List --List commands of current menu
Help --Help commands of current menu
Quit --Quit from CLI
Exit --Exit from current menu
Reboot --Reboot switch

CLI user manual
Page8
Show config --Show COM config information
Show link --Show COM link state information
Show err --Show COM send err data
Clear err --Clear COM send err counter
Com --Enter serial com1 setting menu
Config --Config serial
Set Packs_bytes --COM set
Set Packs_time --COM set
Set Com_mode --COM set
Set OneToMulti --COM set
Set TCP_C --COM set
Set UDP --COM set
Set TCP_S --COM set
Set TCP_A --COM set
Set Session_multi --COM set
Set TCP_S_multi --COM set
Set UDP_multi --COM set
3.2 Display serial information
Please check the table 3.2.1 Table 3.2.1
Operating
Command
Description
Display information of serial
connection statues
Show link
<port_list>
<port_list>: Choice the port number of serial
1
、
2
、
3
、
4
、
5
、
6
、
7
、
8 or all optional
Statistics incorrect information
of the serial
Show err
<port_list>
<port_list>: Choice the port number of serial
1
、
2
、
3
、
4
、
5
、
6
、
7
、
8 or all optional
Display serial configuration
information
Show
config<port_list>
<port_list>: Choice the port number of serial
1
、
2
、
3
、
4
、
5
、
6
、
7
、
8 or all optional
Example: Display COM2 connection statue, enter the bold type command as follows and enter return key:
Serial(COM2)# show link 1
COM<2>
Session<1>
Session mode: TCP server
Local port: 30000
Dest ip: 192.168.17.11
Local port: 1845
Session<2>
Session<3>
Session<4>
Example: Statistics COM1 incorrect information, enter the bold type command as follows and enter return key:
Serial(COM1)# show err 1
COM<1>
COM err: 0 bytes
Session<1>
ch err: 0 bytes
Session<2>
ch err: 0 bytes

CLI user manual
Page9
Session<3>
ch err: 0 bytes
Session<4>
ch err: 0 bytes
Example: Display COM1 configuration information, enter the bold type command as follows and enter return
key:
Serial(COM1)# show config 1
COM<1>
Buadrate: 115200(bps)
Data bit: 8(bits)
Parity bit: NONE(bits)
Stop bit: 1(bits)
Packs bytes: 500(bytes)
Packs time space: 20(ms)
COM work mode: RS422
Session Option: OneToOne
Session<1>
State: Enable
Session mode: TCP server
local port: 30000
heartbeat interval: 0(S)
TCP link TimeOut: 300(S)
RealCom: Disable
Session<2>
State: Enable
Session mode: TCP server
local port: 30001
heartbeat interval: 0(S)
TCP link TimeOut: 300(S)
RealCom: Disable
Session<3>
State: Enable
Session mode: TCP server
local port: 30002
heartbeat interval: 0(S)
TCP link TimeOut: 300(S)
RealCom: Disable
Session<4>
State: Enable
Session mode: TCP server
local port: 30003
heartbeat interval: 0(S)
TCP link TimeOut: 300(S)
RealCom: Disable

