4IPNET EAP210 User manual

Enterprise Access Point
Indoor EAP Series/
Outdoor OWL Series

User’s Manual
Enterprise Access Point ENGLISH
1
Copyright © 4IPNET, INC.
Copyright & Disclaimer
Copyright
The contents of this publication may not be reproduced in any part or as a whole, stored,
transcribed in an information retrieval system, translated into any language, or transmitted in any
form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or
otherwise, without the prior written permission of 4IPNET, INC.
Disclaimer
4IPNET, INC. does not assume any liability arising out the application or use of any products, or
software described herein. Neither does it convey any license under its parent rights not the parent
rights of others. 4IPNET further reserves the right to make changes in any products described herein
without notice. The publication is subject to change without notice.
Trademarks
4IPNET (4ipnet) is a registered trademark of 4IPNET, INC. Other trademarks mentioned in this
publication are used for identification purposes only and may be properties of their respective
owners.

User’s Manual
Enterprise Access Point ENGLISH
2
Copyright © 4IPNET, INC.
Table of Contents
1. Before You Start ..................................................................................................................................5
1.1 Preface.................................................................................................................................................5
1.2 Document Conventions....................................................................................................................6
1.3 Package Content................................................................................................................................7
2. System Overview and Getting Started ...........................................................................................11
2.1 Introduction of 4ipnet Access Points ...........................................................................................11
2.2 Hardware Description ...................................................................................................................12
2.3 Hardware Installation....................................................................................................................36
2.4 Access Web Management Interface.............................................................................................49
3. Connect your AP to your Network..................................................................................................52
4. Adding Virtual Access Points ..........................................................................................................58
5. Securing the AP .................................................................................................................................60
6. Creating a WDS Bridge between two APs......................................................................................71
7. Web Management Interface Configuration...................................................................................74
7.1 System...............................................................................................................................................76
7.1.1 General ............................................................................................................................ 76
7.1.2 Network Interface...........................................................................................................78
7.1.3 Port..................................................................................................................................80
7.1.4 Management ................................................................................................................... 81
7.1.5 CAPWAP .........................................................................................................................84
7.1.6 IPv6.................................................................................................................................85
7.2 Wireless............................................................................................................................................86
7.2.1 VAP Overview .................................................................................................................86
7.2.2 General ...........................................................................................................................89
7.2.3 VAP Configuration .........................................................................................................93
7.2.4 Security...........................................................................................................................95
7.2.5 Repeater .......................................................................................................................100
7.2.6 Advanced ...................................................................................................................... 102
7.2.7 Access Control .............................................................................................................. 104
7.2.8 Hotspot 2.0 ..................................................................................................................108
7.3 Firewall...........................................................................................................................................110
7.3.1 Firewall List ...................................................................................................................110
7.3.2 Service ...........................................................................................................................113
7.3.3 Advanced .......................................................................................................................114
7.4 Utilities...........................................................................................................................................115
7.4.1 Change Password...........................................................................................................115
7.4.2 Backup & Restore..........................................................................................................116

User’s Manual
Enterprise Access Point ENGLISH
3
Copyright © 4IPNET, INC.
7.4.3 System Upgrade ............................................................................................................118
7.4.4 Reboot ...........................................................................................................................118
7.4.5 Upload Certificate .........................................................................................................119
7.4.6 Channel Analysis.......................................................................................................... 120
7.4.7 Background Scan...........................................................................................................121
7.5 Status ..............................................................................................................................................122
7.5.1 Overview ....................................................................................................................... 122
7.5.2 Interfaces...................................................................................................................... 124
7.5.3 Associated Clients ........................................................................................................ 125
7.5.4 WDS Link Status .......................................................................................................... 127
7.5.5 Event Log...................................................................................................................... 128
7.5.6 Monitor......................................................................................................................... 129
8. CPE Mode Configuration (OWL530/EAP210) ..........................................................................130
8.1 System.......................................................................................................................................132
8.1.1 System Information ................................................................................................... 132
8.1.2 Operating Mode ..................................................................................................... 134
8.1.3 Network Settings .................................................................................................... 135
8.1.4 Management........................................................................................................... 138
8.2 Wireless ....................................................................................................................................140
8.2.1 General Settings ..................................................................................................... 140
8.2.2 Advanced Wireless Settings ....................................................................................141
8.2.3 Security Settings..................................................................................................... 142
8.2.4 Site Survey.............................................................................................................. 144
8.3 Firewall.....................................................................................................................................147
8.3.1 IP/ Port Forwarding............................................................................................... 147
8.3.2 Demilitarized Zone................................................................................................. 148
8.4 Utilities .....................................................................................................................................149
8.4.1 Change Password ................................................................................................... 149
8.4.2 Backup & Restore ................................................................................................... 150
8.4.3 System Upgrade ......................................................................................................151
8.4.4 Reboot .................................................................................................................... 152
8.4.5 Upload Certificate .................................................................................................. 153
8.5 Status ........................................................................................................................................154
8.5.1 System Overview .................................................................................................... 154
8.5.2 Interfaces................................................................................................................ 156
8.5.3 Event Log................................................................................................................ 159
8.5.4 Monitor................................................................................................................... 160
8.5.5 DHCP Leases ...........................................................................................................161

User’s Manual
Enterprise Access Point ENGLISH
4
Copyright © 4IPNET, INC.
8.5.6 UPnP Status............................................................................................................ 162
9. Console Interface Configuration...................................................................................................163

User’s Manual
Enterprise Access Point ENGLISH
5
Copyright © 4IPNET, INC.
1.Before You Start
1.1 Preface
This manual is intended for using by system integrators, field engineers and network administrators to help
them set up Access Points in their network environments. It contains step by step procedures and pictures to
guide users with basic network system knowledge to complete the installation.
Corresponding Software Versions for each Model
EAP210
Up to software version 1.40
EAP220
Up to software version 1.40
EAP320
Up to software version 2.40
EAP330
Up to software version 1.20
EAP701
Up to software version 1.13
EAP705
Up to software version 1.10
EAP706
Up to software version 1.10
EAP717
Up to software version 1.13
EAP727
Up to software version 1.10
EAP757
Up to software version 2.40
EAP760
Up to software version 1.20
EAP767
Up to software version 1.20
OWL530
Up to software version 1.40
OWL620
Up to software version 1.70
OWL630
Up to software version 1.20

User’s Manual
Enterprise Access Point ENGLISH
6
Copyright © 4IPNET, INC.
1.2 Document Conventions
Represents essential steps, actions, or messages that should not be ignored.
Note:
Contains related information that corresponds to a topic.
Indicates that clicking this button will save the changes you made, but you must reboot
the system for the changes to take effect.
Indicates that clicking this button will clear what you have set before the settings are
applied.

User’s Manual
Enterprise Access Point ENGLISH
7
Copyright © 4IPNET, INC.
1.3 Package Content
The standard package of EAP210 includes:
4ipnet EAP210 x1
Quick Installation Guide (QIG) x1
Console Cable x1
Power Adaptor (12V) x1
Detachable Antenna x2
The standard package of EAP220 includes:
4ipnet EAP220 x1
Quick Installation Guide (QIG) x1
Console Cable x1
Ethernet Cable x1
Power Adaptor (12V) x1
Detachable Antenna x4
The standard package of EAP320 includes:
4ipnet EAP320 x1
Quick Installation Guide (QIG) x1
Console Cable x1
Ethernet Cable x1
Power Adaptor (12V) x1
Detachable Antenna x4
The standard package of EAP330 includes:
4ipnet EAP330 x1
Quick Installation Guide (QIG) x1
Console Cable x1
Ethernet Cable x1
Power Adaptor (12V) x1
Detachable Antenna x6

User’s Manual
Enterprise Access Point ENGLISH
8
Copyright © 4IPNET, INC.
The standard package of EAP701 includes:
4ipnet EAP701 x1
Quick Installation Guide (QIG) x1
Mounting Screws x2
Surface Mounting Panel x1
Outlet Mounting Panel x1
Mounting Plate Unfastening Tool x1
Power Adaptor (5V) (Optional) x1
The standard package of EAP705 includes:
4ipnet EAP705 x1
Quick Installation Guide (QIG) x1
Mounting Screws x2
Universal Mounting Panel x1
Mounting Plate Lock Tool x1
Power Adaptor (12V) (Optional) x1
The standard package of EAP706 includes:
4ipnet EAP706 x1
Quick Installation Guide (QIG) x1
Mounting Screws x2
Universal Mounting Panel x1
Mounting Plate Lock Tool x1
Power Adaptor (12V) (Optional) x1
Detachable Antenna x4
The standard package of EAP717 includes:
4ipnet EAP717 x1
Quick Installation Guide (QIG) x1
Ethernet Cable x1
Console Cable x1
Mounting Kit x1
Power Adaptor (5V) (Optional) x1