CLI user manual
Page10
3.3 Clear serial incorrect information
Please check table 3.3.1 Table 3.3.1
Operating
Command
Description
Clear serial incorrect
information
clear err<port_list>
<port_list>: Choice the port number of serial
1
、
2
、
3
、
4
、
5
、
6
、
7
、
8 or all optional
3.4 Serial parameter configuration
Please check table 3.4.1 Table 3.4.1
Operating
Command
Description
Configuration serial
parameter
config
<Baudrate><pari
ty>
<Databits><stop
bits>
<Baudrate>
：
{300,600,1200,2400,4800,9600,
19200,38400,57600,115200}
<parity>
： 0 --None
1 --Odd
2 --Even
3 --Mark
4 --Space
<Databits> ： 0 --5bits
1 --6bits
2 --7bits
3 --8bits
<stopbits>
： 0 --1bit
1 --2bits
Configuration serial
data frames
Set packs_bytes
<Packs_bytes>
<Packs_bytes>: data frames range1-1460(byte)
Configuration serial
character time
space
Set packs_time
<Packs_time> <Packs_time>：Character time space 1~500ms
Configuration serial
working mode Set Com_mode <Com_mode >
<Com_mode >
：
working mode 0 RS-232
1 RS-422
2 RS-485
Example: Configuration COM2 parameter, baud rate: 300bps, parity: ODD, data bits: 6 bits, stop bits: 2bits,
enter the bold type command as follows and enter return key:
Serial(COM2)# config 300 1 1 1
[OK]
Example: Configuration data frames is 300 bytes, enter the bold type command as follows and enter return key:
Serial(COM2)# set Packs_bytes 300
[OK]
Example: Configuration character time space: 100ms, enter the bold type command as follows and enter return
key:
Serial(COM2)# set Packs_time 100
[OK]
Example: Configuration working mode is RS422, enter the bold type command as follows and enter return key:
Serial(COM2)# set Com_mode 2
[OK]

CLI user manual
Page11
3.5 Working mode parameter configuration
Please check table 3.5.1 Table 3.5.1
Operating
Command
Description
Working mode
configuration
Set OneToMulti <OneToMulti>
<OneToMulti>
：
0 --OneToOne Based mode
1 --OneToMulti Advanced mode
TCP UDP
mode
configuration
information
Set UDP <session_list> <enable>
<local_port> <dns> <dest_addr>
<dest_port> <Re
alCom>
<session_list>
：
Session choice. 1,2,3,4 or all
optional
<enable>：Open session or not
0 --disable
1 --Enable
<local_port>：Local port, range{1-65535}
<dns>：Open DNS or not
0 --disable
1 --Enable
<dest_addr>：IP configuration ip or domain
<dest_port>:Destination port, range{1-65535}
<RealCom>：Virtual COM port or not
0 --disable
1 -Enable
TCP Client
mode
configuration
information
Set TCP_C
<session_list><enable>
<local_port><dns><dest_addr><
dest_port><link_mode><heartbeat
><TCP_timeout><realCom>
<session_list>
：
Session choice. 1,2,3,4 or all
optional
<enable>：Open session or not
0 --disable
1 --Enable
<local_port>：Local port, range{1-65535}
<dns>：Open DNS or not
0 --disable
1 --Enable
<dest_addr>：IP configuration ip or domain
<dest_port>:Destination port, range{1-65535}
<link_mode>
： connection mode
0 --data active
1 --link_now
<heartbeat>：heartbeat time{0-65535(S)}
<TCP_timeout>：Timeout{0-65535(S)}
<RealCom>：Virtual COM port or not
0 --disable
1 -Enable
TCP server
mode
configuration
information
Set TCP_S
<session_list><enable><local_po
rt><heartbeat><TCP_timeout>
<realCom>
<session_list>
：
Session choice. 1,2,3,4 or all
optional
<enable>：Open session or not
0 --disable
1 --Enable
<local_port>：Local port, range{1-65535}
<heartbeat>：heartbeat time{0-65535(S)}
<TCP_timeout>：Timeout{0-65535(S)}
<RealCom>：Virtual COM port or not
0 --disable
1 -Enable