User’s Manual
Enterprise Access Point ENGLISH
9
Copyright © 4IPNET, INC.
The standard package of EAP727 includes:
4ipnet EAP727 x1
Quick Installation Guide (QIG) x1
Mounting Kit x1
Power Adaptor (12V) (Optional) x1
The standard package of EAP757 includes:
4ipnet EAP757 x1
Quick Installation Guide (QIG) x1
Ethernet Cable x1
Mounting Kit x1
Power Adaptor (12V) (Optional) x1
The standard package of EAP760 includes:
4ipnet EAP760 x1
Quick Installation Guide (QIG) x1
Mounting Kit x1
Power Adaptor (12V) (Optional) x1
Detachable Antenna x3
The standard package of EAP767 includes:
4ipnet EAP767 x1
Quick Installation Guide (QIG) x1
Wall Mount Kit x1
Ceiling Mount Kit x1
Power Adaptor (12V) (Optional) x1
The standard package of OWL530 includes:
4ipnet OWL530 x1
Quick Installation Guide (QIG) x1
Ground Wire x1
Mounting Kit x1
Power Sourcing Equipment (Optional) x1

User’s Manual
Enterprise Access Point ENGLISH
10
Copyright © 4IPNET, INC.
The standard package of OWL620 includes:
4ipnet OWL620 x1
Quick Installation Guide (QIG) x1
Mounting Kit x1
Waterproof RJ45 Connector Pack x2
Power Sourcing Equipment (Optional) x1
The standard package of OWL630 includes:
4ipnet OWL630 x1
Quick Installation Guide (QIG) x1
Mounting Kit x1
Ground Wire x1
Waterproof RJ45 Connector Pack x2
Waterproof M12 Connector Pack x1
Power Sourcing Equipment (Optional) x1
It is recommended to keep the original packing materials for possible future shipment when repair or
maintenance is required. Any returned product should be packed in its original packaging to prevent
damage during delivery.

User’s Manual
Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
11
2. System Overview and Getting Started
2.1 Introduction of 4ipnet Access Points
Indoor –EAP210 / EAP220 / EAP320 / EAP330 / EAP701 / EAP705 / EAP706
/ EAP717 / EAP727 / EAP757 / EAP760 / EAP767
The 4ipnet’s Enterprise Access Point EAP Series are embedded with 802.11 a/b/g/n/ac MIMO
technology, designed for seamless wireless connectivity in enterprise or industrial environments of all
dimensions. EAP220 / EAP320 / EAP330 / EAP705 / EAP706 / EAP727 / EAP757 / EAP760 / EAP767
feature dual radio RF cards to offer flexible implementations needed for the growing wireless networking
applications. The EAP Series make wireless communication fast, secure and easy. They support business
grade security, namely 802.1X, and Wi-Fi Protected Access (WPA and WPA2). By pushing a purposely
built button, the 4ipWES (Press-n-Connect) feature makes it easy to bridge wireless links of multiple access
points for forming a wider wireless network coverage.
The EAP Series also features multiple ESSIDs with VLAN tags and multiple Virtual APs, great for enterprise
applications, such as separating traffic from different departments using different ESSIDs. The PoE LAN
port is able to receive power from Power over Ethernet (PoE) sourcing devices.
EAP210, EAP220, EAP320 and EAP330’s metal housing is IP50 anti-dust compliant, which means that
these Access Points are well suited to WLAN deployment in industrial environments. EAP701 / EAP705 /
EAP706 / EAP717 / EAP727 / EAP757 / EAP760 / EAP767 are packed in wall/ceiling mountable plastic
enclosures, and are built perfectly to blend in with your décor.
Outdoor –OWL530 / OWL620 / OWL630
The 4ipnet OWL530 / OWL620 / OWL630 Outdoor Access Point is embedded with dual (OWL620 and
OWL630) / single (OWL530) radio RF cards (802.11 a/b/g/n/ac MIMO) in weatherproof housing, designed
for building municipal or campus wide wireless networks in harsh outdoor environments. The OWL Series’
rust-free die-cast Aluminum housing is IP68 compliant and high wind load resilient. All the components are
designed to operate in a wide range of temperature. The OWL Series Outdoor Access Point makes wireless
communication fast, secure and easy. It supports business grade security, namely 802.1X, and Wi-Fi
Protected Access (WPA and WPA2).
Combined with a variety of directional antennas (chosen by professionals), one OWL620/OWL630 with dual
radios is easy to serve clients located in different directions as well as to cover longer range. With all
modules supporting a/b/g/n bands, more channels are available for better channel planning. For example,
to reduce radio interferences, network planners may select channels in 5 GHz for backhaul or bridges while
allocating non-overlapping channels in 2.4 GHz for serving clients.
Please note that screenshots are taken from APs which feature dual RF cards. Single RF
Card APs can be configured in the same manner from the User Interface.

User’s Manual
Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
12
2.2 Hardware Description
This section depicts the hardware information including all panel description.
EAP210
Front Panel
EAP210 Front Panel
Rear Panel
1 (1) 2 3 71 (2)4 56
EAP210 Rear Panel
1
Antenna
Connector
Reverse SMA connectors for attaching antennas.
1 (1) is the primary antenna connector and 1 (2) is the secondary.
2
12V 2A
Power Socket for the power adaptor.
3
Uplink Port
The port for uplink connection to another gateway or device. PoE (802.3af/at) is
supported.
4
WES Button
WDS Easy Setup. Press the button to build up a WDS link with another peer. 4 WDS
links can be set up.
5
Restart Button
Press to restart the system
6
LED Indicators
Power
On indicates power on.
Status
On indicates the system is ready.
WLAN
On indicates wireless network interface is ready for service.

User’s Manual
Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
13
WES
For indicating WDS connection status.
Master (Press for more
than 3 seconds)
Slave (Press once and
then release right
away)
WES Start
LED (Green) OFF and
then BLINKING SLOWLY
LED (Green) BLINKS
SLOWLY
WES Negotiate
BLINKING SLOWLY
(Green)
BLINKING RAPIDLY
(Green)
WES Success
LED (Green) ON
LED (Green) ON
WES Fail/Timeout
LED (Green) OFF
LED (Green) OFF
7
Console Port
To access EAP210 via the console interface

User’s Manual
Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
14
EAP220
Front Panel
1 2 3 4
EAP220 Front Panel

User’s Manual
Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
15
A (1)
Primary antenna connector (Ant1) for RF Card A
A (2)
Secondary antenna connector (Ant2) for RF Card A
B (1)
Primary antenna connector (Ant1) for RF Card B
B (2)
Secondary antenna connector (Ant2) for RF Card B
Rear Panel
1
Restart / Reset
Press once to restart the system; to reset the system to factory default
settings, hold for more than 5 seconds.
2
WES Button (RF B)
WDS Easy Setup. Press the button to build up a WDS link with another peer.
4 WDS links can be set up per RF card. Note that the WES Button only runs
on the 5 GHz RF Card B.
3
Console Port
To access EAP220 via the console interface.
4
LAN 1~4 Ports
The ports for connections with LAN side devices.
5
Uplink Port (PoE)
The port for uplink connection to another gateway or device. PoE (802.3at) is
supported.
6
12V 2A
Power Socket for the power adaptor

User’s Manual
Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
16
EAP320
Front Panel
EAP320 Front Panel
1
Restart / Reset
Press once to restart the system; to reset the system to factory default settings,
hold for more than 5 seconds.
2
WES Button (RF
B)
WDS Easy Setup. Press the button to build up a WDS link with another peer. 4
WDS links can be set up per RF card. Note that the WES Button only runs on the
5 GHz RF Card B.
3
Console Port
To access EAP220 via the console interface.
4
LAN 1~4 Ports
The ports for connections with LAN side devices.
5
Uplink Port (PoE)
The port for uplink connection to another gateway or device. PoE (802.3at) is
supported.
6
12V 2A
Power Socket for the power adaptor
A (1)
Primary antenna connector (Ant1) for RF Card A
A (2)
Secondary antenna connector (Ant2) for RF Card A
B (1)
Primary antenna connector (Ant1) for RF Card B
B (2)
Secondary antenna connector (Ant2) for RF Card B

User’s Manual
Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
17
Rear Panel
EAP320 Back Panel
1
12V 2A
Power Jack Socket
2
Restart / Reset
Press once to restart the system; to reset the system to factory default
settings, hold for more than 5 seconds.
3
WES Button (A / B)
WDS Easy Setup. Press the button to build up a WDS link with another
peer. 4 WDS links can be set up per RF card.
4
LED Indicators
6 indicators that displays the states of 6 various functions or progresses.
The numbers are explained on the leftmost side of the rear panel.
5
Uplink Port (PoE)
The port for uplink connection to another gateway or device. PoE is
supported.
6
LAN Ports 1~2
The ports for connections with LAN side devices.
7
Console Port
To access EAP320 via the console interface.

User’s Manual
Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
18
EAP701
Lower Panel
11 2
EAP701 Lower Panel
Upper Panel
1 2 3
EAP701 Upper Panel
1
LAN 1 –2 Ports
Attach Ethernet cables here to connect to the wired local network.
2
DC Jack 5V 2 A
Attach the power adaptor here.
1
Restart / Reset Button
Press once to restart the system; Press and hold for more than 5 seconds
to reset to factory default.
2
LED Indicators
4 LED lights. Representation is listed at the top of the panel.
3
WES Button
WDS Easy Setup. Press the button to build up a WDS link with another
peer.

User’s Manual
Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
19
Back Panel
1 2
EAP701 Lower Panel
1
110 Punchdown Block
Copper wire punch down for in-wall application
2
Uplink (PoE) Port
For Uplink connection. This port can be used to connect to a controller,
gateway, or directly to the internet. PoE is supported.