CLI user manual
Page12
Operating Command Description
TCP AUTO
mode
configuration
information
Set TCP_A
<session_list><enable><local_po
rt>
<dns><dest_addr><dest_port><li
nk_mode>
<heartbeat><TCP_timeout><real
Com>
<session_list>
：
Session choice. 1,2,3,4 or all
optional
<enable> ： Open session or not
0 --disable
1 --Enable
<local_port>
： Local port, range{1-65535}
<dns>
： Open DNS or not
0 --disable
1 --Enable
<dest_addr>
： IP configuration ip or domain
<dest_port>:Destination port, range{1-65535}
<link_mode>
： connection mode
0 --data active
1 --link_now
<heartbeat>
： heartbeat time{0-65535(S)}
<TCP_timeout>
： Timeout{0-65535(S)}
<RealCom>
： Virtual COM port or not
0 --disable
1 -Enable
Advanced
working mode Set Session_multi <net_mode>
<net_mode>
：
Working mode
1 --TCP server
2 --UDP
Advanced
TCP Server
working mode
Set TCP_S_multi <local_port>
<heartbeat> <TCP_timeout>
<RealCom>
<local_port>
：
Local port, range{1-65535}}
<heartbeat> ： heartbeat time{0-65535(S)}
<TCP_timeout>
： Timeout{0-65535(S)}
<RealCom>
： Virtual COM port or not
0 --disable
1 -Enable
Advanced
UDP
working mode
Set UDP_multi <session_list>
<local_port> <dns> <dest_addr>
<dest_addr_end> <dest_port>
<RealCom>
<session_list>
：
Session choice. 1,2,3,4 or all
optional
<local_port> ： Local port, range{1-65535}
<dns>
： Open DNS or not
0 --disable
1 --Enable
<dest_addr>
： IP configuration ip or domai
<dest_addr_end>
： IP configuration over
<dest_port>:Destination port, range{1-65535}
<link_mode>
： connection mode
0 --data active
1 --link_now
<heartbeat>
： heartbeat time{0-65535(S)}
<TCP_timeout>
： Timeout{0-65535(S)}
<RealCom>
： Virtual COM port or not
0 --disable
1 -Enable
Example: Configuration working mode is advanced, enter the bold type command as follows and enter return
key:
Serial(COM2)# set oneToMulti 1
[OK]
Example: Configuration “session:1, working mode: UDP, local port: 5555, disable DNS, IP
address:192.168.1.55, destination port: 4444, disable virtual COM port”, enter the bold type command as
follows and enter return key:

CLI user manual
Page13
Serial(COM2)# set UDP 1 1 55555 0 192.168.1.55 44444 0
[OK]
Example: Configuration“session: 1, local port: 3333, diable DNS, IP address: 192.168.17.11, destination port:
2222, connection mode: link now, heartbeat time: 0, Timeout: 20s, virtual COM port disable”, enter the bold
type command as follows and enter return key:
Serial(COM2)# set tCP_C 1 1 33333 0 192.168.17.11 22222 1 0 20 0
[OK]
Example: COM2 in advanced mode, configuration working mode: TCP server, session: 4, enter the bold type
command as follows and enter return key:
Serial(COM2)# SET session_multi 1 4
[OK]
Example: COM2 in advanced mode, configuration destination port:2000, heart time: 0s, timeout: 30s, Virtual
COM port disable, enter the bold type command as follows and enter return key:
Serial(COM2)# set TCP_S_multi 2000 0 30 0
[OK]
Example: COM2 in advanced mode, session: 1, destination: 1000, DNS disable, IP address from 192.168.17.11
to 192.168.17.254, destination port: 2000, virtual COM port disable, enter the bold type command as follows and
enter return key:Serial(COM2)# set UDP_multi 1 1000 0 192.168.17.11 192.168.17.254 2000 0
[OK]

CLI user manual
Page14
CHAPTER 4 System management
4.1 Enter into the view of System management configuration
Please check the table 4.1.1
System management configuration included:
1. The configuration of system overtime
2. The configuration of Default gateway, IP address
3. The configuration of user name and password.
4. Check out IP address, subnet mask and default gateway
5. Default factory
6. Up and download configuration files
7. System upgrade Table 4.1.1
Operating
Command
Description
Enter into the view of
system management
Manage Carry out under the view of device information
Example: Enter into the view of system management, enter the bold type command as follows and enter return
key:
Switch# manage
Switch(Manage)# ?
List --List commands of current menu
Help --Help commands of current menu
Quit --Quit from CLI
Exit --Exit from current menu
Reboot --Reboot switch
Ip --Set ip address and subnet mask
Set --Set Console Overtime
Show net_address --Show Internet address
Restore --Reset to default config
Hostname --Set hostname
Password --Set password
Gateway --Set gateway
4.2 Display address information
Please check the table 4.2.1 Table 4.2.1
Operating
Command
Description
Display address information show net_address Carry out under the view of device information
Example: Display address information, enter the bold type command as follows and enter return key:
Switch(Manage)# show net_address
Device IP address : 192.168.17.25
Device mask address : 255.255.255.0
Device gateway : 192.168.17.1

CLI user manual
Page15
4.3 Overtime time configuration
Please check the table 4.3.1
Overtime time is defined as: after enter into CLI configuration mode, overtime time with none operation,
after over time, will go to user mode automatic, re-identify user name and password
Table 4.3.1
Operating
Command
Description
The configuration of
overtime time
Set <time_out>
<time_out>: Overtime time, value[0-60], unit: minute, default
time: 5 minutes, if 0 minute, the function is closed
Example: Configuration System overtime time: 10 minutes, enter the bold type command as follows and enter
return key:
Switch (manage)# set 10
[OK]
4.4 IPaddress, default gateway
Please check the table 4.4.1
Table 4.4.1
Operating
Command
Description
Configuration of IP
address Ip <ip_address> <mask>
<ip_address>
：
ip address
<mask>
：
subnet mask
Default gateway
Gateway <gateway>
<gateway>
：
gateway address
Example: Configure IP address:192.168.1.254, subnet mask; 255.255.255.0, default gateway: 192.168.1.1,
enter the bold type command as follows and enter return key:
Switch(Manage)# ip 192.168.1.254 255.255.255.0
[OK]
Switch(Manage)# gateway 192.168.1.1
[OK]
4.5 User name, password configuration
Please check the table 4.5.1 Table 4.5.1
Operating Command Description
User name
Hostname <hostname>
<hostname>
：
only character and digit in legal
Password
Password <password> <password>
<password>
：
only character and digit in legal
4.6 Factory default
Please check the table 4.6.1 Table 4.6.1
Operating
Command
Description
Factory default
Restore
Carry out under the view of device information
Example: If need factory default, enter the bold type command as follows and enter return key:
Switch（manage）# restore

CLI user manual
Page16
Restore Settings or not? (yes/no) yes
Wait.........
4.7 Upload and Download Configurable files
Please check the table 4.7.1 Table 4.7.1
Operating
Command
Description
Upload Configurable files
Upload
Suffix of file is (.cfg)
Download Configurable files
Download
Suffix of file is (.cfg)
Example: Steps of downloading configurable files are as follows, enter the bold type command as follows and
enter return key:
1.Switch(manage)# download
Please select file path and ready to receive file .
Or press [Esc] to quit .
2. Configure Hyper Terminal and select folder of files wanted.
[Transfer] →[Receive File] →[Browse] →[Choose Folder] →[folder which user choose to save the
download files to] →[OK] →[Use protocol] →[Xmodem] →[Receive] →[file name] →[file name user
choose to save, the suffix is .cfg] →[OK]
Example: Steps of uploading configurable files are as follows, enter the bold type command as follows and
enter return key:
1. Input command
System_manage# upload
Please send configuration file, or press [Esc] to quit.
CCCCCCCCCCC
From input upload command and the first C appearing, if no operating within 2 minutes, system will quit by
itself.
2. Configure Hyper Terminal and select configurable files wanted with suffix of.cfg .
Transfer] →[Send File] →[Browse] →[choose folder] →[configurable file user choose to upload] →[Open]
→[Use Protocol] →[Xmodem]→[Send]
1. Telnet did not support this command
4.8 System Upgrade
Please check the table 4.8.1
Through hyper terminal, user can upgrade system file(Please make sure the file correct)
Table 4.8.1
Operating
Command
Description
System upgrade
Upgrade
Suffix of file is (.bin)
Example; Steps are as follows, enter the bold type command as follows and enter return key:
1. Input command:
System_manage# upgrade
Please send upgrade file, or press [Esc] to quit .

CLI user manual
Page17
CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
2. Configure Hyper Terminal and select Upgrading files wanted with suffix of .bin.
[Transfer] →[Send File] →[Browse] →[choose folder] →[configurable file user choose to upload] →
[Open] →[Use Protocol] →[Xmodem]→[Send]
1. Telnet did not support this command